Investigation of mechanical and corrosion behavior of laser hybrid weld joint of 2205 duplex stainless steel

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Chuanbo Zheng ◽  
Cheng Zhang ◽  
Xiao Yong Wang ◽  
Jie Gu
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Duplex Stainless Steel ◽  
Base Metal ◽  
Corrosion Behavior ◽  
Welded Joints ◽  
Two Phase ◽  
Content Type ◽  
2205 Duplex Stainless Steel ◽  
Laser Hybrid

Purpose Duplex stainless steel is composed of equal amounts of austenite and ferrite, which has excellent corrosion resistance and strength. However, after the metal was welded, the ratio of austenite and ferrite in the joint is unbalanced, and secondary phase precipitates are produced, which is also an important cause of pitting corrosion in the joint. Design/methodology/approach This paper aims to study the mechanical and corrosion behavior of welded joints, by adjusting the welding parameters of laser hybrid welding, dual heat sources are used to weld 2205 duplex stainless steel. The two-phase content of different parts of the welded joint is measured to study the influence of the ratio of the two-phase on the mechanical and corrosion properties of the joint. Findings The ratio of austenite and ferrite in different welded joints has an obvious difference, and from top to bottom, the austenite content decreased gradually, and the ferrite content increased gradually. The harmful phases are precipitated in the middle and lower part of the joint. The strength of welded joints is slightly lower than that of base metal. At the same time, the fracture analysis shows that some ferrite phases are affected by the precipitate in the grain and produce quasi-cleavage fracture. The corrosion results show that the corrosion resistance of the welded joints is lower than that of the base metal, and the concentration of chloride ions affects the corrosion resistance. Originality/value In this paper, the authors use the influence of different welding processes on the two-phase ratio of the joint to further study the influence of the microstructure on the corrosion resistance and mechanical properties of the weld.

Effect of high temperature compression deformation strain rate on the microstructure and corrosion behavior of 2205 duplex stainless steel

2015 ◽  
Vol 62 (3) ◽  
pp. 163-171 ◽  
Author(s):  
Yinhui Yang ◽  
Biao Yan
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
High Temperature ◽  
Strain Rate ◽  
Duplex Stainless Steel ◽  
Corrosion Behavior ◽  
Potentiodynamic Polarization ◽  
Phase Interface ◽  
Content Type ◽  
2205 Duplex Stainless Steel

Purpose – The aim of this paper was to investigate the effect of strain rate on microstructure and corrosion behavior of 2205 duplex stainless steel, after high-temperature compression tests. Design/methodology/approach – The specimens were prepared using a Gleeble3800 thermo-simulation machine over a range of temperatures from 850 to 1,250°C and strain rates from 0.005 to 5 s−1, and the corresponding flow curves and deformation microstructure obtained were further analyzed. To evaluate the effect of strain rate on corrosion behavior, potentiodynamic polarization tests and double-loop electrochemical potentiodynamic reactivation (DL-EPR) were used to characterize the electrochemical performance. Findings – Compared with strain rate of 0.5 s−1, the worst corrosion resistance behavior from the potentiodynamic polarization test results after deformation at 0.005 s−1 was attributed to more austenite (γ) and ferrite (δ) grain boundaries or δ/γ phase interface formation due to the better effect of γ dynamic recrystallization (DRX) or δ dynamic recovery (DRV). Increasing strain rate to 5 s−1 lowered the corrosion resistance, due to the increase in dislocation density. At the low strain rate of 0.005 s−1, the susceptibility to intergranular corrosion (IGC) was comparatively high after deformation at 1050 and 1150°C with more γ/γ grains and δ/γ phase boundary formation, which was lowered with the strain rate increase to 0.5 s−1, due to suppressing effect of γ DRX. Originality/value – The paper provides the scientific basis for the practical application of hot working of 2205 duplex stainless steel.

