Enhancing PV Cell’s electrical efficiency using phase change material with copper foam matrix and multi-walled carbon nanotubes as passive cooling method

2020 ◽  
Vol 160 ◽  
pp. 663-675 ◽  
Author(s):  
Abdulmunem R. Abdulmunem ◽  
Pakharuddin Mohd Samin ◽  
Hasimah Abdul Rahman ◽  
Hashim A. Hussien ◽  
Izhari Izmi Mazali
Keyword(s):  
Carbon Nanotubes ◽  
Phase Change ◽  
Phase Change Material ◽  
Passive Cooling ◽  
Electrical Efficiency ◽  
Copper Foam ◽  
Cooling Method ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes ◽  
Change Material

scholarly journals The Effect of Hydroxylated Multi-Walled Carbon Nanotubes on the Properties of Peg-Cacl2 Form-Stable Phase Change Materials

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1403
Author(s):  
Lingyu Zheng ◽  
Xuelai Zhang ◽  
Weisan Hua ◽  
Xinfeng Wu ◽  
Fa Mao
Keyword(s):  
Thermal Conductivity ◽  
Carbon Nanotubes ◽  
Phase Change ◽  
Phase Change Material ◽  
Phase Change Materials ◽  
Interfacial Thermal Resistance ◽  
Stable Phase ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes ◽  
Change Material

Calcium ions can react with polyethylene glycol (PEG) to form a form-stable phase change material, but the low thermal conductivity hinders its practical application. In this paper, hydroxylated multi-walled carbon nanotubes (MWCNTs) with different mass are introduced into PEG1500·CaCl2 form-stable phase change material to prepare a new type of energy storage material. Carbon nanotubes increased the mean free path (MFP) of phonons and effectively reduced the interfacial thermal resistance between pure PEG and PEG1500·CaCl2 3D skeleton structure. Thermal conductivity was significant improved after increasing MWCNTs mass, while the latent heat decreases. At 1.5 wt%, composite material shows the highest phase change temperature of 42 °C, and its thermal conductivity is 291.30% higher than pure PEG1500·CaCl2. This article can provide some suggestions for the preparation and application of high thermal conductivity form-stable phase change materials.

scholarly journals Latent Heat Thermal Storage of Nano-Enhanced Phase Change Material Filled by Copper Foam with Linear Porosity Variation in Vertical Direction

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1508
Author(s):  
Mohammad Ghalambaz ◽  
Mohammad Shahabadi ◽  
S. A. M Mehryan ◽  
Mikhail Sheremet ◽  
Obai Younis ◽  
...  
Keyword(s):  
Natural Convection ◽  
Phase Change ◽  
Phase Change Material ◽  
Metal Foam ◽  
Vertical Direction ◽  
Melting Time ◽  
Copper Foam ◽  
Average Porosity ◽  
The Impact ◽  
Change Material

The melting flow and heat transfer of copper-oxide coconut oil in thermal energy storage filled with a nonlinear copper metal foam are addressed. The porosity of the copper foam changes linearly from bottom to top. The phase change material (PCM) is filled into the metal foam pores, which form a composite PCM. The natural convection effect is also taken into account. The effect of average porosity; porosity distribution; pore size density; the inclination angle of enclosure; and nanoparticles’ concentration on the isotherms, melting maps, and the melting rate are investigated. The results show that the average porosity is the most important parameter on the melting behavior. The variation in porosity from 0.825 to 0.9 changes the melting time by about 116%. The natural convection flows are weak in the metal foam, and hence, the impact of each of the other parameters on the melting time is insignificant (less than 5%).

Numerical Thermal Performance Investigation of an Electric Motor Passive Cooling System Employing Phase Change Materials

2021 ◽  
Author(s):  
Ali Deriszadeh ◽  
Filippo de Monte ◽  
Marco Villani
Keyword(s):  
Phase Change ◽  
Phase Change Material ◽  
Electric Motor ◽  
Phase Change Materials ◽  
Cooling System ◽  
Passive Cooling ◽  
Time Step ◽  
Cooling Performance ◽  
Passive Cooling System ◽  
Change Material

Abstract This study investigates the cooling performance of a passive cooling system for electric motor cooling applications. The metal-based phase change materials are used for cooling the motor and preventing its temperature rise. As compared to oil-based phase change materials, these materials have a higher melting point and thermal conductivity. The flow field and transient heat conduction are simulated using the finite volume method. The accuracy of numerical values obtained from the simulation of the phase change materials is validated. The sensitivity of the numerical results to the number of computational elements and time step value is assessed. The main goal of adopting the phase change material based passive cooling system is to maintain the operational motor temperature in the allowed range for applications with high and repetitive peak power demands such as electric vehicles by using phase change materials in cooling channels twisted around the motor. Moreover, this study investigates the effect of the phase change material container arrangement on the cooling performance of the under study cooling system.

Sign in / Sign up

Export Citation Format

Share Document