Development of a plastic collapse assessment procedure in the p–M diagram method for pipe bends with a local thin area under combined internal pressure and external in-plane bending moment

2012 ◽  
Vol 247 ◽  
pp. 42-57 ◽  
Author(s):  
Kenji Oyamada ◽  
Shinji Konosu ◽  
Takashi Ohno
Keyword(s):  
Internal Pressure ◽  
Bending Moment ◽  
Assessment Procedure ◽  
Plastic Collapse ◽  
Diagram Method ◽  
Plane Bending ◽  
Collapse Assessment

Plastic Collapse Assessment Procedure in P-M Diagram Method for Pipe Bends With a Local Thin Area Under Combined Pressure and Out-of-Plane Bending Moment

2012 ◽  
Author(s):  
Kenji Oyamada ◽  
Shinji Konosu ◽  
Takashi Ohno
Keyword(s):  
Internal Pressure ◽  
Pressure Ratio ◽  
Bending Moment ◽  
Piping System ◽  
Assessment Procedure ◽  
Plastic Collapse ◽  
Diagram Method ◽  
Out Of Plane ◽  
Plane Bending ◽  
Collapse Assessment

Pipe bends are common elements in piping system such as power or process piping, and local thinning are typically occurred on pipe bends due to erosion or corrosion. Therefore, it is important to establish the plastic collapse condition for pipe bends having a local thin area (LTA) under combined internal pressure and external bending moment. In this paper, a simplified plastic collapse assessment procedure in p-M (internal pressure ratio and external bending moment ratio) diagram method for pipe bends with a local thin area simultaneously subjected to internal pressure, p, and external out-of-plane bending moment, M, due to earthquake, etc., is proposed, which is derived from the reference stress. In this paper, only cases of that an LTA is located in the crown of pipe bends are considered. The plastic collapse loads derived from the p-M diagram method are compared with the results of both experiments and FEA for pipe bends of the same size with various configurations of an LTA.

Procedure for Plastic Collapse Assessment of a Local Thin Area Near Vessel and Nozzle Intersections Subjected to Internal Pressure and External Loadings

2015 ◽  
Author(s):  
Shinji Konosu ◽  
Kenta Ogasawara ◽  
Kenji Oyamada
Keyword(s):  
Internal Pressure ◽  
Critical Region ◽  
Pressure Ratio ◽  
Branch Pipe ◽  
Bending Moment ◽  
Plastic Collapse ◽  
Element Analysis ◽  
Diagram Method ◽  
External Moment ◽  
Collapse Assessment

This paper develops a procedure for plastic collapse assessment of vessel (run pipe) - nozzle (branch pipe) intersections with an arbitrarily positioned local thin area (LTA) under different loading conditions, namely internal pressure, external moment on a nozzle applied along various directions with respect to the vessel main axis, and pure bending moment on a vessel. Although simplified procedures for plastic collapse assessment based on the p-M (internal pressure ratio and external bending moment ratio) diagram method have been previously proposed for straight cylindrical vessels and pipe bends with an LTA, very few studies have dealt with the determination of plastic collapse load for an LTA in the critical region of intersecting vessels subjected to internal pressure and external moment loading. This is likely due to the complexity of the stresses caused by the applied loads in the critical region, which arises from geometric discontinuities. In this paper, simple and empirical formulae for predicting conservative plastic collapse loads for an LTA in the critical region of the intersecting vessels are proposed based on the analytical results of stresses at defect-free vessel-nozzle intersections by using linear finite element analysis (FEA). Localized elastic stress retardation factors are taken into account in the evaluation by the results of a non-linear FEA. Consequently, a p-M diagram method is developed for application to vessel-nozzle intersections with an LTA.

Development of Simplified Plastic Collapse Assessment Procedure for Vessel With Internal Surface Flaw

2007 ◽  
Author(s):  
Shinji Konosu ◽  
Kenji Oyamada
Keyword(s):  
Internal Pressure ◽  
Bending Moment ◽  
Internal Surface ◽  
Outer Radius ◽  
Surface Flaw ◽  
Assessment Procedure ◽  
Plastic Collapse ◽  
Diagram Method ◽  
Surface Flaws ◽  
And Storage

A simplified assessment procedure using the p-M diagram, which can evaluate the plastic collapse load for pressure equipment such as vessels, piping and storage tanks with an internal surface flaw simultaneously subjected to internal pressure, p, and external bending moment, M, due to earthquake, etc., is derived by taking into account the influence of internal pressure acting on the flaw surface. For an internal surface flaw subjected to pressure, the already-proposed p-M diagram for an external flaw can be applied if the parameters for an internal surface flaw proposed in this paper are used. And the plastic collapse loads derived from the p-M diagram method are being verified by comparison with experimental results. It has been clarified that the parameters for internal surface flaws are also the same as those for external surface flaws where the ratio of thickness to outer radius of a vessel is significantly smaller than unity and internal pressure is small.

