Creep behavior in a γ′ strengthened Co–Al–W–Ta–Ti single-crystal alloy at 1000 °C

2015 ◽  
Vol 97 ◽  
pp. 37-40 ◽  
Author(s):  
F. Xue ◽  
H.J. Zhou ◽  
Q.Y. Shi ◽  
X.H. Chen ◽  
H. Chang ◽  
...  
Keyword(s):  
Single Crystal ◽  
Creep Behavior ◽  
Single Crystal Alloy

scholarly journals Study on the Creep Behavior of a Ni3Al-Based Single Crystal Alloy at 850°C/450 MPa

2020 ◽  
Vol 2020 ◽  
pp. 1-7
Author(s):  
Liwu Jiang ◽  
Yu Yang ◽  
Meiling Wu ◽  
Min Cai
Keyword(s):  
Fracture Surface ◽  
Single Crystal ◽  
Creep Behavior ◽  
Creep Deformation ◽  
Fracture Mechanism ◽  
Crystal Orientation ◽  
Fracture Morphology ◽  
Cutting Mechanism ◽  
Single Crystal Alloy ◽  
Fracture Morphologies

The creep behaviors of Ni3Al-based single crystal alloy IC6SX with [001] and [111] orientations under the condition of 850°C/450 MPa were investigated. The effect of crystal orientation on the creep lives, fracture morphology, fracture mechanism, and dislocation evolution of the alloys with different orientations was analyzed systematically. The results showed that the creep lives of the alloy were closely related to the crystal orientation under the condition of 850°C/450 MPa. The creep lives of the single crystal alloys with [001] and [111] orientations were 56.3 h and 126.9 h, respectively. Moreover, the fracture morphologies of the two alloys with [001] and [111] orientations were different. The results showed that some holes formed at the fracture surface of the alloy with [111] rather than [001] orientation. Furthermore, the surface near the fracture of the two alloys with [001] and [111] orientations was serrated. Therefore, the fracture mechanism of the single crystal alloys with [001] and [111] orientations was ductile fracture. In addition, a large number of dislocations cut into the γ ′ phase. Therefore, the cutting mechanism of dislocations in the alloys with [001] and [111] orientations was the creep deformation mechanism.

scholarly journals Effect of Stress on Creep Behavior of Single Crystal Alloy IC6SX at 980°C

2020 ◽  
Vol 2020 ◽  
pp. 1-5
Author(s):  
Liwu Jiang ◽  
Xuezheng Dou ◽  
Meiling Wu
Keyword(s):  
Single Crystal ◽  
Creep Behavior ◽  
Steady State Creep Rate ◽  
Creep Life ◽  
Creep Experiment ◽  
Dislocation Glide ◽  
Single Crystal Alloy ◽  
Higher Temperature ◽  
And Diffusion ◽  
Mixed Mechanism

Ni3Al-based single crystal alloy IC6SX was prepared by seed crystal method. The effect of different stress conditions on creep behavior of this alloy at 980°C was investigated. The results showed that the creep life of this alloy at 980°C decreased significantly with the increase of stress. When the stress increased from 180 MPa to 230 MPa, the creep life dropped from 245.5 h to 69.3 h, and the steady-state creep rate increased slightly but not significantly. Meanwhile, the morphology of γ ′ phase and dislocation after creep were studied. The results showed that with the increase of stress, the density of dislocations in the γ ′ phase increased gradually, the strength of this alloy decreased gradually, so the creep life decreased significantly. The Y-NiMo phase resolved from the γ phase decreased gradually as the creep life decreased. The creep experiment of the alloy was carried out at 980°C. Due to the higher temperature, the diffusion of atoms in this alloy became faster. Deformation was not only caused by the slippage of dislocations in the crystal but also by the diffusion of atoms. Therefore, the creep mechanism of single crystal alloy IC6SX at this temperature is a mixed mechanism of dislocation glide and diffusion.

scholarly journals Influences of Holes Arrangement on Creep Characteristic of Nickel-Base Single Crystal Alloy Blade Cooling Holes

2013 ◽  
Vol 2013 ◽  
pp. 1-5
Author(s):  
Lei Li ◽  
Liangbo Ao ◽  
Gongnan Xie ◽  
Xinmei Wang ◽  
Gang Cao
Keyword(s):  
Single Crystal ◽  
Creep Behavior ◽  
Film Cooling ◽  
Horizontal Distance ◽  
Blade Cooling ◽  
Single Crystal Alloy ◽  
Creep Time ◽  
Creep Characteristic ◽  
Cooling Technology ◽  
Nickel Base

Film cooling technology is developed to enhance the temperature resistant of nickel-base single crystal alloy blade. The shape, dimension, and arrangement of cooling holes impact the blade strength and life grievously. In this paper, the influences of holes arrangement on creep characteristic of cooling holes in the plate sample are investigated. The constitutive model for creep considering both cavitation and degradation damage is developed to predict the creep behavior of cooling holes. Results show that there are stress interferences among cooling holes. The distance and radius of the cooling holes impact the creep behavior of cooling holes seriously. Decreasing horizontal distance of the holes results in creep time reducing. On the contrary, increasing the vertical distance of the holes makes the creep time reduced.

scholarly journals Creep behavior of a novel Co-Al-W-base single crystal alloy containing Ta and Ti at 982∘C

2014 ◽  
Vol 14 ◽  
pp. 15002 ◽  
Author(s):  
Fei Xue ◽  
Haijing Zhou ◽  
Xuhua Chen ◽  
Qianying Shi ◽  
Hai Chang ◽  
...  
Keyword(s):  
Single Crystal ◽  
Creep Behavior ◽  
Single Crystal Alloy

CMSX-2

Alloy Digest ◽  
1992 ◽  
Vol 41 (11) ◽  
Keyword(s):  
Physical Properties ◽  
Single Crystal ◽  
Alloy Development ◽  
Single Crystal Alloy ◽  
High Level

Abstract CMSX-2 is a single crystal alloy development of Cannon-Muskegon Corporation designed to achieve a high level of balanced properties. This datasheet provides information on composition, physical properties, as well ascreep and fatigue. Filing Code: Ni-417. Producer or source: Cannon-Muskegon Corporation.

Sign in / Sign up

Export Citation Format

Share Document