scholarly journals Passenger exposure to respiratory aerosols in a train cabin: Effects of window, injection source, output flow location

2021 ◽  
pp. 103280
Author(s):  
Mahdi Ahmadzadeh ◽  
Mehrzad Shams
Keyword(s):  
2012 ◽  
Vol 625 ◽  
pp. 117-120
Author(s):  
Hui Xu ◽  
Xiao Hong Chen

The liquid phase experiment is finished ,and the relation curve of input- pressure and input-flow、output-flow、distributary rate are worked out.We are bout to calculate the production capacity and define the best distribution rate of the operation parameters.At the same time , the solid-liquid phase separating experiment are made too and we conclude the relation curve of input-pressure and consistency 、separating efficiency .Comparing with the numerical simulation ,the result is reasonable.


1992 ◽  
Vol 73 (2) ◽  
pp. 427-433 ◽  
Author(s):  
Z. Hantos ◽  
A. Adamicza ◽  
E. Govaerts ◽  
B. Daroczy

In nine anesthetized and paralyzed cats, the mechanical impedances of the total respiratory system (Zrs) and the lungs (ZL) were measured with small-volume pseudorandom forced oscillations between 0.2 and 20 Hz. ZL was measured after thoracotomy, and chest wall impedance (Zw) was calculated as Zw = Zrs-ZL. All impedances were determined by using input airflow [input impedance (Zi)] and output flow measured with a body box [transfer impedance (Zt)]. The differences between Zi and Zt were small for Zrs and negligible for ZL. At 0.2 Hz, the real and imaginary parts of ZL amounted to 33 +/- 4 and 35 +/- 3% (SD), respectively, of Zrs. Up to 8 Hz, all impedances were consistent with a model containing a frequency-independent resistance and inertance and a constant-phase tissue part (G-jH)/omega alpha, where G and H are coefficients for damping and elastance, respectively, omega is angular frequency, and alpha determines the frequency dependence of the real and imaginary parts. G/H was higher for Zw than for ZL (0.29 +/- 0.05 vs. 0.22 +/- 0.04, P less than 0.01). In four cats, the amplitude dependence of impedances was studied: between oscillation volumes of 0.8 and 3 ml, GL, HL, Gw, and Hw decreased on average by 3, 9, 26, and 29%, respectively, whereas the change in G/H was small for both ZL (7%) and Zw (-4%). The values of H were two to three times higher than the quasistatic elastances estimated with greater volume changes (greater than 20 ml).


1987 ◽  
Vol 131 (1) ◽  
pp. 137-157
Author(s):  
D. F. HOULIHAN ◽  
C. AGNISOLA ◽  
N. M. HAMILTON ◽  
I. TRARA GENOINO

A technique is described which allowed the measurement of the oxygen consumption of the isolated heart of Octopus vulgaris. Contraction of the heart resulted in an aortic output and a flow through the heart muscle into coronary veins (the coronary output). The flow and oxygen content of the aortic output and the coronary output were measured with variable input pressures and constant output back pressure (volume loaded), variable output back pressure and constant aortic output (pressure loaded), and during hypoxia. Volume loading of the heart resulted in an increase in aortic output, power output and total oxygen consumption. Pressure loading increased power output and total oxygen consumption of the heart. Exposure to hypoxia decreased the aortic output, power output and total cardiac oxygen consumption. In the response of the heart to reduced work, brought about either by a reduced input pressure or by hypoxic perfusate, the power output was linearly related to the total oxygen consumption of the heart. The oxygen extracted from the coronary output accounted for 80–100% of the total oxygen consumption of the heart. Coronary output amounted to 30% of the total cardiac output at maximum power output. In volume-loaded hearts the volume of the coronary output increased as aortic output increased; in pressure-loaded hearts coronary output increased as power output increased, but aortic output remained constant. In hypoxia, the coronary output increased as the aortic output fell. At a perfusate Po2 of around 50 Torr (1 Torr = 133 Pa), the aortic output ceased although the heart continued to beat and the coronary output continued, accounting for all of the oxygen consumption of the heart. The coronary output flow in vitro therefore has the capacity to be varied independently of the aortic output flow to maintain the oxygen supply to the perfused cardiac muscle.


1981 ◽  
Vol 73 (1) ◽  
pp. 3-8
Author(s):  
Ventura Bengoechea ◽  
David W. Hendricks ◽  
Roger E. Krempel

2005 ◽  
Vol 21 (2) ◽  
pp. 159-166 ◽  
Author(s):  
H. Landry ◽  
E. Piron ◽  
J. M. Agnew ◽  
C. Laguë ◽  
M. Roberge
Keyword(s):  

2018 ◽  
Vol 224 ◽  
pp. 04021
Author(s):  
Vadim Kopp ◽  
Alexey Balakin ◽  
Natalya Balakina ◽  
Mikhail Zamoryonov

Questions related to the management of the process of multiple measurements are considered, depending on the result, which affects their number. In this case, the measurement time can be significantly increased. The above algorithm for controlling the measurement process justifies the random nature of the duration of its execution, which entails the need to study the time of carrying out multiple measurements. The paper constructs a semi-Markov model that allows to determine the distribution functions of time between events in the output flow of products after measurements, which makes it possible to dock this model with models of elements of higher levels of the hierarchy of the production structure. In the model, it is taken into account that some part of the production after a given number of measurements is defective and leaves the system. The constructed semi-Markov model allows to predict the performance of a technical system associated with multiple measurements.


Author(s):  
Guozhong Cao ◽  
Haixia Guo ◽  
Runhua Tan

To match for complex product function and to solve insufficient computer aid for functional design, the Extended-Effect driven Function-Behavior-Structure (EE-FBS) model is constructed. A multi-flow and multi-pole effect model is presented by extending the one with single input/output flow in TRIZ. Four effect patterns and three reasoning methods are proposed to create effect chains. The FBS model is extended to an EE-FBS model based on effect through the description of the law of mapping overall function to external behavior, from external behavior to sub-behavior, etc. A functional design process was presented based on the EE-FBS model, and the computer-aided functional design software system is developed. A design example for functional design of Chinese dropping pill medicine demonstrates the proposed method is feasible.


Sign in / Sign up

Export Citation Format

Share Document