Experimental investigation of turbulent shear flow with quadratic mean-velocity profiles

1976 ◽  
Vol 73 (1) ◽  
pp. 165-188 ◽  
Author(s):  
H. K. Richards ◽  
J. B. Morton
Keyword(s):  
Flow Direction ◽  
Correlation Coefficients ◽  
Velocity Profiles ◽  
Turbulent Shear ◽  
Turbulent Shear Flow ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Mean Velocity ◽  
Quadratic Mean ◽  
The Mean

Three turbulent shear flows with quadratic mean-velocity profiles are generated by using an appropriately designed honeycomb and parallel-rod grids with adjustable rod spacing. The details of two of the flow fields, with quadratic mean-velocity profiles with constant positive mean-shear gradients ($\partial^2\overline{U}_1/\partial X^2_2 >0$), are obtained, and include, in the mean flow direction, the development and distribution of mean velocities, fluctuating velocities, Reynolds stresses, microscales, integral scales, energy spectra, shear correlation coefficients and two-point spatial velocity correlation coefficients. A third flow field is generated with a quadratic mean velocity profile with constant negative mean-shear gradient ($\partial^2\overline{U}_1/\partial X^2_2 < 0$), to investigate in the mean flow direction the effect of the change in sign on the resulting field. An open-return wind tunnel with a 2 × 2 × 20 ft test-section is used.

scholarly journals Evolution and structure of sink-flow turbulent boundary layers

2001 ◽  
Vol 428 ◽  
pp. 1-27 ◽  
Author(s):  
M. B. JONES ◽  
IVAN MARUSIC ◽  
A. E. PERRY
Keyword(s):  
Boundary Layers ◽  
Velocity Profiles ◽  
Turbulent Boundary Layers ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Mean Velocity ◽  
Flow Measurements ◽  
Law Of The Wall ◽  
The Mean ◽  
Logarithmic Law

An experimental and theoretical investigation of turbulent boundary layers developing in a sink-flow pressure gradient was undertaken. Three flow cases were studied, corresponding to different acceleration strengths. Mean-flow measurements were taken for all three cases, while Reynolds stresses and spectra measurements were made for two of the flow cases. In this study attention was focused on the evolution of the layers to an equilibrium turbulent state. All the layers were found to attain a state very close to precise equilibrium. This gave equilibrium sink flow data at higher Reynolds numbers than in previous experiments. The mean velocity profiles were found to collapse onto the conventional logarithmic law of the wall. However, for profiles measured with the Pitot tube, a slight ‘kick-up’ from the logarithmic law was observed near the buffer region, whereas the mean velocity profiles measured with a normal hot wire did not exhibit this deviation from the logarithmic law. As the layers approached equilibrium, the mean velocity profiles were found to approach the pure wall profile and for the highest level of acceleration Π was very close to zero, where Π is the Coles wake factor. This supports the proposition of Coles (1957), that the equilibrium sink flow corresponds to pure wall flow. Particular interest was also given to the evolutionary stages of the boundary layers, in order to test and further develop the closure hypothesis of Perry, Marusic & Li (1994). Improved quantitative agreement with the experimental results was found after slight modification of their original closure equation.

Measurement of the Reynolds stresses and the mean-flow field in a three-dimensional pressure-driven boundary layer

1982 ◽  
Vol 119 ◽  
pp. 121-153 ◽  
Author(s):  
Udo R. Müller
Keyword(s):  
Boundary Layer ◽  
Shear Stress ◽  
Flow Field ◽  
Three Dimensional ◽  
Turbulent Shear ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Mean Velocity ◽  
Flow Acceleration ◽  
The Mean

An experimental study of a steady, incompressible, three-dimensional turbulent boundary layer approaching separation is reported. The flow field external to the boundary layer was deflected laterally by turning vanes so that streamwise flow deceleration occurred simultaneous with cross-flow acceleration. At 21 stations profiles of the mean-velocity components and of the six Reynolds stresses were measured with single- and X-hot-wire probes, which were rotatable around their longitudinal axes. The calibration of the hot wires with respect to magnitude and direction of the velocity vector as well as the method of evaluating the Reynolds stresses from the measured data are described in a separate paper (Müller 1982, hereinafter referred to as II). At each measuring station the wall shear stress was inferred from a Preston-tube measurement as well as from a Clauser chart. With the measured profiles of the mean velocities and of the Reynolds stresses several assumptions used for turbulence modelling were checked for their validity in this flow. For example, eddy viscosities for both tangential directions and the corresponding mixing lengths as well as the ratio of resultant turbulent shear stress to turbulent kinetic energy were derived from the data.

