Compressive stress-strain model of cold-formed circular hollow section stub columns considering local buckling

2017 ◽  
Vol 120 ◽  
pp. 495-505 ◽  
Author(s):  
Chang Yang ◽  
Hua Zhao ◽  
Yuping Sun ◽  
Shichun Zhao
Keyword(s):  
Compressive Stress ◽  
Local Buckling ◽  
Stress Strain ◽  
Hollow Section ◽  
Circular Hollow Section ◽  
Strain Model ◽  
Stub Columns

scholarly journals Stress–strain relationship model of glulam bamboo under axial loading

2020 ◽  
Vol 29 ◽  
pp. 2633366X2095872
Author(s):  
Yang Wei ◽  
Mengqian Zhou ◽  
Kunpeng Zhao ◽  
Kang Zhao ◽  
Guofen Li
Keyword(s):  
Tensile Stress ◽  
Compressive Stress ◽  
Failure Modes ◽  
Axial Loading ◽  
Tensile Failure ◽  
Stress Strain ◽  
Laminated Bamboo ◽  
Bamboo Scrimber ◽  
Strain Relationship ◽  
Strain Model

Glulam bamboo has been preliminarily explored for use as a structural building material, and its stress–strain model under axial loading has a fundamental role in the analysis of bamboo components. To study the tension and compression behaviour of glulam bamboo, the bamboo scrimber and laminated bamboo as two kinds of typical glulam bamboo materials were tested under axial loading. Their mechanical behaviour and failure modes were investigated. The results showed that the bamboo scrimber and laminated bamboo have similar failure modes. For tensile failure, bamboo fibres were ruptured with sawtooth failure surfaces shown as brittle failure; for compression failure, the two modes of compression are buckling and compression shear failure. The stress–strain relationship curves of the bamboo scrimber and laminated bamboo are also similar. The tensile stress–strain curves showed a linear relationship, and the compressive stress–strain curves can be divided into three stages: elastic, elastoplastic and post-yield. Based on the test results, the stress–strain model was proposed for glulam bamboo, in which a linear equation was used to describe the tensile stress–strain relationship and the Richard–Abbott model was employed to model the compressive stress–strain relationship. A comparison with the experimental results shows that the predicted results are in good agreement with the experimental curves.

Compressive stress-strain model for low-calcium fly ash-based geopolymer and heat-cured Portland cement concrete

2016 ◽  
Vol 73 ◽  
pp. 136-146 ◽  
Author(s):  
Amin Noushini ◽  
Farhad Aslani ◽  
Arnaud Castel ◽  
Raymond Ian Gilbert ◽  
Brian Uy ◽  
...  
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Compressive Stress ◽  
Portland Cement Concrete ◽  
Cement Concrete ◽  
Stress Strain ◽  
Low Calcium ◽  
Strain Model

Compressive strengths of concrete-filled double-skin (circular hollow section outer and square hollow section inner) aluminium tubular sections

2019 ◽  
Vol 22 (11) ◽  
pp. 2418-2434 ◽  
Author(s):  
Feng Zhou ◽  
Ben Young
Keyword(s):  
Concrete Strength ◽  
Element Model ◽  
Numerical Results ◽  
Outer Skin ◽  
Hollow Section ◽  
Composite Columns ◽  
Double Skin ◽  
Stub Column ◽  
Circular Hollow Section ◽  
Stub Columns

Experimental and numerical investigations of concrete-filled double-skin aluminium stub column with a circular hollow section as the outer skin and a square hollow section as the inner skin are presented in this article. A test program was carried out to study the influences of aluminium tube geometric dimensions and concrete strength on structural performance and strength of composite columns. A series of composite columns was tested on outer circular hollow section tubes and inner square hollow section tubes; the spaces between them had been filled with concrete of different nominal cylinder strengths of 40, 70 and 100 MPa. The tubes were fabricated by extrusion using 6061T6 heat-treated aluminium alloy having a nominal 0.2% proof stress of 240 MPa. A non-linear finite element model was developed and verified against experimental results. The test and numerical results were compared with the design strengths to evaluate the applicability of the design rules in the American specifications for aluminium and concrete structures. In addition, the proposed design equations, developed by the authors for concrete-filled double-skin aluminium tubular stub columns with circular hollow section as both outer and inner skins, were used to calculate the design strengths and compared with the experimental and numerical results obtained in this study. The proposed design equations also predicted the ultimate strengths of the concrete-filled double-skin aluminium tubular stub columns accurately with circular hollow section as the outer skin and square hollow section as the inner skin.

scholarly journals Local buckling of thin-walled circular hollow section under uniform bending

2021 ◽  
Vol 15 (4) ◽  
pp. 88-98
Author(s):  
Bui Hung Cuong
Keyword(s):  
Critical Stress ◽  
Local Buckling ◽  
Critical Length ◽  
Hollow Section ◽  
Finite Strip ◽  
Finite Strip Method ◽  
Half Wave ◽  
Parametric Studies ◽  
Thin Walled ◽  
Circular Hollow Section

This article presents a semi-analytical finite strip method based on Marguerre’s shallow shell theory and Kirchhoff’s assumption. The formulated finite strip is used to study the buckling behavior of thin-walled circular hollow sections (CHS) subjected to uniform bending. The shallow finite strip program of the present study is compared to the plate strip implemented in CUFSM4.05 program for demonstrating the accuracy and better convergence of the former. By varying the length of the CHS, the signature curve relating buckling stresses to half-wave lengths is established. The minimum local buckling point with critical stress and corresponding critical length can be found from the curve. Parametric studies are performed to propose approximative expressions for calculating the local critical stress and local critical length of steel and aluminum CHS.

Sign in / Sign up

Export Citation Format

Share Document