Precipitation phenomena in a powder-processed quasicrystal-reinforced Al-Cr-Mn-Co-Zr alloy

Precipitation phenomena in concentrated aluminum-base silver alloys have been studied with a variety of techniques including electron microscopy. The purpose of the present work was to investigate the dislocation reactions that occur as silver atoms precipitate (or segregate) under a relatively low supersaturation. Specimens (0.1 mm thick) of Al-1 at. % Ag were quenched from ~500°C into an oil bath at room temperature and aged 30 min. at 265°C. The initial configurations available as sites for heterogeneous precipitation will therefore include perfect prismatic dislocation loops, Frank sessile loops and random segments of grown-in dislocations.

Download Full-text

Microtwinning Evidence For The Apparent Five-Fold Symmetry in T2(Al6Li3Cu)

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100125178 ◽

1987 ◽

Vol 45 ◽

pp. 24-25

Author(s):

Kenneth S. Vecchio ◽

David B. Williams

Keyword(s):

Stable Equilibrium ◽

Equilibrium Phase ◽

Convergent Beam Electron Diffraction ◽

Icosahedral Structure ◽

Cubic Crystals ◽

Icosahedral Phases ◽

Heat Treated ◽

Zero Layer ◽

Convergent Beam ◽

Zr Alloy

Since the discovery in 1984 by Shechtman et al. of crystals which display apparent five-fold symmetry, extensive effort has been given to establishing a theoretical basis for the existence of icosahedral phases (eg.2.). Several other investigations have been centered on explaining these observations based on twinning of cubic crystals (eg.3.). Recently, the existence of a stable, equilibrium phase T2Al6 Li3Cu) possessing an icosahedral structure has been reported in the Al-Li-Cu system(4-6).In the present study an Al-2.6wt.%Li-l.5wt.%Cu-0.lwt.%Zr alloy was heat treated at 300°C for 100hrs. to produce large T2 precipitates. Convergent Beam Electron Diffraction (CBED) patterns were obtained from two-fold, three-fold, and apparent five-fold axes of T2 particles. Figure 1 shows the five-fold symmetric zero layer CBED pattern obtained from T2 particles.

Download Full-text

Growth kinetics of Al2Cu in an Al-1.5Cu thin film by in Situ TEM

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100151696 ◽

1993 ◽

Vol 51 ◽

pp. 1172-1173

Author(s):

M. Park ◽

S.J. Krause ◽

S.R. Wilson

Keyword(s):

Thin Film ◽

In Situ Tem ◽

Collector Plate ◽

Transmission Electron ◽

Device Processing ◽

Corrosion Susceptibility ◽

Precipitation Phenomena ◽

Semiconductor Chips ◽

Kinetics Of

Cu alloying in Al interconnection lines on semiconductor chips improves their resistance to electromigration and hillock growth. Excess Cu in Al can result in the formation of Cu-rich Al2Cu (θ) precipitates. These precipitates can significantly increase corrosion susceptibility due to the galvanic action between the θ-phase and the adjacent Cu-depleted matrix. The size and distribution of the θ-phase are also closely related to the film susceptibility to electromigration voiding. Thus, an important issue is the precipitation phenomena which occur during thermal device processing steps. In bulk alloys, it was found that the θ precipitates can grow via the grain boundary “collector plate mechanism” at rates far greater than allowed by volume diffusion. In a thin film, however, one might expect that the growth rate of a θ precipitate might be altered by interfacial diffusion. In this work, we report on the growth (lengthening) kinetics of the θ-phase in Al-Cu thin films as examined by in-situ isothermal aging in transmission electron microscopy (TEM).

Download Full-text

Deformation and fracture behavior of an Al-Li-Cu-Mg-Zr alloy 8090

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100178008 ◽

1990 ◽

Vol 48 (4) ◽

pp. 974-975

Author(s):

D.M. Jiang ◽

B.D. Hong

Keyword(s):

High Strength ◽

Deformation And Fracture ◽

Fracture Behaviors ◽

Aluminum Lithium ◽

Carbon Fiber Reinforced Composites ◽

Peak Aged ◽

Aluminum Lithium Alloys ◽

High Strength Aluminum Alloys ◽

Lithium Alloys ◽

Zr Alloy

Aluminum-lithium alloys have been recently got strong interests especially in the aircraft industry. Compared to conventional high strength aluminum alloys of the 2000 or 7000 series it is anticipated that these alloys offer a 10% increase in the stiffness and a 10% decrease in density, thus making them rather competitive to new up-coming non-metallic materials like carbon fiber reinforced composites.The object of the present paper is to evaluate the inluence of various microstructural features on the monotonic and cyclic deformation and fracture behaviors of Al-Li based alloy. The material used was 8090 alloy. After solution treated and waster quenched, the alloy was underaged (190°Clh), peak-aged (190°C24h) and overaged (150°C4h+230°C16h). The alloy in different aging condition was tensile and fatigue tested, the resultant fractures were observed in SEM. The deformation behavior was studied in TEM.

Download Full-text