scholarly journals Optimization of Shell and Tube Condenser for Low Temperature Thermal Desalination Plant

2021 ◽  
Vol 309 ◽  
pp. 01011
Author(s):  
R Elakkiyadasan ◽  
Kumar P Manoj ◽  
M Subramanian ◽  
N Balaji ◽  
M Karthick ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Transfer Coefficient ◽  
Mass Flow Rate ◽  
Flow Rate ◽  
Heat Exchangers ◽  
Pumping Power ◽  
Overall Heat Transfer Coefficient ◽  
Shell And Tube

In the current work, attempt for enhancing the heat exchanger of the shell and tube by analyzing the various parameters. The heat exchanger is a device used to transfer heat between at least two fluids. In the different kinds of heat exchangers utilized in various industries, shell and tube heat exchangers are presumably the most adaptable and widely heat exchangers utilized in most industrial areas. Based on the relationship between different parameters such as tube velocity, overall heat transfer coefficient, mass flow rate, and pumping power, analysis is carried out. Results show that the tube velocity increases the overall heat transfer coefficient, total pressure drop and mass flow rate of water, Pumping Power, up to the certain limit and starts to decrease. So that the parameters can be optimized by conducting the experiments based on different input parameters. The parameters which influence the optimal result are researched and recommended.

scholarly journals Experimental Investigation Of Heat Transfer Characteristics Of Nanofluid Using Parallel Flow, Counter Flow And Shell And Tube Heat Exchanger

2015 ◽  
Vol 62 (4) ◽  
pp. 509-522 ◽  
Author(s):  
R. Dharmalingam ◽  
K.K. Sivagnanaprabhu ◽  
J. Yogaraja ◽  
S. Gunasekaran ◽  
R. Mohan
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Transfer Coefficient ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Tube Heat Exchanger ◽  
Overall Heat Transfer Coefficient ◽  
Shell And Tube

Abstract Cooling is indispensable for maintaining the desired performance and reliability over a very huge variety of products like electronic devices, computer, automobiles, high power laser system etc. Apart from the heat load amplification and heat fluxes caused by many industrial products, cooling is one of the major technical challenges encountered by the industries like manufacturing sectors, transportation, microelectronics, etc. Normally water, ethylene glycol and oil are being used as the fluid to carry away the heat in these devices. The development of nanofluid generally shows a better heat transfer characteristics than the water. This research work summarizes the experimental study of the forced convective heat transfer and flow characteristics of a nanofluid consisting of water and 1% Al2O3 (volume concentration) nanoparticle flowing in a parallel flow, counter flow and shell and tube heat exchanger under laminar flow conditions. The Al2O3 nanoparticles of about 50 nm diameter are used in this work. Three different mass flow rates have been selected and the experiments have been conducted and their results are reported. This result portrays that the overall heat transfer coefficient and dimensionless Nusselt number of nanofluid is slightly higher than that of the base liquid at same mass flow rate at same inlet temperature. From the experimental result it is clear that the overall heat transfer coefficient of the nanofluid increases with an increase in the mass flow rate. It shows that whenever mass flow rate increases, the overall heat transfer coefficient along with Nusselt number eventually increases irrespective of flow direction. It was also found that during the increase in mass flow rate LMTD value ultimately decreases irrespective of flow direction. However, shell and tube heat exchanger provides better heat transfer characteristics than parallel and counter flow heat exchanger due to multi pass flow of nanofluid. The overall heat transfer coefficient, Nusselt number and logarithmic mean temperature difference of the water and Al2O3 /water nanofluid are also studied and the results are plotted graphically.

