Methanol permeability and proton conductivity of sulfonated co-polyimide membranes

2005 ◽  
Vol 258 (1-2) ◽  
pp. 115-122 ◽  
Author(s):  
K OKAMOTO ◽  
Y YIN ◽  
O YAMADA ◽  
M ISLAM ◽  
T HONDA ◽  
...  
Keyword(s):  
Proton Conductivity ◽  
Methanol Permeability ◽  
Polyimide Membranes

scholarly journals PEMBUATAN DAN KARAKTERISASI MEMBRAN KOMPOSIT KITOSAN-SODIUM ALGINAT TERFOSFORILASI SEBAGAI PROTON EXCHANGE MEMBRANE FUEL CELL (PEMFC)

2016 ◽  
Vol 1 (1) ◽  
pp. 14
Author(s):  
Siti Wafiroh ◽  
Suyanto Suyanto ◽  
Yuliana Yuliana
Keyword(s):  
Fuel Cell ◽  
Sodium Alginate ◽  
Proton Conductivity ◽  
Composite Membrane ◽  
Proton Exchange Membrane ◽  
Proton Exchange ◽  
Methanol Permeability ◽  
Water Swelling ◽  
Exchange Membrane

AbstrakDi era globalisasi ini, kebutuhan bahan bakar fosil semakin meningkat dan ketersediannya semakin menipis. Oleh karena itu, dibutuhkan bahan bakar alternatif seperti Proton Exchange Membrane Fuel Cell (PEMFC). Tujuan dari penelitian ini adalah membuat dan mengkarakterisasi membran komposit kitosan-sodium alginat dari rumput laut coklat (Sargassum sp.) terfosforilasi sebagai Proton Exchange Membrane Fuel Cell (PEMFC). PEM dibuat dengan 4 variasi perbandingan konsentrasi antara kitosan dengan sodium alginat 8:0, 8:1, 8:2, dan 8:4 (b/b). Membran komposit kitosan-sodium alginat difosforilasi dengan STPP 2N. Karakterisasi PEM meliputi: uji tarik, swelling air, kapasitas penukar ion, FTIR, SEM, permeabilitas metanol, dan konduktivitas proton. Berdasarkan hasil analisis tersebut, membran yang optimal adalah perbandingan 8:1 (b/b) dengan nilai modulus young sebesar 0,0901 kN/cm2, swelling air sebesar 19,14 %, permeabilitas metanol sebesar 72,7 x 10-7, dan konduktivitas proton sebesar 4,7 x 10-5 S/cm. Membran komposit kitosan-sodium alginat terfosforilasi memiliki kemampuan yang cukup baik untuk bisa diaplikasikan sebagai membran polimer elektrolit dalam PEMFC. Kata kunci: kitosan, sodium alginat, terfosforilasi, PEMFC  AbstractIn this globalization era, the needs of fossil fuel certainly increases, but its providence decreases. Therefore, we need alternative fuels such as Proton Exchange Membrane Fuel Cell (PEMFC). The purpose of this study is preparationand characterization of phosphorylated chitosan-sodium alginate composite membrane from brown seaweed (Sargassum sp.) as Proton Exchange Membrane Fuel Cell (PEMFC). PEM is produced with 4 variations of concentration ratio between chitosan and sodium alginate 8:0, 8:1, 8:2, and 8:4 (w/w). Chitosan-sodium alginate composite membrane phosphorylated with 2 N STPP. The characterization of PEM include: tensile test, water swelling, ion exchange capacity, FTIR, SEM, methanol permeability, and proton conductivity. Based on the analysis result, the optimal membrane is ratio of 8:1 (w/w) with the value of Young’s modulus about 0.0901 kN/cm2, water swelling at 19.14%, methanol permeability about 72.7 x 10-7, and proton conductivity about 4.7 x 10-5 S/cm. The phosphorylated chitosan-sodium alginate composite membrane has good potentials for the application of the polymer electrolyte membrane in PEMFC. Keywords: chitosan, sodium alginate, phosphorylated, PEMFC

Highly selective sulfonated Poly (arylene ether nitrile) composite membranes containing copper phthalocyanine grafted graphene oxide for direct methanol fuel cell

2021 ◽  
pp. 095400832110394
Author(s):  
Yan Ma ◽  
Kaixu Ren ◽  
Ziqiu Zeng ◽  
Mengna Feng ◽  
Yumin Huang
Keyword(s):  
Graphene Oxide ◽  
Proton Conductivity ◽  
Direct Methanol Fuel Cells ◽  
Copper Phthalocyanine ◽  
Composite Membranes ◽  
Proton Exchange ◽  
Methanol Permeability ◽  
Arylene Ether ◽  
Direct Methanol ◽  
Sulfonated Poly

