Case Report: An Eyelid Nodule Caused by Candidatus Dirofilaria hongkongensis Diagnosed by Mitochondrial 12S rRNA Sequence

ABSTRACT. A 59-year-old female living in Rayong Province, eastern Thailand, presented with painless, right upper eyelid nodule for 3 months. Upon removal of the eyelid mass, a well-circumscribed, firm globular mass with diameter about 1 cm was found. Histopathological examination revealed an immature female dirofilarial worm reminiscent of Dirofilaria repens, characterized by prominent sharp longitudinal ridges at external surface of the cuticle. Analysis of the mitochondrial 12S rRNA sequence showed that the worm belongs to Candidatus Dirofilaria hongkongensis. It is likely that some infections previously reported as D. repens based on histological examination may have actually been due to Candidatus D. hongkongensis.

1D alignment of proteins and other nanoparticles by using reversible covalent bonds on cyclic peptide nanotubes

Self-assembling cyclic peptide nanotubes are supramolecular structures whose diameter and external surface properties are precisely controlled. In this communication we describe a general strategy to align different molecules on top...

Topography of the location of mental foramen in dried edentulous human mandible and its clinical implication

The mental foramen is an oval or round opening on external surface of mandible and transmits mental nerve and vessels. Mostly located at apex of second mandibular premolar or between the apices of premolars. The study was commenced on 60 dried edentulous mandibles with the aim to determine location of mental foramen(MF) with reference to surrounding anatomical landmarks. By measuring its distance from midline (symphysis menti), posterior border of ramus of mandible, lower border of mandible. Length of lower border (Base) of mandible was also measured. In present study most common shape of mental foramen was round (70%). The mean distances of MF from midline are 24.36mm on right side and 24.15mm left side. From posterior border of ramus are 64.45mm on right side and 64.15mm on left side. From base of mandible are 12.29mm on right side and 12.48mm on left side. Length of base mandible (midline to angle of mandible) is 83.27mm right side and 83.12mm left side. Ratio of distance from symphysis menti to MF and length of base of mandible are same on both sides that are 0.29. There is statistically significant positive correlation between distance from symphysis menti to MF and length of base of mandible.The MF plays a very important role in treatment planning and its location needs to be considered prior to placement of dental-implants, regional anesthesia, osteotomy-surgeries and during complete denture-fabrication in order to avoid MN injury and related complications.

External surface water influence on explosive eruption dynamics, with implications for stratospheric sulfur delivery and volcano-climate feedback

Explosive volcanic eruptions can inject sulfur dioxide (SO2) into the stratosphere to form aerosol particles that modify Earth’s radiation balance and drive surface cooling. Eruptions involving interactions with shallow layers (< 500 m) of surface water and ice modify the eruption dynamics that govern the delivery of SO2 to the stratosphere. External surface water potentially controls the evolution of explosive eruptions in two ways that are poorly understood: (1) by modulating the hydrostatic pressure within the conduit and at the vent, and (2) through the ingestion and mixing of external water, which governs fine ash production as well as eruption column buoyancy flux. To make progress, we couple one-dimensional models of magma flow in the conduit and atmospheric column rise through a novel ”magma-water interaction” model that simulates the occurrence, extent and consequences of water entrainment depending on the depth of a surface water layer. We explore the effects of hydrostatic pressure on magma ascent in the conduit and gas decompression at the vent, and the conditions for which water entrainment drives fine ash production by quench fragmentation, eruption column collapse, or outright failure of the jet to breach the water surface. We show that the efficiency of water entrainment into the jet is the predominant control on jet behavior. For an increase in water depth of 50 to 100 m, the critical magma mass eruption rate required for eruption columns to reach the tropopause increases by an order of magnitude. Finally, we estimate that enhanced emission of fine ash leads to up to a 2-fold increase in the mass flux of particles < 125 microns to spreading umbrella clouds, together with up to a 10-fold increase in water mass flux, conditions that can enhance the removal of SO2 via chemical scavenging and ash sedimentation. Overall, compared to purely magmatic eruptions, we suggest that hydrovolcanic eruptions will be characterized by a reduced delivery of SO2 to the stratosphere. Our results thus suggest the possibility of an unrecognized volcano-climate feedback mechanism arising from modification of volcanic climate forcing by direct interaction of erupting magma with varying distributions of water and ice at the Earth’s surface.

Research Part Surface Position Influence on Metal Removal and Steady-State Roughness During Vibro-Abrasive Processing

The paper is devoted to the study of part surface position and its influence on metal removal and steady-state rougness during vibro-abrasive processing. The article raises the differences between vibro-abrasive processing of external and internal part surfaces. Theoretical dependencies analysis for determination on part material removal and surface steady-state roughness is carried out. It is known that available theoretical dependencies do not take into account part surface position for material removal and the steady-state roughness calculation. Experimental researches to determine internal surface material removal with external surface isolation were carried out. The influence of part surface position on the steady-state roughness is investigated. Based on obtained experimental results, the dependence graphs of material removal and roughness on the processing time are constructed. The comparative analysis of the part surface position influence on material removal and the steady-state roughness during vibro-abrasive processing is carried out. The results showed that material removal volume from the internal surface more than from the external for short part length, however material removal volume from the external surfaces grows significantly in case of part length increasing, while from the internal surfaces is not significant. It is established that the internal surface steady-state roughness is ∼1.55 times higher than external surface steady-state roughness after processing in triangular prism 15×15, grit 16.