Development of Simplified Plastic Collapse Assessment Procedure for Elbow With an External Surface Flaw Simultaneously Subjected to Internal Pressure and External Bending Moment

2008 ◽  
Author(s):  
Kenji Oyamada ◽  
Shinji Konosu
Keyword(s):  
Internal Pressure ◽  
External Surface ◽  
Pressure Ratio ◽  
Bending Moment ◽  
Cylindrical Part ◽  
Surface Flaw ◽  
Assessment Procedure ◽  
Plastic Collapse ◽  
Diagram Method ◽  
The Status

A simplified assessment procedure using the p-M (internal pressure ratio and external bending moment ratio) diagram, which can evaluate the plastic collapse load for an elbow with an external surface flaw simultaneously subjected to internal pressure, p, and external bending moment, M, due to earthquake, etc., is derived. The p-M diagram evaluation is an easy way to visualize the status of components with a flaw. For an elbow with an external surface flaw, the already-proposed p-M diagram by one of authors for the cylindrical part of pressure equipment such as vessels, pipes, etc. with a surface flaw can be applied if the parameters proposed in this paper are used. The plastic collapse loads derived from the p-M diagram method are being verified by comparison with existing experimental and FEA results.

Validity of Assessment Procedure in p-M Method for Multiple Volumetric Flaws

2008 ◽  
Author(s):  
Shinji Konosu ◽  
Masato Kano ◽  
Norihiko Mukaimachi ◽  
Shinichiro Kanamaru
Keyword(s):  
Internal Pressure ◽  
Yield Stress ◽  
Bending Moment ◽  
Pressure Vessels ◽  
Assessment Procedure ◽  
Plastic Collapse ◽  
Storage Tanks ◽  
Collapse Load ◽  
The Status ◽  
Single Flaw

General components such as pressure vessels, piping, storage tanks and so on are designed in accordance with the construction codes based on the assumption that there are no flaws in such components. There are, however, numerous instances in which in-service single or multiple volumetric flaws (local thin areas; volumetric flaws) are found in the equipment concerned. Therefore, it is necessary to establish a Fitness for Service (FFS) rule, which is capable of judging these flaws. The procedure for a single flaw or multiple flaws has recently been proposed by Konosu for assessing the flaws in the p–M (pressure-moment) Diagram, which is an easy way to visualize the status of the component with flaws simultaneously subjected to internal pressure, p and external bending moment, M due to earthquake, etc. If the assessment point (Mr, pr) lies inside the p–M line, the component with flaws is judged to be safe. In this paper, numerous experiments and FEAs for a cylinder with external multiple volumetric flaws were conducted under (1) pure internal pressure, (2) pure external bending moment, and (3) subjected simultaneously to both internal pressure and external bending moment, in order to determine the plastic collapse load at volumetric flaws by applying the twice-elastic slope (TES) as recommended by ASME. It has been clarified that the collapse (TES) loads are much the same as those calculated under the proposed p–M line based on the measured yield stress.

Plastic Collapse Assessment Procedure for Vessel With Local Thin Area Simultaneously Subjected to Internal Pressure and External Bending Moment

2006 ◽  
Author(s):  
Shinji Konosu ◽  
Norihiko Mukaimachi
Keyword(s):  
Internal Pressure ◽  
Pressure Ratio ◽  
Bending Moment ◽  
Outer Diameter ◽  
Assessment Procedure ◽  
Plastic Collapse ◽  
Moment Ratio ◽  
Tension And Compression ◽  
And Storage ◽  
Moment Ratio Diagram

Assessment of the local thin area should be undertaken for both tension and compression bending. In this paper, simplified reference stresses for a flaw in a cylinder are proposed. By using these results, a newly-developed p-M (internal pressure ratio and external bending moment ratio) diagram which can evaluate the plastic collapse condition for pressure equipment such as vessels, piping and storage tanks with a local thin area simultaneously subjected to internal pressure, p, and external bending moment, M, due to earthquake, etc. is proposed. The p-M line is verified by comparison with the FEA results and the numerous results of experiment for a cylinder with a volumetric flaw obtained through the reference literatures. It was clarified that the differences in plastic collapse limit between the p-M line and DNV guideline under both internal pressure and compression moment became evident where the outer diameter/wall thickness of a cylinder is large and the yield ratio of the material is small.

