scholarly journals Optical Properties of Canadian Biomass Burning Particles Over Europe Observed with Calipso and Ground-Based Lidar Systems

2020 ◽  
Vol 237 ◽  
pp. 08016
Author(s):  
Christina-Anna Papanikolaou ◽  
Elina Giannakaki ◽  
Alex Papayannis ◽  
Maria Tombrou ◽  
Maria Mylonaki ◽  
...  

A long-lasting biomass burning event affected Europe from 27 August to 3 September 2018. The biomass burning aerosol layers were observed with ground- and space-based lidars in heights ranged between 2-7 km (a.s.l.). The mean backscatter coefficient for the ground-based stations ranged between 0.29 and 1.51 Mm-1sr-1, while the CALIPSO retrieved values ranged between 0.43 and 1.83 Mm-1sr-1. Moreover, the mean Ångström exponent (AEb) values, relevant to backscatter, ranged from 0.83 to 1.04 for the aforementioned lidar stations. At the same time, the mean AEb values obtained from CALIPSO ranged between 0.17 and 1.89. The mean particle depolarization ratio ranged between 0.037 and 0.080.

Sensors ◽  
2020 ◽  
Vol 20 (18) ◽  
pp. 5442
Author(s):  
Christina-Anna Papanikolaou ◽  
Elina Giannakaki ◽  
Alexandros Papayannis ◽  
Maria Mylonaki ◽  
Ourania Soupiona

The aim of this paper is to study the spatio-temporal evolution of a long-lasting Canadian biomass burning event that affected Europe in August 2018. The event produced biomass burning aerosol layers which were observed during their transport from Canada to Europe from the 16 to the 26 August 2018 using active remote sensing data from the space-borne system Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation (CALIPSO). The total number of aerosol layers detected was 745 of which 42% were identified as pure biomass burning. The remaining 58% were attributed to smoke mixed with: polluted dust (34%), clean continental (10%), polluted continental (5%), desert dust (6%) or marine aerosols (3%). In this study, smoke layers, pure and mixed ones, were observed by the CALIPSO satellite from 0.8 and up to 9.6 km height above mean sea level (amsl.). The mean altitude of these layers was found between 2.1 and 5.2 km amsl. The Ångström exponent, relevant to the aerosol backscatter coefficient (532/1064 nm), ranged between 0.9 and 1.5, indicating aerosols of different sizes. The mean linear particle depolarization ratio at 532 nm for pure biomass burning aerosols was found equal to 0.05 ± 0.04, indicating near spherical aerosols. We also observed that, in case of no aerosol mixing, the sphericity of pure smoke aerosols does not change during the air mass transportation (0.05–0.06). On the contrary, when the smoke is mixed with dessert dust the mean linear particle depolarization ratio may reach values up to 0.20 ± 0.04, especially close to the African continent (Region 4).


2019 ◽  
Author(s):  
Lucja Janicka ◽  
Iwona S. Stachlewska

Abstract. The analysis of the aerosol optical properties derived at fine temporal and spatial scales were performed based on measurements obtained during heat wave event in vicinity of a cold weather front in Warsaw on August 9th–11th, 2015. The signals collected by the PollyXT-UW lidar allowed for the calculation of 23 sets of so-called 3β + 2α + 2δ + wv profiles averaged by 30-minutes periods during 2 nights. The total number of 11 different aerosol types and aerosol mixtures were identified with reference to properties within 116 sub-layers in the profiles and were characterized by the mean values. The statistical sample of various optical properties being in agreement for consecutive profiles allowed to assess the spatio-temporal extent of aerosol/mixture types. The mean lidar ratio values of 53–73 sr (355 nm) and 31–45 sr (532 nm) in the layers dominated by the anthropogenic pollution were found. For the layers dominated by the biomass burning aerosol (fresh, moderately fresh, moderately aged) mean lidar ratio was of 69–114 sr (355 nm) and 57–85 sr (532 nm). The colour ratio of lidar ratio (532 / 355) higher than 1, characteristic for aged biomass burning aerosol, was found only in one scattered layer, accompanying with low value of extinction related Ångström exponent of 0.60 ± 0.32 and low particle depolarization ratio. The maximum of the particle depolarization ratio of 4.8–5.0 % at 532 nm were observed in a layer likely contaminated with pollen and in a layer dominated by fresh biomass burning aerosol. This study provides an excellent data set for exploration of separation algorithms, aerosol typing algorithms and microphysical inversion.


2016 ◽  
Author(s):  
M. Ealo ◽  
A. Alastuey ◽  
A. Ripoll ◽  
N. Pérez ◽  
M. C. Minguillón ◽  
...  