Outline of a theory of turbulent shear flow

1956 ◽  
Vol 1 (5) ◽  
pp. 521-539 ◽  
Author(s):  
W. V. R. Malkus
Keyword(s):  
Shear Flow ◽  
Velocity Profile ◽  
Boundary Conditions ◽  
Momentum Transport ◽  
Turbulent Shear ◽  
Spectral Structure ◽  
Turbulent Shear Flow ◽  
Mean Flow ◽  
Mean Velocity ◽  
The Mean

In this paper the spatial variations and spectral structure of steady-state turbulent shear flow in channels are investigated without the introduction of empirical parameters. This is made possible by the assumption that the non-linear momentum transport has only stabilizing effects on the mean field of flow. Two constraints on the possible momentum transport are drawn from this assumption: first, that the mean flow will be statistically stable if an Orr-Sommerfeld type equation is satisfied by fluctuations of the mean; second, that the smallest scale of motion that can be present in the spectrum of the momentum transport is the scale of the marginally stable fluctuations of the mean. Within these two constraints, and for a given mass transport, an upper limit is sought for the rate of dissipation of potential energy into heat. Solutions of the stability equation depend upon the shape of the mean velocity profile. In turn, the mean velocity profile depends upon the spatial spectrum of the momentum transport. A variational technique is used to determine that momentum transport spectrum which is both marginally stable and produces a maximum dissipation rate. The resulting spectrum determines the velocity profile and its dependence on the boundary conditions. Past experimental work has disclosed laminar, ‘transitional’, logarithmic and parabolic regions of the velocity profile. Several experimental laws and their accompanying constants relate the extent of these regions to the boundary conditions. The theoretical profile contains each feature and law that is observed. First approximations to the constants are found, and give, in particular, a value for the logarithmic slope (von Kármán's constant) which is within the experimental error. However, the theoretical boundary constant is smaller than the observed value. Turbulent channel flow seems to achieve the extreme state found here, but a more decisive quantitative comparison of theory and experiment requires improvement in the solutions of the classical laminar stability problem.

The maintenance of Reynolds stress in turbulent shear flow

1967 ◽  
Vol 27 (1) ◽  
pp. 131-144 ◽  
Author(s):  
O. M. Phillips
Keyword(s):  
Shear Flow ◽  
Velocity Profile ◽  
Reynolds Stress ◽  
Mixing Layer ◽  
Turbulent Shear ◽  
Turbulent Shear Flow ◽  
Mean Flow ◽  
Mean Velocity ◽  
Velocity Fluctuations ◽  
The Mean

A mechanism is proposed for the manner in which the turbulent components support Reynolds stress in turbulent shear flow. This involves a generalization of Miles's mechanism in which each of the turbulent components interacts with the mean flow to produce an increment of Reynolds stress at the ‘matched layer’ of that particular component. The summation over all the turbulent components leads to an expression for the gradient of the Reynolds stress τ(z) in the turbulence\[ \frac{d\tau}{dz} = {\cal A}\Theta\overline{w^2}\frac{d^2U}{dz^2}, \]where${\cal A}$is a number, Θ the convected integral time scale of thew-velocity fluctuations andU(z) the mean velocity profile. This is consistent with a number of experimental results, and measurements on the mixing layer of a jet indicate thatA= 0·24 in this case. In other flows, it would be expected to be of the same order, though its precise value may vary somewhat from one to another.

