Application of bipolar electrochemistry to assess the ambient temperature corrosion resistance of solution annealed type 2205 duplex stainless steel

2021 ◽  
pp. 125183
Author(s):  
Yiqi Zhou ◽  
Dirk Lars Engelberg
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Ambient Temperature ◽  
Duplex Stainless Steel ◽  
2205 Duplex Stainless Steel ◽  
Bipolar Electrochemistry

Microstructural evolution and mechanical integrity relationship of dissimilar metal welding between 2205 duplex stainless steel and composite bimetallic plates

2021 ◽  
pp. 095440622110036
Author(s):  
Changqing Ye ◽  
Weiguo Zhai ◽  
Guangyao Lu ◽  
Qingsong Liu ◽  
Liang Ni ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Weld Metal ◽  
Duplex Stainless Steel ◽  
Intergranular Corrosion ◽  
Thermal Cycle ◽  
Filler Metal ◽  
2205 Duplex Stainless Steel ◽  
Welding Thermal Cycle ◽  
Intergranular Corrosion Resistance

In this paper, shielded metal arc welding on the dissimilar joint between 2205 duplex stainless steel and composite bimetallic plates (304 L stainless steel/10CrNi3MoV steel) with a filler metal E2209 was performed. Furthermore, the microstructure, phase, mechanical properties and intergranular corrosion resistance of the joints were investigated and element distributions of the interfaces were characterized. The results show that austenite transformed to ferrite under the influence of welding thermal cycle, and then a large amount of ferrite appeared in heat affected zone (HAZ) of 2205 duplex stainless steel. Coarse bainite grains were formed in HAZ of the 10CrNi3MoV steel near the fusion line with high temperature welding thermal cycle. Fine granular bainite was also generated in HAZ of 10CrNi3MoV steel due to the relatively short exposure time to the active temperature of grain growth. Local peak temperature near the base 10CrNi3MoV steel was still high enough to recrystallize the 10CrNi3MoV steel to form partial-recrystallization HAZ due to phase change. The filler metal was compatible with the three kinds of base materials. The thickness of the elemental diffusion interfaces layers was about 100 µm. The maximum microhardness value was obtained in the HAZ of 2205 duplex stainless steel (287 ± 14 HV), and the minimum one appeared in HAZ of SS304L (213 ± 5 HV). The maximum tensile strength of the welded joint was about 670 ± 6 MPa, and the tensile specimens fractured in ductile at matrix of the composite bimetallic plates. The impact energy of the weld metal and HAZ of the 10CrNi3MoV steel tested at –20 °C were 274 ± 6 J and 308 ± 5 J, respectively. Moreover, the intergranular corrosion resistance of the weldment including 304 L stainless steel, weld metal, HAZs and 2205 duplex stainless steel was in good agreement with the functional design requirements of materials corrosion resistance.

Influence of Sigma Phase Precipitation on Pitting Corrosion of 2507 Super-Duplex Stainless Steel

2010 ◽  
Vol 658 ◽  
pp. 380-383 ◽  
Author(s):  
Ying Han ◽  
De Ning Zou ◽  
Wei Zhang ◽  
Jun Hui Yu ◽  
Yuan Yuan Qiao
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Ambient Temperature ◽  
Duplex Stainless Steel ◽  
Pitting Corrosion ◽  
Super Duplex Stainless Steel ◽  
Phase Precipitation ◽  
Pitting Potential ◽  
Σ Phase ◽  
Pitting Corrosion Resistance

Specimens of 2507 super-duplex stainless steel aging at 850°C for 5 min, 15 min and 60 min were investigated to evaluate the pitting corrosion resistance in 3.5% NaCl solution at 30°C and 50°C. The results are correlated with the microstructures obtained with different aging time. The precipitation of σ phase remarkably decreases the pitting corrosion resistance of the steel and the specimen aged for 60 min presents the lowest pitting potential at both 30°C and 50°C. With increasing the ambient temperature from 30°C to 50°C, the pitting potential exhibits a reduction tendency, while this tendency is less obviously in enhancing the ambient temperature than in extending the isothermal aging duration from 5 to 60 min. SEM analysis shows that the surrounding regions of σ phase are the preferable sites for the formation of corrosion pits which grew up subsequently. This may be attributed to the lower content of corrosion resistance elements in these regions formatted with σ phase precipitation.