Heat Transfer Enhancement Analysis of Al2O3-Water Nanofluid Through Parallel and Counter Flow in Shell and Tube Heat Exchangers

2017 ◽  
Vol 16 (05n06) ◽  
pp. 1750020 ◽  
Author(s):  
S. Nallusamy ◽  
N. Manikanda Prabu
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Transfer Coefficient ◽  
Mass Flow ◽  
Flow Rate ◽  
Heat Exchangers ◽  
Counter Flow ◽  
Overall Heat Transfer Coefficient ◽  
Shell And Tube

Heat exchanger plays an essential part in industrial sector in transferring the heat energy. Heat is exchanged between fluids in convection and conduction mode through the walls of the heat exchanger. If the heat transfer medium has low thermal conductivity, it will greatly limit the efficiency of the heat exchanger. Whenever the system acts subjected to an increase in the heat load, heat fluxes caused by more power and smaller size, cooling is one of the technical challenges faced by the industries. The objective of this research work is to evaluate the overall heat transfer coefficient through an experimental analysis on the convective heat transfer and flow characteristics of a nanofluid. In our experiment, the nanofluid consists of water and one percentage volume concentration of Al2O3-water nanofluid flowing through parallel and counter flow in shell and tube heat exchangers. About 50[Formula: see text]nm diameter of Al2O3 nanoparticles was used in this analysis and found that the overall heat transfer coefficient and convective heat transfer coefficient of nanofluid were slightly higher than those of the base liquid at same mass flow rate and inlet temperature. Here, there are three samples of dissimilar mass flow rates, which have been identified for conducting the experiments and their results are continuously monitored and reported. Finally, the observed results through an experimental investigation were presented and concluded that the enhancement of overall heat transfer coefficient is likely to be feasible by means of increasing the mass flow rate of base fluid and prepared nanofluid on the proportional basis.

scholarly journals Effect of nanoparticles on heat transfer in heat exchangers

2015 ◽  
Vol 37 ◽  
pp. 199
Author(s):  
Ali Mahrooghi ◽  
Mohammad Moghiman
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Transfer Coefficient ◽  
Flow Rate ◽  
Heat Exchangers ◽  
Water Pressure ◽  
Two Phase ◽  
Tube Heat Exchanger ◽  
Overall Heat Transfer Coefficient

In this paper, forced convection flow and heat transfer of a Al2O3/Water nanofluid have beeninvestigated numerically by single and two phase (volume of fluid) models. Nanofluid flows inside the innertube of the isothermally concentric circular and sinusoidal double tube heat exchangers while hot pure waterflows in the outer tube. The single-phase and two-phase models is used to simulate the nanofluid forcedconvection of 2% and 3% volume concentrations. The renormalization group k-ε model is used to simulateturbulence in ANSYS FLUENT 15.0. Results show that the overall heat transfer coefficient increases withnanoparticle volume concentrations in the heat exchangers. The highest overall heat transfer coefficient rates aredetected, for each concentration and shape, corresponding to the highest flow rate for the sinusoidal tube heatexchanger . The maximum overall heat transfer coefficient enhancement is 220% for the particle volumeconcentration of 3% at the inner tube of concentric sinusoidal double tube heat exchanger corresponding to flowrate =10 LPM. The results reveal that the Al2O3/water pressure drop along the inner tube of circular andsinusoidal double tube heat exchanger increases by about 3% and 5% for volume concentrations of 2% and 3%,respectively, given flow rate compared to the base fluid.Comparison of these results with Rohit S. Khedkar‘spublished experimental data, showed good agreement.

The Effect of Baffles in Shell and Tube Heat Exchangers

2009 ◽  
Vol 62-64 ◽  
pp. 694-699 ◽  
Author(s):  
E. Akpabio ◽  
I.O. Oboh ◽  
E.O. Aluyor
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Heat Exchangers ◽  
Proper Position ◽  
Process Industries ◽  
Overall Heat Transfer Coefficient ◽  
Shell And Tube ◽  
Optimal Values ◽  
Side Flow