Effect of hydrogen on semiconductor properties and pitting initiation of 2205 duplex stainless steel passivation film

2020 ◽  
Vol 67 (3) ◽  
pp. 313-320 ◽  
Author(s):  
Chuanbo Zheng ◽  
Jiayan Huang ◽  
Gua Yi
Keyword(s):  
Stainless Steel ◽  
Duplex Stainless Steel ◽  
Passive Film ◽  
Corrosion Behavior ◽  
Current Density ◽  
Anodic Polarization ◽  
Content Type ◽  
2205 Duplex Stainless Steel ◽  
Passivation Film ◽  
Semiconductor Properties

Purpose This paper aims to study the effect of current density of hydrogen charging on the semiconductor properties and pitting initiation of 2205 duplex stainless steel (DSS) passivation film. Design/methodology/approach In this work, the 2205 DSS is pre-hydrogenated and passivated. Then, the passivation film is tested by electrochemical impedance method, Mott–Schottky curve method and dynamic potential scanning method. The influences of hydrogen on the properties of the passivation film and the corrosion behavior of the matrix were studied by analyzing the curves obtained in the electrochemical test. The surface of the passivation film after pre-hydrogenation and anodic polarization was observed by using the ultra-depth three-dimensional microscopy and the scanning electron microscope. The integrity, density and corrosion morphology of the passivation film were studied and discussed. Findings With the increase of the hydrogen current density, the growth of the passivation film is hindered, the concentrations of donor and acceptor in the film are increased, the conductivity of the passivation film increases. In the anodic polarization, the dimensional passive current density increases with the increase of the hydrogen current density, and the pitting potential is reversed, the more likely the sample is pitting. In general, hydrogen hinders the formation of the passive film on duplex stainless steel, which increases the concentration of point defects in the passive film. Finally, the passive film is easy to crack and pitting. Originality/value The performance of passive film is an important condition to influence the corrosion behavior of stainless steel. However, little research has been done on the effects of hydrogen on the electrochemistry and pitting sensitivity of 2205 DSS passivation films. The effect of hydrogen on semiconductor properties and pitting initiation of 2205 DSS passivation film is needed to be investigated.

scholarly journals Impacts of Stress Relief Treatments on Microstructure, Mechanical and Corrosion Properties of Metal Active-Gas Welding Joint of 2205 Duplex Stainless Steel

Materials ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 4272
Author(s):  
Xiao-qin Zha ◽  
Yi Xiong ◽  
Tian Zhou ◽  
Yong-feng Ren ◽  
Peng-hui Hei ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Stainless Steel ◽  
Corrosion Resistance ◽  
Duplex Stainless Steel ◽  
Welded Joints ◽  
Stress Relief ◽  
2205 Duplex Stainless Steel ◽  
Ultrasonic Peening ◽  
Stress Relieving

Stress relief treatments were carried out separately with a pneumatic chipping hammer, ultrasonic peening treatment, and heat treatment for metal active-gas welding (MAG) welded joints of 2205 duplex stainless steel. The effects of these methods on the residual stress, microstructure, mechanical properties and corrosion resistance of welded joints were studied. Results show the stress state of the weld and the surrounding area was effectively improved by the pneumatic chipping hammer and ultrasonic peening treatment, and the residual stress field of the surface layer changed from tensile stress to compressive stress. On the contrary, low-temperature stress relieving annealing had no obvious effect on stress distribution. After the pneumatic chipping hammer and ultrasonic peening treatment, the welded joints were machined and hardened. Correspondingly, strength and hardness were improved. However, the heat treatment only led to a slight decrease in strength and hardness due to the static recovery of the welded joint structure. All stress relief methods effectively improved the corrosion resistance of welded joints, with the ultrasonic peening treatment giving the best performance.

Research on Microstructure and Properties of Welded Joint of 2205 Steel with FCAW

2011 ◽  
Vol 391-392 ◽  
pp. 763-767
Author(s):  
Li Yang ◽  
Na Zhang
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Duplex Stainless Steel ◽  
Base Metal ◽  
Heat Affected Zone ◽  
Welded Joint ◽  
High Strength ◽  
Two Phase ◽  
Flux Cored Arc Welding ◽  
Mechanical Properties And Corrosion