Investigation of mechanical and corrosion behavior of laser hybrid weld joint of 2205 duplex stainless steel

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Chuanbo Zheng ◽  
Cheng Zhang ◽  
Xiao Yong Wang ◽  
Jie Gu
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Duplex Stainless Steel ◽  
Base Metal ◽  
Corrosion Behavior ◽  
Welded Joints ◽  
Two Phase ◽  
Content Type ◽  
2205 Duplex Stainless Steel ◽  
Laser Hybrid

Purpose Duplex stainless steel is composed of equal amounts of austenite and ferrite, which has excellent corrosion resistance and strength. However, after the metal was welded, the ratio of austenite and ferrite in the joint is unbalanced, and secondary phase precipitates are produced, which is also an important cause of pitting corrosion in the joint. Design/methodology/approach This paper aims to study the mechanical and corrosion behavior of welded joints, by adjusting the welding parameters of laser hybrid welding, dual heat sources are used to weld 2205 duplex stainless steel. The two-phase content of different parts of the welded joint is measured to study the influence of the ratio of the two-phase on the mechanical and corrosion properties of the joint. Findings The ratio of austenite and ferrite in different welded joints has an obvious difference, and from top to bottom, the austenite content decreased gradually, and the ferrite content increased gradually. The harmful phases are precipitated in the middle and lower part of the joint. The strength of welded joints is slightly lower than that of base metal. At the same time, the fracture analysis shows that some ferrite phases are affected by the precipitate in the grain and produce quasi-cleavage fracture. The corrosion results show that the corrosion resistance of the welded joints is lower than that of the base metal, and the concentration of chloride ions affects the corrosion resistance. Originality/value In this paper, the authors use the influence of different welding processes on the two-phase ratio of the joint to further study the influence of the microstructure on the corrosion resistance and mechanical properties of the weld.

Effect of high temperature compression deformation strain rate on the microstructure and corrosion behavior of 2205 duplex stainless steel

2015 ◽  
Vol 62 (3) ◽  
pp. 163-171 ◽  
Author(s):  
Yinhui Yang ◽  
Biao Yan
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
High Temperature ◽  
Strain Rate ◽  
Duplex Stainless Steel ◽  
Corrosion Behavior ◽  
Potentiodynamic Polarization ◽  
Phase Interface ◽  
Content Type ◽  
2205 Duplex Stainless Steel

Purpose – The aim of this paper was to investigate the effect of strain rate on microstructure and corrosion behavior of 2205 duplex stainless steel, after high-temperature compression tests. Design/methodology/approach – The specimens were prepared using a Gleeble3800 thermo-simulation machine over a range of temperatures from 850 to 1,250°C and strain rates from 0.005 to 5 s−1, and the corresponding flow curves and deformation microstructure obtained were further analyzed. To evaluate the effect of strain rate on corrosion behavior, potentiodynamic polarization tests and double-loop electrochemical potentiodynamic reactivation (DL-EPR) were used to characterize the electrochemical performance. Findings – Compared with strain rate of 0.5 s−1, the worst corrosion resistance behavior from the potentiodynamic polarization test results after deformation at 0.005 s−1 was attributed to more austenite (γ) and ferrite (δ) grain boundaries or δ/γ phase interface formation due to the better effect of γ dynamic recrystallization (DRX) or δ dynamic recovery (DRV). Increasing strain rate to 5 s−1 lowered the corrosion resistance, due to the increase in dislocation density. At the low strain rate of 0.005 s−1, the susceptibility to intergranular corrosion (IGC) was comparatively high after deformation at 1050 and 1150°C with more γ/γ grains and δ/γ phase boundary formation, which was lowered with the strain rate increase to 0.5 s−1, due to suppressing effect of γ DRX. Originality/value – The paper provides the scientific basis for the practical application of hot working of 2205 duplex stainless steel.

scholarly journals Impacts of Stress Relief Treatments on Microstructure, Mechanical and Corrosion Properties of Metal Active-Gas Welding Joint of 2205 Duplex Stainless Steel

Materials ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 4272
Author(s):  
Xiao-qin Zha ◽  
Yi Xiong ◽  
Tian Zhou ◽  
Yong-feng Ren ◽  
Peng-hui Hei ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Stainless Steel ◽  
Corrosion Resistance ◽  
Duplex Stainless Steel ◽  
Welded Joints ◽  
Stress Relief ◽  
2205 Duplex Stainless Steel ◽  
Ultrasonic Peening ◽  
Stress Relieving

Stress relief treatments were carried out separately with a pneumatic chipping hammer, ultrasonic peening treatment, and heat treatment for metal active-gas welding (MAG) welded joints of 2205 duplex stainless steel. The effects of these methods on the residual stress, microstructure, mechanical properties and corrosion resistance of welded joints were studied. Results show the stress state of the weld and the surrounding area was effectively improved by the pneumatic chipping hammer and ultrasonic peening treatment, and the residual stress field of the surface layer changed from tensile stress to compressive stress. On the contrary, low-temperature stress relieving annealing had no obvious effect on stress distribution. After the pneumatic chipping hammer and ultrasonic peening treatment, the welded joints were machined and hardened. Correspondingly, strength and hardness were improved. However, the heat treatment only led to a slight decrease in strength and hardness due to the static recovery of the welded joint structure. All stress relief methods effectively improved the corrosion resistance of welded joints, with the ultrasonic peening treatment giving the best performance.

Sign in / Sign up

Export Citation Format

Share Document