To improve the performances of sulfonated poly (arylene ether nitrile) (SPEN)–based proton exchange membranes (PEMs) in direct methanol fuel cells (DMFCs), the copper phthalocyanine grafted graphene oxide (CP-GO) was successfully prepared via in situ polymerization and subsequently incorporated into SPEN as filler to fabricate a series of SPEN/CP-GO-X (X represents for the mass ratio of CP-GO) composite membranes. The water absorption, swelling ratio, mechanical properties, proton conductivity, and methanol permeability of the membranes were systematically studied. CP-GO possesses good dispersion and compatibility with SPEN matrix, which is propitious to the formation of strong interfacial interactions with the SPEN, so as to provide more efficient transport channels for proton transfer in the composite membranes and significantly improve the proton conductivity of the membranes. Besides, the strong π–π conjugation interactions between CP-GO and SPEN matrix can make the composite membranes more compact, blocking the methanol transfer in the membranes, and significantly reducing the methanol permeability. Consequently, the SPEN/CP-GO-1 composite membrane displayed outstanding tensile strength (58 MPa at 100% RH and 25°C), excellent proton conductivity (0.178 S cm−1 at 60°C), and superior selectivity (5.552 × 105 S·cm−3·s). This study proposed a new method and strategy for the preparation of high performance PEMs.

scholarly journals Surface-modified fibrous membranes for fuel cell application

2019 ◽  
Vol 90 ◽  
pp. 01005
Author(s):  
Noor Fatina Emelin Nor Fadzil ◽  
Ebrahim Abouzari-Lotf ◽  
Mohan V. Jacob ◽  
Nurfatehah Wahyuny Che Jusoh ◽  
Arshad Ahmad
Keyword(s):  
Fuel Cell ◽  
Proton Conductivity ◽  
Composite Membrane ◽  
Barrier Layer ◽  
Methanol Permeability ◽  
Low Permeability ◽  
Membrane Selectivity ◽  
Fuel Cell Application ◽  
Fibrous Membranes ◽  
Surface Modified

Low permeability layers of poly(1-vinylimidazole) were polymerised and deposited onto both sides of electrospun polyethersulfone (PES) nanofibrous sheet radiofrequency plasma. The layers not only act as an efficient fuel barrier layer but also impart high and stable proton conductivity, as well as better chemical and dimensional stabilities. Typically, the composite membrane exhibited methanol permeability as low as 33.20 x 10-8 cm2 s-1 and high through-plane proton conductivity of 52.4 mS cm-1 at 95% RH, indicating membrane selectivity of 0.675 x 108 mS.s cm-3, which is approximately 33 times greater than the selectivity of N115 under similar conditions.

scholarly journals Composite Sulfonated Polyether-Ether Ketone Membranes with SBA-15 for Electrochemical Energy Systems

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1570 ◽  
Author(s):  
A. Rico-Zavala ◽  
J. L. Pineda-Delgado ◽  
A. Carbone ◽  
A. Saccà ◽  
E. Passalacqua ◽  
...  
Keyword(s):  
Proton Conductivity ◽  
Proton Exchange Membrane ◽  
Energy Systems ◽  
Composite Membranes ◽  
Exchange Capacity ◽  
Proton Exchange ◽  
Inorganic Materials ◽  
Methanol Permeability ◽  
Ether Ketone ◽  
Electrochemical Energy

The aim of this work is the evaluation of a Sulfonated Poly Ether-Ether Ketone (S-PEEK) polymer modified by the addition of pure Santa Barbara Amorphous-15 (SBA-15, mesoporous silica) and SBA-15 previously impregnated with phosphotungstic acid (PWA) fillers (PWA/SBA-15) in order to prepare composite membranes as an alternative to conventional Nafion® membranes. This component is intended to be used as an electrolyte in electrochemical energy systems such as hydrogen and methanol Proton Exchange Membrane Fuel Cell (PEMFC) and Electrochemical Hydrogen Pumping (EHP). The common requirements for all the applications are high proton conductivity, thermomechanical stability, and fuel and oxidant impermeability. The morphology of the composite membranes was investigated by Scanning Electron Microscopy- Energy Dispersive X-ray Spectroscopy (SEM-EDS) analysis. Water Uptake (Wup), Ion Exchange Capacity (IEC), proton conductivity, methanol permeability and other physicochemical properties were evaluated. In PEMFC tests, the S-PEEK membrane with a 10 wt.% SBA-15 loading showed the highest performance. For EHP, the inclusion of inorganic materials led to a back-diffusion, limiting the compression capacity. Concerning methanol permeability, the lowest methanol crossover corresponded to the composites containing 5 wt.% and 10 wt.% SBA-15.

