Energy density for signals maximizing the integral-square error

Measurement ◽  
2016 ◽  
Vol 90 ◽  
pp. 224-232 ◽  
Author(s):  
Krzysztof Tomczyk ◽  
Edward Layer
Keyword(s):  
Energy Density ◽  
Integral Square Error

Fine-scale taxonomic and temporal variability in the energy density of invertebrate prey of juvenile Chinook salmon Oncorhynchus tshawytscha

2020 ◽  
Vol 655 ◽  
pp. 185-198
Author(s):  
J Weil ◽  
WDP Duguid ◽  
F Juanes
Keyword(s):  
Energy Density ◽  
Chinook Salmon ◽  
Temporal Variability ◽  
Energy Content ◽  
Single Point ◽  
Single Species ◽  
Fine Scale ◽  
Temporal Differences ◽  
Juvenile Chinook Salmon ◽  
Juvenile Chinook

Variation in the energy content of prey can drive the diet choice, growth and ultimate survival of consumers. In Pacific salmon species, obtaining sufficient energy for rapid growth during early marine residence is hypothesized to reduce the risk of size-selective mortality. In order to determine the energetic benefit of feeding choices for individuals, accurate estimates of energy density (ED) across prey groups are required. Frequently, a single species is assumed to be representative of a larger taxonomic group or related species. Further, single-point estimates are often assumed to be representative of a group across seasons, despite temporal variability. To test the validity of these practices, we sampled zooplankton prey of juvenile Chinook salmon to investigate fine-scale taxonomic and temporal differences in ED. Using a recently developed model to estimate the ED of organisms using percent ash-free dry weight, we compared energy content of several groups that are typically grouped together in growth studies. Decapod megalopae were more energy rich than zoeae and showed family-level variability in ED. Amphipods showed significant species-level variability in ED. Temporal differences were observed, but patterns were not consistent among groups. Bioenergetic model simulations showed that growth rate of juvenile Chinook salmon was almost identical when prey ED values were calculated on a fine scale or on a taxon-averaged coarse scale. However, single-species representative calculations of prey ED yielded highly variable output in growth depending on the representative species used. These results suggest that the latter approach may yield significantly biased results.

A HIGH ENERGY DENSITY ZINC/OXYGEN BATTERY SYSTEM

1966 ◽  
Author(s):  
S. CHODOSH ◽  
E. KATSOULIS ◽  
M. ROSANSKY
Keyword(s):  
Energy Density ◽  
High Energy ◽  
High Energy Density ◽  
Battery System

Efficient Co-Harvesting of Solar Energy and Low-Grade Heat by Molecular Photoswitches for High Energy Density, Long-Term Stable Solar Thermal Battery

2019 ◽  
Author(s):  
Zhao-Yang Zhang ◽  
Tao LI
Keyword(s):  
Energy Density ◽  
Solar Energy ◽  
High Performance ◽  
High Energy ◽  
Solar Thermal ◽  
High Energy Density ◽  
Low Grade ◽  
Thermal Battery ◽  
Low Grade Heat

Solar energy and ambient heat are two inexhaustible energy sources for addressing the global challenge of energy and sustainability. Solar thermal battery based on molecular switches that can store solar energy and release it as heat has recently attracted great interest, but its development is severely limited by both low energy density and short storage stability. On the other hand, the efficient recovery and upgrading of low-grade heat, especially that of the ambient heat, has been a great challenge. Here we report that solar energy and ambient heat can be simultaneously harvested and stored, which is enabled by room-temperature photochemical crystal-to-liquid transitions of small-molecule photoswitches. The two forms of energy are released together to produce high-temperature heat during the reverse photochemical phase change. This strategy, combined with molecular design, provides high energy density of 320-370 J/g and long-term storage stability (half-life of about 3 months). On this basis, we fabricate high-performance, flexible film devices of solar thermal battery, which can be readily recharged at room temperature with good cycling ability, show fast rate of heat release, and produce high-temperature heat that is >20<sup> o</sup>C higher than the ambient temperature. Our work opens up a new avenue to harvest ambient heat, and demonstrate a feasible strategy to develop high-performance solar thermal battery.

Efficient Co-Harvesting of Solar Energy and Low-Grade Heat by Molecular Photoswitches for High Energy Density, Long-Term Stable Solar Thermal Battery

2019 ◽  
Author(s):  
Zhao-Yang Zhang ◽  
Tao LI
Keyword(s):  
Energy Density ◽  
Solar Energy ◽  
High Performance ◽  
High Energy ◽  
Solar Thermal ◽  
High Energy Density ◽  
Low Grade ◽  
Thermal Battery ◽  
Low Grade Heat

Solar energy and ambient heat are two inexhaustible energy sources for addressing the global challenge of energy and sustainability. Solar thermal battery based on molecular switches that can store solar energy and release it as heat has recently attracted great interest, but its development is severely limited by both low energy density and short storage stability. On the other hand, the efficient recovery and upgrading of low-grade heat, especially that of the ambient heat, has been a great challenge. Here we report that solar energy and ambient heat can be simultaneously harvested and stored, which is enabled by room-temperature photochemical crystal-to-liquid transitions of small-molecule photoswitches. The two forms of energy are released together to produce high-temperature heat during the reverse photochemical phase change. This strategy, combined with molecular design, provides high energy density of 320-370 J/g and long-term storage stability (half-life of about 3 months). On this basis, we fabricate high-performance, flexible film devices of solar thermal battery, which can be readily recharged at room temperature with good cycling ability, show fast rate of heat release, and produce high-temperature heat that is >20<sup> o</sup>C higher than the ambient temperature. Our work opens up a new avenue to harvest ambient heat, and demonstrate a feasible strategy to develop high-performance solar thermal battery.

The Study of ESD Destructive Mechanism for PN-Junction

1996 ◽  
Author(s):  
N. Wakai ◽  
M. TsuTsumi ◽  
T. Setoya
Keyword(s):  
Energy Density ◽  
Thermal Diffusion ◽  
Electric Discharge ◽  
Intermediate Region ◽  
Human Body Model ◽  
Machine Model ◽  
Pn Junction ◽  
Special Cases ◽  
Equilibrium Region

Abstract Mechanism of destruction caused by electrostatic discharge of PN junction was examined from two viewpoints; classification of destruction mode with consideration to destructive energy density, and comparison of destruction shape. Destructive energy density of PN junction was calculated based on Speakman model, and destruction mode was classified by Wunsch-Bell plot. As a result of Wunsch-Bell plot, electric discharge which occur at low resistance, for example machine model (MM: C∙R = 200pF ∙ 0Ω), resulted in adiabatic destruction that does not involve thermal diffusion. With electric discharge at high resistance, for example human body model (HBM: C∙R = 100pF ∙ 1500Ω), excessive destruction in intermediate region that involves thermal diffusion, and depending on the device, destruction at equilibrium region were proven to be reproducible. In case of MM, (adiabatic region destruction) destruction was confirmed in a wide extent of the joint part, but in case of HBM (intermediate region destruction) destruction was confirmed near the center of the joint part. From this fact, it was found that by verifying the places of destruction and their shapes, although in special cases, it is possible to know the destruction mode when destruction occurs.

Sign in / Sign up

Export Citation Format

Share Document