scholarly journals Alkali activated cements mix design for concretes application in high corrosive conditions

2018 ◽  
Vol 230 ◽  
pp. 03007 ◽  
Author(s):  
Oleksandr Kovalchuk ◽  
Valentina Grabovchak ◽  
Yaroslav Govdun

This paper covers the results of development of corrosion resistant ash alkali-activated cements based on regulation of phase composition of the hydration products through changing the alkali content, content of calciumcontaining cement constituents resulting in the increase strength and density of the cement stone. The results of study suggested to conclude that the cement compositions with predominance in the hydration products of weakly soluble low basic hydrosilicates of calcium, hydrogarnets and minerals similar to natural hydroaluminates exhibited the highest corrosion resistance. The results of comparison suggested to draw a conclusion that the alkali-activated cements Types APC III-400 and ACC V-400, according to National Ukrainian Standard DSTU B V.2.7, had high corrosion resistance compared to that of OPC, thus allowing to recommend the developed cements for the concretes intended for use in aggressive environments, inclusive of sodium and magnesium sulphates and others. Coefficients of corrosion resistance of concretes are higher than 1 after even 42 months.

RSC Advances ◽  
2020 ◽  
Vol 10 (58) ◽  
pp. 35480-35489 ◽  
Author(s):  
Xianlong Cao ◽  
Quanyou Ren ◽  
Youkun Yang ◽  
Xianglong Hou ◽  
Yongbo Yan ◽  
...  

A nesquehonite protective film with high corrosion resistance was prepared on pure Mg via a new environmentally-friendly in situ carbonation route.


2015 ◽  
Vol 49 (2) ◽  
pp. 103-110
Author(s):  
Jagadeesh Bhattarai

The sputter-deposited amorphous W-32Zr alloy was passivated spontaneously and showed a fairly high corrosion resistance in 12 M HCl solution in open air at 30°C. The average corrosion rate of the W-32Zr alloy (i.e., 5.2 × 10-3 mm/y) was found to be lower than those of alloy-constituting tungsten and zirconium elements. Such synergistic effects of simultaneous addition of tungsten and zirconium in the W–32Zr alloy was investigated by corrosion tests, electrochemical measurements and angle resolved X-ray photoelectron spectroscopic (ARXPS) analyses. High corrosion resistance of the binary W–32Zr alloy is mostly due to the formation of homogeneous passive oxyhydroxide film consisting of Wox and Zr4+ cations with a small concentration gradient in–depth from ARXPS analysis. Consequently, zirconium metal acts synergistically with tungsten in enhancing the anodic passivity as well as the corrosion resistance properties of the sputter–deposited W–32Zr alloy in 12 M HCl solution open to air at 30°C. DOI: http://dx.doi.org/10.3329/bjsir.v49i2.22004 Bangladesh J. Sci. Ind. Res. 49(2), 103-110, 2014


Alloy Digest ◽  
1971 ◽  
Vol 20 (1) ◽  

Abstract BRIMCOLLOY is a copper-zinc tin alloy having high strength, spring temper, superior conductivity and high corrosion resistance. It is produced in three grades: BRIMCOLLOY 100, BRIMCOLLOY 200, and BRIMCOLLOY 300. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: Cu-225. Producer or source: Bridgeport Rolling Mills Company.


Alloy Digest ◽  
1956 ◽  
Vol 5 (12) ◽  

Abstract HASTELLOY ALLOY-F is a nickel-chromium-molybdenum-iron alloy having high corrosion resistance and possessing satisfactory hot and cold working characteristics. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness and creep. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: Ni-30. Producer or source: Haynes Stellite Company.


Alloy Digest ◽  
2014 ◽  
Vol 63 (11) ◽  

Abstract UGI 209 is an austenitic stainless steel with high corrosion resistance and a low magnetic permeability. This datasheet provides information on composition, physical properties, microstructure, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: SS-1192. Producer or source: Schmolz + Bickenbach USA Inc..


Sign in / Sign up

Export Citation Format

Share Document