Preparation of High Performance SPEEK/Cloisite 15A Nanocomposite Membrane via Advanced Membrane Formulation Method

2014 ◽  
Vol 70 (2) ◽  
Author(s):  
Juhana Jaafar ◽  
A. F. Ismail ◽  
T. Matsuura ◽  
M. H. D. Othman ◽  
Mukhlis A. Rahman ◽  
...  
Keyword(s):  
Proton Conductivity ◽  
Polymer Matrix ◽  
High Performance ◽  
Morphological Structure ◽  
Nanocomposite Membrane ◽  
Methanol Permeability ◽  
Solution Intercalation ◽  
High Proton ◽  
Poly Ether Ether Ketone ◽  
Cloisite 15A

Sulfonated poly (ether ether ketone) (SPEEK)/Cloisite 15A® nanocomposite membranes were prepared via solution intercalation method. For better dispersion of nanoclay in the polymer matrix, the solution intercalation method was modified and a compatibilizer was introduced. The state of nanoclay dispersion was determined by FESEM. The effect of the solution formulation preparation method and compatibilizer on the performance properties such as proton conductivity and methanol permeability of all membranes was studied. FESEM analysis confirmed that SPEEK/Cloisite 15A® nanocomposite membrane prepared via modified solution intercalation method and in the presence of compatibilizer was the best membrane in terms of its morphological structure. Due to its well nanoclay distribution in polymer matrix, this kind of membrane exhibited the highest selectivity owing to its high proton conductivity and low methanol permeability. SPEEK/Cloisite 15A® with compatibilizer prepared via modified solution intercalation method was found to be the best membrane. 

A highly proton-conducting, methanol-blocking Nafion composite membrane enabled by surface-coating crosslinked sulfonated graphene oxide

2016 ◽  
Vol 52 (10) ◽  
pp. 2173-2176 ◽  
Author(s):  
Guangwei He ◽  
Xueyi He ◽  
Xinglin Wang ◽  
Chaoyi Chang ◽  
Jing Zhao ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Oxide Film ◽  
Proton Conductivity ◽  
Composite Membrane ◽  
Surface Coating ◽  
Nafion Membrane ◽  
Methanol Permeability ◽  
High Proton Conductivity ◽  
High Proton ◽  
Sulfonated Graphene

Coating an ultrathin graphene oxide film onto a Nafion membrane confers a distinct anti-tradeoff behavior: 93% decrease of methanol permeability while retaining the high proton conductivity.

Hybrid polymers based on sulfonated polynorbornene with enhanced proton conductivity for direct methanol fuel cells

2012 ◽  
Vol 24 (8) ◽  
pp. 756-764 ◽  
Author(s):  
Rong Zeng ◽  
Shuqin Xiao ◽  
Lie Chen ◽  
Yiwang Chen
Keyword(s):  
Proton Conductivity ◽  
Direct Methanol Fuel Cells ◽  
Sol Gel ◽  
Weight Ratio ◽  
Proton Exchange ◽  
Methanol Permeability ◽  
Relative Humidity Condition ◽  
Conduction Pathway ◽  
Direct Methanol ◽  
Order Of Magnitude

Sulfonated polynorbornene (SPNB) and 3-aminopropyltriethoxysilane (KH550) hybrid cross-linked proton exchange membranes doped with different weight ratio of phosphotungstic acid (PWA) were prepared by a simple sol-gel process. The cross-linked structures led to low methanol permeability and good stability of the nanocomposites. Incorporation of PWA has significantly improved the proton conductivity of the hybrid membrane due to an extra provided conductive proton-conduction pathway to facilitate proton transportation. In particular, the conductivity of SPNB/KH550/PWA25 reached the maximum of 0.02 S.cm−1 at 80°C under the 100% relative humidity condition, and this value is on the same order of magnitude as that of Nafion117. Furthermore, SPNB /KH550/PWA20 owns the lowest proton transport activation energy (8.39 kJ.mol−1).

Sign in / Sign up

Export Citation Format

Share Document