Shell and tube heat exchangers in their various construction modifications are probably the most widespread and commonly used basic heat exchanger configuration in the process industries. There are many modifications of the basic configuration which can be used to solve special problems. Baffles serve two functions: Most importantly, they support the tubes in the proper position during assembly and operation and prevent vibration of the tubes caused by flow-induced eddies, and secondly, they guide the shell-side flow back and forth across the tube field, increasing the velocity and the heat transfer coefficient. The objective of this paper is to find the baffle spacing at fixed baffle cut that will give us the optimal values for the overall heat transfer coefficient. To do this Microsoft Excel 2003 package was employed. The results obtained from previous studies showed that to obtain optimal values for the overall heat transfer coefficient for the shell and tube heat exchangers a baffle cut of 20 to 25 percent of the diameter is common and the maximum spacing depends on how much support the tubes need. This was used to validate the results obtained from this study.

scholarly journals Performance Analysis of Shell and Tube Type Heat Exchanger Using Aluminium Oxide (Al2O3) Nano-Particle

2021 ◽  
Vol 9 (9) ◽  
pp. 157-164
Author(s):  
Paritosh Singh
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Transfer Coefficient ◽  
Solid Particles ◽  
Tube Heat Exchanger ◽  
Overall Heat Transfer Coefficient ◽  
Shell And Tube ◽  
Evacuated Tube

Abstract: Research in convective heat transfer using suspensions of nanometer sized solid particles in a base fluid started only over the past decade. Recent investigations on nanofluids, as such suspensions are often called, indicate that the suspended nanoparticles markedly change the transport properties and heat transfer characteristics of the suspension. The very first part of the research work summarizes about the various thermo physical properties of Al2O3 Nanofluid. In evacuated tube solar water heating system nanofluids are used as primary fluid and DM water as secondary fluid in Shell and Tube Heat Exchanger. The experimental analysis of Shell and Tube heat exchanger integrated with Evacuated tube solar collector have been carried out with two types of primary fluids. Research study of shell and tube heat exchanger is focused on heat transfer enhancement by usage of nano fluids. Conventional heat transfer fluids have inherently low thermal conductivity that greatly limits the heat exchange efficiency. The result of analysis shows that average relative variation in LMTD and overall heat transfer coefficient is 24.56% and 52.0% respectively. The payback period of system is reduced by 0.4 years due to saving is in replacement cost of Evacuated Tube Collector. Keywords: ETC; Nanofluid; LMTD; Thermal Conductivity; Overall heat transfer coefficient

scholarly journals Heat transfer analysis in counter flow shell and tube heat exchanger using of design of experiments

2021 ◽  
pp. 77-77
Author(s):  
Sakthivel Perumal ◽  
Dinesh Sundaresan ◽  
Rajkumar Sivanraju ◽  
Nega Tesfie ◽  
Kamalakannan Ramalingam ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Transfer Coefficient ◽  
Fluid Film ◽  
Heat Transfer Analysis ◽  
Counter Flow ◽  
Tube Heat Exchanger ◽  
Overall Heat Transfer Coefficient ◽  
Shell And Tube

In this research aimed to estimate the Overall heat transfer coefficient of counter flow Shell and Tube heat exchanger. Heat transfer is the phenomenon to analysis of heat transfer from one medium of fluid to another medium of fluid, it is considered as a major role in industrial applications. Numerous heat exchangers are available, in this research considered as shell and tube heat exchanger. Overall Heat Transfer Coefficient (OHTC) informed that three major factors are influenced as passing of fluid (film) media coefficient inside the tubes, circulating of fluid (film) media coefficient over in the shell and the resistance of wall made on metal. In this study Taguchi L9 Orthogonal array is executed to found the overall heat transfer coefficient with effective process parameters. Three major parameters are considered for this work are coil diameter (25 mm, 30 mm and 35 mm), Baffle thickness (15 mm, 20 mm and 25 mm) and Baffle gap (200 mm, 300 mm and 400 mm. Baffle plate thickness is highly significant factor for this experiment.

scholarly journals Effective Overall Heat Transfer Coefficient Solver in a Triple Concentric-Tube Heat Exchanger

2019 ◽  
Vol 70 (6) ◽  
pp. 2040-2043
Author(s):  
Sinziana Radulescu ◽  
Loredana Irena Negoita ◽  
Ion Onutu
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Transfer Coefficient ◽  
Heat Exchangers ◽  
Operating Conditions ◽  
Total Thermal Resistance ◽  
Tube Heat Exchanger ◽  
Overall Heat Transfer Coefficient