On the basis of the analysis of composition, microstructure, properties and weldability of 2205 duplex stainless steel, the flux cored arc welding (FCAW) process is made. Then the microstructure, mechanical properties and corrosion resistance of welded joint were analyzed. The results shows using FCAW process, in order to obtain high strength, perfect impact toughness and overall and partial resistance to stress corrosion in welded joint, the Ni content of duplex stainless steel welding material should be 2% to 4% higher than that of base metal, multi-layer and multi-channel welding is adopted with the strict control of energy input less than or equal to 0.926KJ/mm, layer temperature is less than 120 °C, thus the appropriate proportion of two-phase structure in the welded joint can be got. Using a reasonable welding procedure, the microstructure in weld beam is austenite (A) + ferrite (F), and in heat affected zone is ferrite (F) + austenite (A) + a small amount of third phase, the content of austenite in weld beam and heat affected zone is higher than that of the base metal. Tensile strength of the welded joint is up to 854.5MPa and the fracture occurs in the base metal and the heat affected zone. The welded joint has high strength, good plasticity, toughness and corrosion resistance.

Precipitation condition and effect of volume fraction on corrosion properties of secondary phase on casted super-duplex stainless steel UNS S32750

2019 ◽  
Vol 66 (1) ◽  
pp. 61-66 ◽  
Author(s):  
Byung-Hyun Shin ◽  
Dohyung Kim ◽  
Sanghyup Park ◽  
Myungwon Hwang ◽  
Junghyun Park ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Grain Boundary ◽  
Duplex Stainless Steel ◽  
Corrosion Behavior ◽  
Volume Fraction ◽  
Secondary Phase ◽  
Super Duplex Stainless Steel ◽  
Precipitation Condition ◽  
Content Type

Purpose The secondary phase decreased the corrosion resistance because of the segregation of Cr and Mo. Therefore, this paper aims to study the precipitation condition and the effect of secondary phase with volume fraction on corrosion behavior. Design/methodology/approach Secondary phase precipitated approximately from 375°C to 975°C because of saturated Cr and Mo at grain boundary by growth of austenite. Therefore, heat treatment from 800°C to 1,300°C was applied to start the precipitation of the secondary phase. Findings The secondary phase is precipitated at 1,020°C because of segregation by heterogeneous austenite. The growth of austenite at 1,000°C needs the time to saturate the Cr and Mo at grain boundary. When the volume fraction of austenite is 56 per cent (14 min at 1,000°C), the secondary phase is precipitated with grain boundary of austenite. The secondary phase increased the current density (corrosion rate) and decreased the passivation. That is checked to the critical pitting temperature (CPT) curves. The 1 per cent volume fraction of secondary phase decreased CPT to 60°C from 71°C. Research limitations/implications The precipitation of secondary phase not wants anyone. Casted super-duplex stainless steel (SDSS) of big size precipitates the secondary phase. This study worked the precipitation condition and the suppression conditions of secondary phase. Social implications Manufacturers need precipitation condition to make high-performance SDSS. Originality/value The corrosion resistance of SDSS is hard the optimization because SDSS is dual-phase stainless steel. The precipitation of the secondary phase must be controlled to optimize of the corrosion resistance of SDSS. Anyone not studied the precipitation condition of secondary phase and the effect of secondary phase with volume fraction on corrosion behavior of SDSS.

Microstructural evolution and mechanical integrity relationship of dissimilar metal welding between 2205 duplex stainless steel and composite bimetallic plates

2021 ◽  
pp. 095440622110036
Author(s):  
Changqing Ye ◽  
Weiguo Zhai ◽  
Guangyao Lu ◽  
Qingsong Liu ◽  
Liang Ni ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Weld Metal ◽  
Duplex Stainless Steel ◽  
Intergranular Corrosion ◽  
Thermal Cycle ◽  
Filler Metal ◽  
2205 Duplex Stainless Steel ◽  
Welding Thermal Cycle ◽  
Intergranular Corrosion Resistance