Measurements with a pulsed-wire and a hot-wire anemometer in the highly turbulent wake of a normal flat plate

1976 ◽  
Vol 77 (3) ◽  
pp. 473-497 ◽  
Author(s):  
L. J. S. Bradbury
Keyword(s):  
Turbulent Flow ◽  
Flat Plate ◽  
Flow Direction ◽  
Operating Conditions ◽  
Turbulent Intensity ◽  
Hot Wire ◽  
Mean Flow ◽  
Mean Velocity ◽  
The Mean ◽  
Better Than

This paper describes an investigation into the response of both the pulsed-wire anemometer and the hot-wire anemometer in a highly turbulent flow. The first part of the paper is concerned with a theoretical study of some aspects of the response of these instruments in a highly turbulent flow. It is shown that, under normal operating conditions, the pulsed-wire anemometer should give mean velocity and longitudinal turbulent intensity estimates to an accuracy of better than 10% without any restriction on turbulence level. However, to attain this accuracy in measurements of turbulent intensities normal to the mean flow direction, there is a lower limit on the turbulent intensity of about 50%. An analysis is then carried out of the behaviour of the hot-wire anemometer in a highly turbulent flow. It is found that the large errors that are known to develop are very sensitive to the precise structure of the turbulence, so that even qualitative use of hot-wire data in such flows is not feasible. Some brief comments on the possibility of improving the accuracy of the hot-wire anemometer are then given.The second half of the paper describes some comparative measurements in the highly turbulent flow immediately downstream of a normal flat plate. It is shown that, although it is not possible to interpret the hot-wire results on their own, it is possible to calculate the hot-wire response with a surprising degree of accuracy using the results from the pulsed-wire anemometer. This provides a rather indirect but none the less welcome check on the accuracy of the pulsed-wire results, which, in this very highly turbulent flow, have a certain interest in their own right.

Anisotropic pressure correlation spectra in turbulent shear flow

2012 ◽  
Vol 694 ◽  
pp. 50-77 ◽  
Author(s):  
Yoshiyuki Tsuji ◽  
Yukio Kaneda
Keyword(s):  
Mixing Layer ◽  
Inertial Subrange ◽  
Turbulent Shear ◽  
Pressure Probe ◽  
Anisotropic Pressure ◽  
Turbulent Shear Flow ◽  
Velocity Correlation ◽  
Mean Velocity ◽  
Correlation Spectrum ◽  
The Mean

AbstractWe measured the correlation spectrum ${\hat {Q} }_{p} (\mathbi{k})$ of pressure fluctuations in a driving mixing layer with a Taylor-scale Reynolds number ${R}_{\lambda } $ up to ${\simeq }700$ by a newly developed pressure probe with spatial and temporal resolutions that are sufficient to analyse inertial-subrange statistics. The influence of the mean velocity gradient tensor ${S}_{ij} $ in the mixing layer, which is almost constant near its centreline, is studied using an idea similar to that underlying the linear response theory developed in statistical mechanics for systems at or near thermal equilibrium. If we write the spectrum ${\hat {Q} }_{p} (\mathbi{k})$ as ${\hat {Q} }_{p} (\mathbi{k})= { \hat {Q} }_{p}^{(0)} (\mathbi{k})+ \mrm{\Delta} {\hat {Q} }_{p} (\mathbi{k})$, where ${ \hat {Q} }_{p}^{(0)} (\mathbi{k})$ is the isotropic Kolmogorov spectrum in the absence of mean shear, then for small ${S}_{ij} $ the deviation $ \mrm{\Delta} {\hat {Q} }_{p} (\mathbi{k})$ due to the shear is approximately linear and is determined by a few non-dimensional universal constants in addition to ${S}_{ij} $, $k$ and the mean energy dissipation rate. We also measured the pressure–velocity and velocity–velocity correlation spectra. Deviations from isotropy due to shear are shown to be approximately proportional to ${S}_{ij} $ at large ${R}_{\lambda } $.