A relation for calculation of the effective overall heat transfer coefficient in a triple concentric-tube heat exchanger is proposed. The relation of the effective overall heat transfer coefficient is obtained based on total thermal resistance and it is applied within a case study for thermal analysis of two triple concentric-tube heat exchangers with different geometries, hot fluids and operating conditions. Through case study it is found that the values of effective overall heat transfer coefficient can be obtained with acceptable errors, up to 3 % for both heat exchangers.

scholarly journals Experimentation on Augmenting Heat Transfer Characteristics of (Ethylene Glycol + Water) Mixture in A Combined (Pipe in Pipe and Shell & Tube) Heat Exchanger

2019 ◽  
Vol 8 (3) ◽  
pp. 4442-4449
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Heat Exchangers ◽  
Working Fluid ◽  
Counter Flow ◽  
Tube Heat Exchanger ◽  
Overall Heat Transfer Coefficient

In this research work, the design of pipe in pipe, shelland-tube and combined heat exchanger (previously mentioned types were combined to consider as one unit) has been made. These three heat exchangers have been utilized for two kinds of flows i.e., parallel as well counter flow types individually. The design of combined heat exchanger takes been proposed with the idea of increasing the heat transfer area and to understand the behavior of various parameters involved by comparing with the individual heat exchangers. 75:25 aqueous Ethylene Glycols, have been used as the working fluid in all three heat exchangers of counter as well parallel flow conditions. Total quantity of working fluid is 12 liters, in which 6liters of fluid is used as cold fluid and the other half is used as hot fluid. As a result, overall heat transfer coefficient (U) has been increased with increase of mass flow rate. Highest overall heat transfer coefficient value observed as 1943w/m2 -k at highest mass flow rate (within the considerations of this work) of 0.145 kg/s. The highest decrement in LMTD recorded for 0.0425 to 0.145 increase of mass flow rate is 49.32% in shell-and-tube heat exchanger of parallel flow arrangement. The highest effectiveness is observed for pipe in pipe counter flow heat exchanger case, which is 0.39 at a mass flow rate of 0.145kg/s.

Application of Nanofluids in a Shell-and-Tube Heat Exchanger

2013 ◽  
Author(s):  
Jonathan Cox ◽  
Anoop Kanjirakat ◽  
Reza Sadr
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Heat Exchangers ◽  
Nano Particles ◽  
Experimental Result ◽  
Tube Heat Exchanger ◽  
Shell And Tube

Innovations in the field of nanotechnology have potential to improve industrial productivity and performance. One promising applications of this emerging technology is using nanofluids with enhanced thermal properties. Nanofluids, engineered colloidal suspensions consisting of nano-sized particles (less than 100nm) dispersed in a basefluid, have shown potential as industrial cooling fluids due to the enhanced heat transfer characteristics. Experiments are conducted to compare the overall heat transfer coefficient and pressure drop of water vs. nanofluids in a laboratory scale industrial type shell and tube heat exchanger. Three mass particle concentrations, 2%, 4% and 6%, of SiO2-water nanofluids are formulated by dispersing 20 nm diameter nano particles in desalinated water. Nanofluid and tap water are then circulated in the cold and hot loops, respectively, of the heat exchanger to avoid direct particle deposition on heater surfaces. Interestingly, experimental result show both augmentation and deterioration of heat transfer coefficient for nanofluids depending on the flow rate through the heat exchangers. This trend is consistent with an earlier reported observation for heat transfer in micro channels. This trend may be explained by the counter effect of the changes in thermo-physical properties of fluids together with the fouling on the heat exchanger surfaces. The measured pressure drop in the nanofluids flow shows an increase when compared to that of basefluid that could limit the use of nanofluids in heat exchangers for industrial application.

Sign in / Sign up

Export Citation Format

Share Document