In this paper, shielded metal arc welding on the dissimilar joint between 2205 duplex stainless steel and composite bimetallic plates (304 L stainless steel/10CrNi3MoV steel) with a filler metal E2209 was performed. Furthermore, the microstructure, phase, mechanical properties and intergranular corrosion resistance of the joints were investigated and element distributions of the interfaces were characterized. The results show that austenite transformed to ferrite under the influence of welding thermal cycle, and then a large amount of ferrite appeared in heat affected zone (HAZ) of 2205 duplex stainless steel. Coarse bainite grains were formed in HAZ of the 10CrNi3MoV steel near the fusion line with high temperature welding thermal cycle. Fine granular bainite was also generated in HAZ of 10CrNi3MoV steel due to the relatively short exposure time to the active temperature of grain growth. Local peak temperature near the base 10CrNi3MoV steel was still high enough to recrystallize the 10CrNi3MoV steel to form partial-recrystallization HAZ due to phase change. The filler metal was compatible with the three kinds of base materials. The thickness of the elemental diffusion interfaces layers was about 100 µm. The maximum microhardness value was obtained in the HAZ of 2205 duplex stainless steel (287 ± 14 HV), and the minimum one appeared in HAZ of SS304L (213 ± 5 HV). The maximum tensile strength of the welded joint was about 670 ± 6 MPa, and the tensile specimens fractured in ductile at matrix of the composite bimetallic plates. The impact energy of the weld metal and HAZ of the 10CrNi3MoV steel tested at –20 °C were 274 ± 6 J and 308 ± 5 J, respectively. Moreover, the intergranular corrosion resistance of the weldment including 304 L stainless steel, weld metal, HAZs and 2205 duplex stainless steel was in good agreement with the functional design requirements of materials corrosion resistance.

Corrosion Resistance Evaluation of a Stainless-Steel Brazed Joint in HCl Solution

2021 ◽  
Vol 1016 ◽  
pp. 997-1002
Author(s):  
Hikaru Nagata ◽  
Masa Ono ◽  
Yasuyuki Miyazawa ◽  
Yuji Hayashi ◽  
Yoshio Bizen
Keyword(s):  
Aqueous Solution ◽  
Stainless Steel ◽  
Corrosion Resistance ◽  
Base Metal ◽  
Corrosion Behavior ◽  
Anodic Polarization ◽  
Filler Metal ◽  
Brazed Joint ◽  
In Situ Observations

To clarify the effect of the acid solution type on corrosion resistance, the corrosion behavior of stainless steel brazed joints in HCl aqueous solution was evaluated through electrochemical measurements. Anodic polarization curves of a ferritic stainless-steel base metal, Ni-based brazing filler metals, and a brazed joint were recorded. In addition, in situ observations were conducted to observe the corrosion behavior of each structure of the brazed joint. Corrosion potentials of the brazing filler metal were lower than that of the base metal. In situ observations of the brazed joint revealed the order of corrosion in aqueous hydrochloric acid. According to the electrochemical measurements, under an actual corrosive environment, the brazing filler metal can function as an anode and selectively corrode. In addition, the anodic polarization curve of the brazed joint showed values between those of the polarization curves of the brazing filler metal and the base metal, indicating that the corrosion resistance could be electrochemically evaluated in HCl aqueous solution.

Effect of rolling deformation on microstructure and mechanical properties of 2205 duplex stainless steel with micro-nano structure

2020 ◽  
Vol 34 (25) ◽  
pp. 2050269
Author(s):  
Yuqi Mao ◽  
Yuehong Zheng ◽  
Yu Shi ◽  
Min Zhu ◽  
Saitejin ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Duplex Stainless Steel ◽  
Volume Fraction ◽  
Two Phase ◽  
Corrosion Properties ◽  
Nano Structure ◽  
2205 Duplex Stainless Steel ◽  
Microstructure And Mechanical Properties ◽  
Rolling Deformation

In order to further expand the application scope of 2205 duplex stainless steel (DSS), its microstructure and mechanical properties require as much attention as its corrosion properties. In this study, 2205DSSs were prepared by aluminothermic reaction and the microstructures and mechanical behavior of the rolled alloys were analyzed. The micro-nanocrystals composite structure appears in the alloys after rough rolling with deformation of 40% at [Formula: see text]C followed by finishing rolling with deformation of 30%, 50% and 70% at [Formula: see text]C. With the increase of rolling deformation, the two-phase structure is gradually elongated, the average size of the two-phase grains is gradually increased, and some [Formula: see text] phase will change to [Formula: see text] phase, the volume fraction of [Formula: see text] phase is gradually increased, and the distribution of nanocrystals is gradually uniform. Meanwhile, the fracture mode of alloy is gradually changed from ductile fracture to brittle fracture. The strength and hardness of the alloy increase gradually.

Sign in / Sign up

Export Citation Format

Share Document