Determining anisotropic elastic parameters of transversely isotropic rocks through single torsional shear test and theoretical analysis

2018 ◽  
Vol 169 ◽  
pp. 184-199 ◽  
Author(s):  
Yota Togashi ◽  
Mamoru Kikumoto ◽  
Kazuo Tani
2021 ◽  
Vol 40 (4) ◽  
pp. 267-276
Author(s):  
Peter Mesdag ◽  
Leonardo Quevedo ◽  
Cătălin Tănase

Exploration and development of unconventional reservoirs, where fractures and in-situ stresses play a key role, call for improved characterization workflows. Here, we expand on a previously proposed method that makes use of standard isotropic modeling and inversion techniques in anisotropic media. Based on approximations for PP-wave reflection coefficients in orthorhombic media, we build a set of transforms that map the isotropic elastic parameters used in prestack inversion into effective anisotropic elastic parameters. When used in isotropic forward modeling and inversion, these effective parameters accurately mimic the anisotropic reflectivity behavior of the seismic data, thus closing the loop between well-log data and seismic inversion results in the anisotropic case. We show that modeling and inversion of orthorhombic anisotropic media can be achieved by superimposing effective elastic parameters describing the behavior of a horizontally stratified medium and a set of parallel vertical fractures. The process of sequential forward modeling and postinversion analysis is exemplified using synthetic data.


Author(s):  
Christoph Oefner ◽  
Elena Riemer ◽  
Kerstin Funke ◽  
Michael Werner ◽  
Christoph-Eckhard Heyde ◽  
...  

AbstractIn biomechanics, large finite element models with macroscopic representation of several bones or joints are necessary to analyze implant failure mechanisms. In order to handle large simulation models of human bone, it is crucial to homogenize the trabecular structure regarding the mechanical behavior without losing information about the realistic material properties. Accordingly, morphology and fabric measurements of 60 vertebral cancellous bone samples from three osteoporotic lumbar spines were performed on the basis of X-ray microtomography (μCT) images to determine anisotropic elastic parameters as a function of bone density in the area of pedicle screw anchorage. The fabric tensor was mapped in cubic bone volumes by a 3D mean-intercept-length method. Fabric measurements resulted in a high degree of anisotropy (DA = 0.554). For the Young’s and shear moduli as a function of bone volume fraction (BV/TV, bone volume/total volume), an individually fit function was determined and high correlations were found (97.3 ≤ R2 ≤ 99.1,p < 0.005). The results suggest that the mathematical formulation for the relationship between anisotropic elastic constants and BV/TV is applicable to current μCT data of cancellous bone in the osteoporotic lumbar spine. In combination with the obtained results and findings, the developed routine allows determination of elastic constants of osteoporotic lumbar spine. Based on this, the elastic constants determined using homogenization theory can enable efficient investigation of human bone using finite element analysis (FEA).


Author(s):  
Justin M. Deuerling ◽  
Weimin Yue ◽  
Alejandro A. Espinoza ◽  
Ryan K. Roeder

The elastic constants of cortical bone are orthotropic or transversely isotropic depending on the anatomic origin of the tissue. Micromechanical models have been developed to predict anisotropic elastic properties from structural information. Many have utilized microstructural features such as osteons, cement lines and Haversian canals to model the tissue properties [1]. Others have utilized nanoscale features to model the mineralized collagen fibril [2]. Quantitative texture analysis using x-ray diffraction techniques has shown that elongated apatite crystals exhibit a preferred orientation in the longitudinal axis of the bone [3]. The orientation distribution of apatite crystals provides fundamental information influencing the anisotropy of the extracellular matrix (ECM) but has not been utilized in existing micromechanical models.


Geophysics ◽  
1996 ◽  
Vol 61 (5) ◽  
pp. 1245-1246

Okoye et al. develop a least-squares iterative inversion technique determining of the elastic parameters δ* and vertical P-wave velocity (α0) of any transversely isotropic modeling material in the laboratory. The anisotropic inverse modeling technique finds the best fitting solution and implements analytical rather than numerical differentiations to optimize the accuracy of the results.


Géotechnique ◽  
2011 ◽  
Vol 61 (9) ◽  
pp. 809-814 ◽  
Author(s):  
S. YIMSIRI ◽  
K. SOGA

Geophysics ◽  
2007 ◽  
Vol 72 (3) ◽  
pp. S133-S138 ◽  
Author(s):  
Tianfei Zhu ◽  
Samuel H. Gray ◽  
Daoliu Wang

Gaussian-beam depth migration is a useful alternative to Kirchhoff and wave-equation migrations. It overcomes the limitations of Kirchhoff migration in imaging multipathing arrivals, while retaining its efficiency and its capability of imaging steep dips with turning waves. Extension of this migration method to anisotropic media has, however, been hampered by the difficulties in traditional kinematic and dynamic ray-tracing systems in inhomogeneous, anisotropic media. Formulated in terms of elastic parameters, the traditional anisotropic ray-tracing systems aredifficult to implement and inefficient for computation, especially for the dynamic ray-tracing system. They may also result inambiguity in specifying elastic parameters for a given medium.To overcome these difficulties, we have reformulated the ray-tracing systems in terms of phase velocity.These reformulated systems are simple and especially useful for general transversely isotropic and weak orthorhombic media, because the phase velocities for these two types of media can be computed with simple analytic expressions. These two types of media also represent the majority of anisotropy observed in sedimentary rocks. Based on these newly developed ray-tracing systems, we have extended prestack Gaussian-beam depth migration to general transversely isotropic media. Test results with synthetic data show that our anisotropic, prestack Gaussian-beam migration is accurate and efficient. It produces images superior to those generated by anisotropic, prestack Kirchhoff migration.


Geophysics ◽  
2012 ◽  
Vol 77 (4) ◽  
pp. B197-B206 ◽  
Author(s):  
Douglas E. Miller ◽  
Steve A. Horne ◽  
John Walsh

Dipole sonic log data recorded in a vertical pilot well and the associated production well are analyzed over a [Formula: see text]-ft section of a North American gas shale formation. The combination of these two wells enables angular sampling in the vertical direction and over a range of inclination angles from 54° to 90°. Dipole sonic logs from these wells show that the formation’s average properties are, to a very good approximation, explained by a transversely isotropic medium with a vertical symmetry axis and with elastic parameters satisfying [Formula: see text], but inconsistent with the additional ANNIE relation ([Formula: see text]). More importantly, these data clearly show that, at least for fast anisotropic formations such as this gas shale, sonic logs measure group slownesses for propagation with the group angle equal to the borehole inclination angle. Conversely, the data are inconsistent with an interpretation that they measure phase slownesses for propagation with the phase angle equal to the borehole inclination angle.


Sign in / Sign up

Export Citation Format

Share Document