Synthesis, characterization and finite element analysis of polypropylene composite reinforced by jute and carbon fiber

2021 ◽  
Author(s):  
Sunil Kumar Tiwari ◽  
Akula Umamaheswara Rao ◽  
Naresh Reddy ◽  
Harsh Sharma ◽  
Jitendra Kumar Pandey
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Carbon Fiber ◽  
Polypropylene Composite ◽  
Element Analysis

scholarly journals Finite Element Analysis for Nonlinear Unbonded Circular Fiber-Reinforced Elastomeric Bearings

2021 ◽  
Vol 5 (7) ◽  
pp. 170
Author(s):  
Pablo Castillo Ruano ◽  
Alfred Strauss
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Carbon Fiber ◽  
Seismic Isolation ◽  
Nonlinear Viscoelasticity ◽  
Fiber Reinforcement ◽  
Special Focus ◽  
Fiber Reinforced ◽  
Element Analysis ◽  
Elastomeric Bearings

In recent years, interest in low-cost seismic isolation systems has increased. The replacement of the steel reinforcement in conventional elastomeric bearings for a carbon fiber reinforcement is a possible solution and has garnered increasing attention. To investigate the response of fiber-reinforced elastomeric bearings (FREBs) under seismic loads, it is fundamental to understand its mechanical behavior under combined vertical and horizontal loads. An experimental investigation of the components presents complexities due to the high loads and displacements tested. The use of a finite element analysis can save time and resources by avoiding partially expensive experimental campaigns and by extending the number of geometries and topologies to be analyzed. In this work, a numerical model for carbon fiber-reinforced bearings is implemented, calibrated, and validated and a set of virtual experiments is designed to investigate the behavior of the bearings under combined compressive and lateral loading. Special focus is paid to detailed modeling of the constituent materials. The elastomeric matrix is modeled using a phenomenological rheological model based on the hyperelastic formulation developed by Yeoh and nonlinear viscoelasticity. The model aims to account for the hysteretic nonlinear hyper-viscoelastic behavior using a rheological formulation that takes into consideration hyperelasticity and nonlinear viscoelasticity and is calibrated using a series of experiments, including uniaxial tension tests, planar tests, and relaxation tests. Special interest is paid to capturing the energy dissipated in the unbonded fiber-reinforced elastomeric bearing in an accurate manner. The agreement between the numerical results and the experimental data is assessed, and the influence of parameters such as shape factor, aspect ratio, vertical pressure, and fiber reinforcement orientation on stress distribution in the bearings as well as in the mechanical properties is discussed.

The Study on Carbon Fiber Reinforced Concrete Beams Based on Finite Element Analysis

2012 ◽  
Vol 430-432 ◽  
pp. 331-336
Author(s):  
Jian Hua Wang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Reinforced Concrete ◽  
Carbon Fiber ◽  
Concrete Beams ◽  
Fiber Reinforced Concrete ◽  
Reinforced Concrete Beams ◽  
Fiber Reinforced ◽  
Element Analysis ◽  
Carbon Fiber Reinforced

Carbon fiber-reinforced polymer (CFRP) sheets have recently become popular for use as repair or rehabilitation material for deteriorated carbon fiber reinforced concrete structures. Carbon fiber reinforced concrete beams were analyzed by finite element software ANASYS. Through the finite element analysis, the results showed that using bonded CFRP to strengthen R. C. beams can significantly increase their load carrying capacity. However, the beams with prestressed CFRP can withstand larger ultimate loads than beams with bonded CFRP. Using bonded CFRP to strengthen R. C. beams can obviously reduce the ultimate deflection.

Design Optimization of Driveshaft and Universal Joint Using Finite Element Technique

2016 ◽  
Author(s):  
Mosfequr Rahman ◽  
Gustavo Molina ◽  
Sirajus Salekeen ◽  
Ana Dungan ◽  
Isaac Hyers ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Carbon Fiber ◽  
Safety Factor ◽  
Material Properties ◽  
Moment Of Inertia ◽  
Outer Diameter ◽  
Element Analysis ◽  
Numerical Experimentation ◽  
Universal Joints

Finite Element Analysis (FEA) has been performed on variety of a driveshaft and universal joints based on different shaft materials and shaft different operating angles. A driveshaft is particularly useful in applications such as taking of transferring torque from one piece of equipment to the other such as in vehicle of all kinds. A driveshaft transfers torque from the transmission to the rear end differential since these two pieces of equipment cannot be connected directly. The driveshaft has universal joints located on both ends of the shaft to allow for fluctuations in the angle of the transmission and rear differential. The driveshaft alone is composed of two parts, a female and male end, connected by a spline to allow changes in the length during operation. The driveshaft must be able to withstand the constant torque that is being applied throughout operation in order to increase safety for the operator and machine. Having a lower polar moment of inertia allows the driveshaft to turn with a lower torque value compared to a driveshaft with a higher moment of inertia. It is noted that driveshaft can be manufactured into a variety of lengths and diameters depending on the use and equipment it will be supporting. This paper describes a method of finite element implemented on variations of driveshaft and universal joints. Effect of material properties, geometry and operating angle of the driveshaft were considered for this numerical investigation. Five different materials such as structural steel, aluminum alloy, polyethylene, titanium, and carbon fiber with an outer diameter of 1.5 in of the driveshaft was used for this analysis. The effect of both metals and composite materials was observed. Based on the analysis it was found that a 15° operating angle allowed for the longest life cycle of the driveshaft, while the carbon fiber composite presented the highest stress resistance and safety factor, approximately 6 GPa of yield tensile strength and a safety factor of 15. It was also found that titanium had an equivalent safety factor of 15. However, the tensile yield strength of titanium was much lower than that of its composite counterpart. All of the numerical experimentation was done using the Finite Element Analysis software ANSYS. Material properties for all materials were preset in the software except the composite carbon fiber whose properties were easily found from other research papers and experiments. Based on the data collected and the general assumptions that the most effective drive shaft is the one that lasts the longest. It can be concluded that a driveshaft made of carbon fiber operating at an angle of 15° presents the optimum driveshaft design.

Sign in / Sign up

Export Citation Format

Share Document