Effect of Bend Angle on Gross Plastic Deformation of Pipe Bends for Out-of-Plane Bending: A Study Using Plastic Work Curvature Method

2016 ◽  
Author(s):  
Anindya Bhattacharya ◽  
Sachin Bapat ◽  
Hardik Patel ◽  
Shailan Patel ◽  
Michael P. Cross
Keyword(s):  
Plastic Deformation ◽  
Internal Pressure ◽  
Bending Moment ◽  
Plastic Work ◽  
Bend Angle ◽  
Piping System ◽  
Plastic Collapse ◽  
Pipe Bend ◽  
Out Of Plane ◽  
Plane Bending

Bends are an integral part of a piping system. Because of the ability to ovalize and warp they offer more flexibility when compared to straight pipes. Piping Code ASME B31.3 [1] provides flexibility factors and stress intensification factors for pipe bends. Like any other piping component, one of the failure mechanisms of a pipe bend is gross plastic deformation. In this paper, plastic collapse load of pipe bends have been analyzed for various bend parameters (bend parameter = tRbrm2) under internal pressure and out-of-plane bending moment for various bend angles using both small and large deformation theories. FE code ABAQUS version 6.9EF-1 has been used for the analyses. The goal of the paper is to develop an expression for plastic collapse moment for a bend using plastic work curvature method when the bend is subjected to out-of-plane bending moment and internal pressure as a function of bend angle and bend parameter.

Validity of Assessment Procedure in p-M Method for Multiple Volumetric Flaws

2010 ◽  
Vol 132 (2) ◽  
Author(s):  
Shinji Konosu ◽  
Masato Kano ◽  
Norihiko Mukaimachi ◽  
Shinichiro Kanamaru
Keyword(s):  
Internal Pressure ◽  
Bending Moment ◽  
Pressure Vessels ◽  
Assessment Procedure ◽  
Plastic Collapse ◽  
Storage Tanks ◽  
Collapse Load ◽  
Element Analysis ◽  
The Status ◽  
Single Flaw

General components such as pressure vessels, piping, storage tanks, and so on are designed in accordance with the construction codes based on the assumption that there are no flaws in such components. There are, however, numerous instances in which in-service single or multiple volumetric flaws such as local thin areas are found in the equipment concerned. Therefore, it is necessary to establish a fitness for service rule, which is capable of evaluating these flaws. The procedure for a single flaw or multiple flaws has recently been proposed for assessing the flaws in the p-M (pressure-moment) diagram, which is an easy way to visualize the status of the component with flaws simultaneously subjected to internal pressure p and external bending moment M due to earthquake, etc. If the assessment point (Mr,pr) lies inside the p-M line, the component with flaws is judged to be safe. In this paper, numerous experiments and finite element analysis for a cylinder with external multiple volumetric flaws were conducted under (1) pure internal pressure, (2) pure external bending moment, and (3) subjected simultaneously to both internal pressure and external bending moment, in order to determine the plastic collapse load at volumetric flaws by applying the twice-elastic slope (TES) as recommended by ASME. It has been clarified that the collapse (TES) loads are much the same as those calculated under the proposed p-M line based on the measured yield stress.

Development of Plastic Collapse Assessment Procedure for Cylindrical Vessels With a Local Thin Area Near a Nozzle Under Internal Pressure

2013 ◽  
Author(s):  
Kenji Oyamada ◽  
Shinji Konosu ◽  
Tadashi Horibe ◽  
Kenta Ogasawara ◽  
Tetsuji Miyashita ◽  
...  
Keyword(s):  
Stress State ◽  
Stress Concentration ◽  
Internal Pressure ◽  
Pressure Vessels ◽  
Assessment Procedure ◽  
Plastic Collapse ◽  
Stress Concentrations ◽  
Nozzle Hole ◽  
Stress Concentration Factors ◽  
Collapse Assessment

There are numerous cases where a local thin area has found near a nozzle attachment in cylindrical pressure vessels. Since the stress concentration due to a nozzle hole under internal pressure significantly affect to the stress state of the vessel near the nozzle, it must be taken into account in its plastic collapse assessment. In this paper, a new plastic collapse assessment procedure for cylindrical vessels with a local thin area near a nozzle attachment under internal pressure was proposed. This proposal utilizes the existing reference stresses to estimate the plastic collapse load under three-axial condition derived in accordance with the Tresca theory. The distribution of stress concentrations in vessel wall due to a nozzle attachment depends on its reinforcement condition for the nozzle hole, so the stress state should be computed by linear FEA in advance. The stress concentration factors are provided with normalizing of generated stresses in vessels near a nozzle attachment for the similar type of dimensions, orientations and projections of the nozzle attachment by the computed stresses with already-proposed equations for no reinforcement conditions. The plastic collapse loads predicted by the proposed reference stress are ascertained with the results of experiments and non-linear FEA.

Sign in / Sign up

Export Citation Format

Share Document