scholarly journals A new environmentally-friendly route to in situ form a high-corrosion-resistant nesquehonite film on pure magnesium

RSC Advances ◽  
2020 ◽  
Vol 10 (58) ◽  
pp. 35480-35489 ◽  
Author(s):  
Xianlong Cao ◽  
Quanyou Ren ◽  
Youkun Yang ◽  
Xianglong Hou ◽  
Yongbo Yan ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Environmentally Friendly ◽  
Pure Magnesium ◽  
Protective Film ◽  
High Corrosion Resistance ◽  
Corrosion Resistant ◽  
High Corrosion

A nesquehonite protective film with high corrosion resistance was prepared on pure Mg via a new environmentally-friendly in situ carbonation route.

scholarly journals Alkali activated cements mix design for concretes application in high corrosive conditions

2018 ◽  
Vol 230 ◽  
pp. 03007 ◽  
Author(s):  
Oleksandr Kovalchuk ◽  
Valentina Grabovchak ◽  
Yaroslav Govdun
Keyword(s):  
Corrosion Resistance ◽  
Phase Composition ◽  
Mix Design ◽  
Cement Stone ◽  
Hydration Products ◽  
Alkali Content ◽  
High Corrosion Resistance ◽  
Corrosion Resistant ◽  
High Corrosion ◽  
Alkali Activated

This paper covers the results of development of corrosion resistant ash alkali-activated cements based on regulation of phase composition of the hydration products through changing the alkali content, content of calciumcontaining cement constituents resulting in the increase strength and density of the cement stone. The results of study suggested to conclude that the cement compositions with predominance in the hydration products of weakly soluble low basic hydrosilicates of calcium, hydrogarnets and minerals similar to natural hydroaluminates exhibited the highest corrosion resistance. The results of comparison suggested to draw a conclusion that the alkali-activated cements Types APC III-400 and ACC V-400, according to National Ukrainian Standard DSTU B V.2.7, had high corrosion resistance compared to that of OPC, thus allowing to recommend the developed cements for the concretes intended for use in aggressive environments, inclusive of sodium and magnesium sulphates and others. Coefficients of corrosion resistance of concretes are higher than 1 after even 42 months.

scholarly journals Environmentally Friendly Composite Film of Anodizing and Electrodeposition Coating Having a High Corrosion Resistance on Magnesium Alloy AZ91D

2007 ◽  
Vol 48 (12) ◽  
pp. 3118-3125 ◽  
Author(s):  
Masaaki Hara ◽  
Kenji Matsuda ◽  
Wataru Yamauchi ◽  
Masaaki Sakaguchi ◽  
Toshiyuki Yoshikata ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Magnesium Alloy ◽  
Composite Film ◽  
Environmentally Friendly ◽  
High Corrosion Resistance ◽  
High Corrosion ◽  
Alloy Az91d

scholarly journals Angle resolver X-ray photoelectron spectroscopic analysis of the passive film of the corrosion-resistant W-32Zr alloy in 12 M HCl solution

2015 ◽  
Vol 49 (2) ◽  
pp. 103-110
Author(s):  
Jagadeesh Bhattarai
Keyword(s):  
Corrosion Resistance ◽  
Synergistic Effects ◽  
High Corrosion Resistance ◽  
Corrosion Resistant ◽  
X Ray ◽  
High Corrosion ◽  
Average Corrosion Rate ◽  
Sputter Deposited ◽  
Zirconium Metal ◽  
Hcl Solution