Sinusoidal Excitation of a Free Turbulent Jet With Constant Amplitude Transverse Pressure Gradients Near the Nozzle Exit: Part I: Measurement of Mean Shear Velocities

1973 ◽  
Vol 95 (2) ◽  
pp. 167-173
Author(s):  
A. K. Stiffler ◽  
J. L. Shearer
Keyword(s):  
Nozzle Exit ◽  
Flow Direction ◽  
Excitation Frequency ◽  
Velocity Profiles ◽  
Turbulent Jet ◽  
Pressure Gradients ◽  
Mean Velocity ◽  
Effective Velocity ◽  
Gaussian Distribution Function ◽  
The Mean

A free turbulent jet is perturbed transverse to the flow direction by a sinusoidal pressure gradient near the nozzle exit. Velocities in the jet are determined by hot wire anemometer measurements. Moving effective mean velocity profiles are defined and reconstructed from the point-by-point stationary measurements of the mean velocity and of the harmonic content of the time varying signal. The effective velocity profiles are described by the Gaussian distribution function where the spread parameter decays as the cube of the product of the excitation frequency and the downstream location from the nozzle. These profile measurements and analysis of their characteristics lead to a better understanding of the factors determining the gain of a fluidic amplifier under conditions of high frequency operation.

scholarly journals Experimental Study of Mean Flow Characteristics in the Near Field of Wedge-Shaped Swirling Jets

2020 ◽  
Vol 5 (10) ◽  
pp. 1199-1203
Author(s):  
Md. Mosharrof Hossain ◽  
Muhammed Hasnain Kabir Nayeem ◽  
Dr. Md Abu Taher Ali
Keyword(s):  
Flow Field ◽  
Near Field ◽  
Flow Characteristics ◽  
Velocity Profiles ◽  
Mean Flow ◽  
Mean Velocity ◽  
Potential Core ◽  
Swirling Jets ◽  
The Mean ◽  
Sinusoidal Flow

In this investigation experiment was carried out in 80 mm diameter swirling pipe jet, where swirl was generated by attaching wedge-shaped helixes in the pipe. All measurements were taken at Re 5.3e4. In the plain pipe jet the potential core was found to exist up to x/D=5 but in the swirling jet there was no existence of potential core. The mean velocity profiles were found to be influenced by the presence of wedge-shaped helixes in the pipe. The velocity profiles indicated the presence of sinusoidal flow field in the radial direction existed only in the near field of the jet. This flow field died out after x/D=3 and the existence of jet flow diminished after x/D=5.

Scaling of Favorable Pressure Gradient Turbulent Boundary Layers With Eventual Relaminarization

2005 ◽  
Author(s):  
Rau´l Bayoa´n Cal ◽  
Xia Wang ◽  
Luciano Castillo
Keyword(s):  
Boundary Layer ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Reynolds Shear Stress ◽  
Velocity Profiles ◽  
Turbulent Boundary Layers ◽  
Reynolds Stresses ◽  
Mean Velocity ◽  
Favorable Pressure Gradient ◽  
The Mean

Applying similarity analysis to the RANS equations of motion for a pressure gradient turbulent boundary layer, Castillo and George [1] obtained the scalings for the mean deficit velocity and the Reynolds stresses. Following this analysis, Castillo and George studied favorable pressure gradient (FPG) turbulent boundary layers. They were able to obtain a single curve for FPG flows when scaling the mean deficit velocity profiles. In this study, FPG turbulent boundary layers are analyzed as well as relaminarized boundary layers subjected to an even stronger FPG. It is found that the mean deficit velocity profiles diminish when scaled using the Castillo and George [1] scaling, U∞, and the Zagarola and Smits [2] scaling, U∞δ*/δ. In addition, Reynolds stress data has been analyzed and it is found that the relaminarized boundary layer data decreases drastically in all components of the Reynolds stresses. Furthermore, it will be shown that the shape of the profile for the wall-normal and Reynolds shear stress components change drastically given the relaminarized state. Therefore, the mean velocity deficit profiles as well as Reynolds stresses are found to be necessary in order to understand not only FPG flows, but also relaminarized boundary layers.

Sign in / Sign up

Export Citation Format

Share Document