Effects of Cu/Mg ratio and heat treatment on microstructures and mechanical properties of Al–4.6Cu–Mg–0.5Ag alloys

2015 ◽  
Vol 162 ◽  
pp. 764-770 ◽  
Author(s):  
Yu-Te Chen ◽  
Guo-Yu Nieh ◽  
Jing-Hong Wang ◽  
Ten-Fu Wu ◽  
Sheng-Long Lee
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Microstructures And Mechanical Properties

Researches on Microstructures and Mechanical Properties of Extruded Mg-Zn-Zr-Y Alloy

2007 ◽  
Vol 353-358 ◽  
pp. 715-717
Author(s):  
Jian Peng ◽  
Rong Shen Liu ◽  
Ding Fei Zhang ◽  
Cheng Meng Song
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Aging Treatment ◽  
High Strength ◽  
Treatment Processes ◽  
Medium Strength ◽  
Microstructures And Mechanical Properties ◽  
Extruded Products

The microstructures and mechanical properties of Mg-Zn-Zr-Y alloy extruded bar with different heat treatment processes were investigated, including solution treatments of 400 oC, 450 oC and 500 oC for 3 hours followed by 170 oC×24h aging treatment, and solely aging treatments of 160 oC, 180 oC for 24hours without solution after extruding. By comparing the grain size, strength and elongation of the samples, the heat treatment processes for extruded products with high strength and with medium strength were recommended.

Influence of Heat Treatment on the Microstructures and Mechanical Properties of K465 Superalloy

2016 ◽  
Vol 849 ◽  
pp. 570-579
Author(s):  
Qiang Huang ◽  
Jin Xia Song ◽  
Qing Li ◽  
Wei Peng Ren ◽  
Xin Guang Guan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Cooling Rate ◽  
Room Temperature ◽  
Rupture Life ◽  
Tensile Elongation ◽  
Solution Treatment ◽  
Stress Rupture ◽  
Stress Rupture Life ◽  
Microstructures And Mechanical Properties

The microstructures and mechanical properties of superalloy K465 under different heat treatment, including as as-cast, solution treatment and aging, were investigated. The results showed that γ' precipitates in as-cast condition exhibited two kinds of morphologies of fine regular cuboidal shape at dendritic arm and coarse irregular form in interdendritic region. MC carbides decomposed into M6C carbides partly after 1210°C/4h solution treatment. The high temperature stress-rupture life can be improved obviously with the increasing cooling rate. When cooling rate was lower than 70°C/min, the room temperature tensile elongation increased with cooling rate increasing. When cooling rate was higher than 90°C/min the room temperature tensile elongation decreased with cooling rate increasing. The proper cooling rate of 70oC/min~90oC/min is advantageous for the achievement of excellent comprehensive properties. When aging treatments continued the regularization of γ' resulted in the improvement of stress-rupture life and the reduction of tensile elongation. The mechanical property gap between the solution treatment and aging can be decreased with increasing cooling rate.

Study on Microstructures and Mechanical Properties of Die Casting Mg-xGd-3Y-0.5Zr Alloys

2013 ◽  
Vol 690-693 ◽  
pp. 44-48
Author(s):  
Feng Wang ◽  
Zhi Wang ◽  
Zheng Liu ◽  
Ping Li Mao
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Solution Heat Treatment ◽  
Die Casting ◽  
Solution Treatment ◽  
Small Variation ◽  
Strength Increase ◽  
Microstructures And Mechanical Properties ◽  
Zr Alloys

In this paper, developed a non-aluminum die casting magnesium alloys were studied based on Mg-xGd-Y-Zr（x=6, 8, 12 wt.%）alloys in cold chamber press. The microstructures and mechanical properties of die casting GWK alloys have been investigated using OM, SEM, XRD, EDS and mechanical property test. The experimental results show that with increasing Gd content of Mg-xGd-Y-Zr alloys, the tensile strength increase, but elongation decrease. In particular, die casting GWK alloys after short-term and low-temperature solid solution treatment (T4) have a small variation in grain size and more uniform microstructures, and the second phases distribute at the grain boundaries in form of discontinuous rod shape or granule shape, which result in an obvious improvement in tensile mechanical properties of alloys. The Mg-12Gd-3Y-0.5Zr die casting alloy exhibit maximum tensile strength after solution heat treatment, and the value is 269MPa at room temperature. The effect of solution heat treatment on die casting Mg-xGd-Y-Zr alloys was also discussed.

Effect of heat treatment on microstructures and mechanical properties of a cast Mg-Y-Nd-Zr alloy

2016 ◽  
Vol 667 ◽  
pp. 409-416 ◽  
Author(s):  
Huizhong Li ◽  
Feng Lv ◽  
Xiaopeng Liang ◽  
Yelong Qi ◽  
Zexiao Zhu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Microstructures And Mechanical Properties ◽  
Zr Alloy
Sign in / Sign up

Export Citation Format

Share Document