The sputter-deposited amorphous W-32Zr alloy was passivated spontaneously and showed a fairly high corrosion resistance in 12 M HCl solution in open air at 30°C. The average corrosion rate of the W-32Zr alloy (i.e., 5.2 × 10-3 mm/y) was found to be lower than those of alloy-constituting tungsten and zirconium elements. Such synergistic effects of simultaneous addition of tungsten and zirconium in the W–32Zr alloy was investigated by corrosion tests, electrochemical measurements and angle resolved X-ray photoelectron spectroscopic (ARXPS) analyses. High corrosion resistance of the binary W–32Zr alloy is mostly due to the formation of homogeneous passive oxyhydroxide film consisting of Wox and Zr4+ cations with a small concentration gradient in–depth from ARXPS analysis. Consequently, zirconium metal acts synergistically with tungsten in enhancing the anodic passivity as well as the corrosion resistance properties of the sputter–deposited W–32Zr alloy in 12 M HCl solution open to air at 30°C. DOI: http://dx.doi.org/10.3329/bjsir.v49i2.22004 Bangladesh J. Sci. Ind. Res. 49(2), 103-110, 2014

BRIMCOLLOY

Alloy Digest ◽  
1971 ◽  
Vol 20 (1) ◽  
Keyword(s):  
Corrosion Resistance ◽  
Physical Properties ◽  
Surface Treatment ◽  
Tensile Properties ◽  
High Strength ◽  
Heat Treating ◽  
High Corrosion Resistance ◽  
Rolling Mills ◽  
High Corrosion ◽  
Copper Zinc

Abstract BRIMCOLLOY is a copper-zinc tin alloy having high strength, spring temper, superior conductivity and high corrosion resistance. It is produced in three grades: BRIMCOLLOY 100, BRIMCOLLOY 200, and BRIMCOLLOY 300. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: Cu-225. Producer or source: Bridgeport Rolling Mills Company.

HASTELLOY ALLOY F

Alloy Digest ◽  
1956 ◽  
Vol 5 (12) ◽  
Keyword(s):  
Fracture Toughness ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Cold Working ◽  
Iron Alloy ◽  
Heat Treating ◽  
High Corrosion Resistance ◽  
High Corrosion ◽  
Nickel Chromium

Abstract HASTELLOY ALLOY-F is a nickel-chromium-molybdenum-iron alloy having high corrosion resistance and possessing satisfactory hot and cold working characteristics. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness and creep. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: Ni-30. Producer or source: Haynes Stellite Company.

UGI 209

Alloy Digest ◽  
2014 ◽  
Vol 63 (11) ◽  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Austenitic Stainless Steel ◽  
Physical Properties ◽  
Surface Treatment ◽  
Tensile Properties ◽  
Magnetic Permeability ◽  
Heat Treating ◽  
High Corrosion Resistance ◽  
High Corrosion

Abstract UGI 209 is an austenitic stainless steel with high corrosion resistance and a low magnetic permeability. This datasheet provides information on composition, physical properties, microstructure, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: SS-1192. Producer or source: Schmolz + Bickenbach USA Inc..

Anodic synthesis of TiO2 nanotubes by step-up voltages

2021 ◽  
pp. 002199832110237
Author(s):  
V Sivaprakash ◽  
R Narayanan
Keyword(s):  
Corrosion Resistance ◽  
Tio2 Nanotubes ◽  
Biomedical Applications ◽  
Phase Changes ◽  
Electrochemical Anodization ◽  
Corrosion Resistant ◽  
Anodization Process ◽  
Anodic Synthesis ◽  
Input Potential

Fabrication of TiO2 nanotubes (NTs) has extensive application properties due to their high corrosion resistant and compatibility with biomedical applications, the synthesis of TiO2 nanotubes over titanium has drawn interest in various fields. The synthesis of TiO2 NTs using novel in-situ step-up voltage conditions in the electrochemical anodization process is recorded in this work. For manufacturing the NTs at 1 hour of anodization, the input potential of 30, 40 and 50 V was selected. With increasing step-up voltage during the anodization process, an improvement in the NTs was observed, favoring corrosion resistance properties. The surface of NTs enhances the structure of the ribs, raising the potential for feedback over time. XRD was used to analyze phase changes, and HR-SEM analyzed surface topography. Impedance tests found that longer NTs improved the corrosion resistance.

Sign in / Sign up

Export Citation Format

Share Document