Abstract. The study of Saharan dust events (SDE) and biomass burning (BB) emissions are both topic of great scientific interest since they are frequent and important polluting scenarios affecting air quality and climate. The main aim of this work is evaluating the feasibility of using near real-time in situ aerosol optical measurements for the detection of these atmospheric events in the Western Mediterranean Basin (WMB). With this aim, intensive aerosol optical properties (SAE: scattering Ångström exponent, AAE: absorption Ångström exponent, SSAAE: single scattering albedo Ångström exponent, and g: asymmetry parameter) were derived from multi-wavelength aerosol light scattering, hemispheric backscattering and absorption measurements performed at regional (Montseny; MSY, 720 m a.s.l.) and continental (Montsec; MSA, 1570 m a.s.l.) background sites in the WMB. A sensitivity study aiming at calibrating the measured intensive optical properties for SDE and BB detection is presented and discussed. The detection of Saharan dust events (SDE) by means of the SSAAE parameter and Ångström matrix depended on the altitude of the measurement station, and on SDE intensity. At MSA (mountain-top site) SSAAE detected around 85% of SDE compared with 50% at MSY station, where pollution episodes dominated by fine anthropogenic particles frequently masked the effect of mineral dust on optical properties during less intense SDE. Furthermore, an interesting feature of SSAAE was its capability to detect the presence of mineral dust after the end of SDE. Thus, resuspension processes driven by summer regional atmospheric circulations and dry conditions after SDE favored the accumulation of mineral dust at regional level having important consequences for air quality. On average, SAE, AAE and g ranged between -0.7 and 1, 1.3 and 2.5, and 0.5 and 0.75, respectively, during SDE. Based on the Aethalometer model, biomass burning (BB) contribution to equivalent black carbon (BC) accounted for 36% and 40% at MSY and MSA respectively. Linear relationships were found between AAE and %BCbb, with AAE values reaching around 1.5 when %BCbb was higher than 50%. BB contribution to organic matter (OM) at MSY was around 30%. Thus FF combustion sources showed important contributions to both BC and OM in the region under study. Results for OM source apportionment showed good agreement with simultaneous biomass burning organic aerosol (BBOA) and hydrocarbon-like organic aerosol (HOA) calculated from Positive Matrix Factorization (PMF) applied to simultaneous Aerosol Mass Spectrometer (ACSM) measurements. A wildfire episode was identified at MSY, showing AAE values up to 2 when daily BB contributions to BC and OM were 73% and 78% respectively.


2003 ◽  
Vol 108 (D13) ◽  
pp. n/a-n/a ◽  
Author(s):  
Jim M. Haywood ◽  
Simon R. Osborne ◽  
Pete N. Francis ◽  
Andreas Keil ◽  
Paola Formenti ◽  
...  

2016 ◽  
Author(s):  
I. Veselovskii ◽  
P. Goloub ◽  
T. Podvin ◽  
V. Bovchaliuk ◽  
Y. Derimian ◽  
...  

Abstract. West Africa and the adjacent oceanic regions are very important locations for studying dust properties and their influence on weather and climate. The SHADOW (Study of SaHAran Dust Over West Africa) campaign is performing a multi-scale and multi-laboratory study of aerosol properties and dynamics using a set of in situ and remote sensing instruments at an observation site located at IRD (Institute for Research and Development) Center, Mbour, Senegal (14° N, 17° W). In this paper, we present the results of lidar measurements performed during the first phase of SHADOW which occurred in March-April, 2015. The multiwavelength Mie-Raman lidar acquired 3β + 2α + 1δ measurements during this period. This set of measurements has permitted particle intensive properties such as extinction and backscattering Ångström exponents (BAE) for 355/532 nm wavelengths corresponding lidar ratios and depolarization ratio at 532 nm to be determined. The mean values of dust lidar ratios during the observation period were about 53 sr at both 532 nm and 355 nm, which agrees with the values observed during the SAMUM 1 and SAMUM 2 campaigns held in Morocco and Cape Verde in 2006, 2008. The mean value of particle depolarization ratio at 532 nm was 30 ± 4.5 %, however during strong dust episodes this ratio increased to 35 ± 5 %, which is also in agreement with the results of the SAMUM campaigns. The backscattering Ångström exponent during the dust episodes decreased to ~ −0.7, while the extinction Ångström exponent though being negative, was greater than −0.2. Low values of BAE can likely be explained by an increase in the imaginary part of the dust refractive index at 355 nm compared to 532 nm. The dust extinction and backscattering coefficients at multiple wavelengths were inverted to the particle microphysics using the regularization algorithm and the model of randomly oriented spheroids. The analysis performed has demonstrated that the spectral dependence of the imaginary part of the dust refractive index may significantly influence the inversion results and should be taken into account.


2019 ◽  
Author(s):  
Cyrielle Denjean ◽  
Thierry Bourrianne ◽  
Frederic Burnet ◽  
Marc Mallet ◽  
Nicolas Maury ◽  
...  

Abstract. Southern West Africa (SWA) is an African pollution hotspot but a relatively poorly sampled region of the world. We present an overview of in-situ aerosol optical measurements collected over SWA in June and July 2016 as part as the DACCIWA (Dynamics–Aerosol–Chemistry–Clouds Interactions in West Africa) airborne campaign. The aircraft sampled a wide range of air masses, including anthropogenic pollution plumes emitted from the coastal cities, long-range transported biomass burning plumes from Central and Southern Africa and dust plumes from the Sahara and Sahel region, as well as mixtures of these plumes. The specific objective of this work is to characterize the regional variability of the vertical distribution of aerosol particles and their spectral optical properties (single scattering albedo: SSA, asymmetry parameter, extinction mass efficiency, scattering Ångström exponent and absorption Ångström exponent: AAE). First findings indicate that aerosol optical properties in the planetary boundary layer were dominated by a widespread and persistent biomass burning loading from the Southern Hemisphere. Despite a strong increase of aerosol number concentration in air masses downwind of urban conglomerations, spectral SSA were comparable to the background and showed signatures of the absorption characteristics of biomass burning aerosols. In the free troposphere, moderately to strongly absorbing aerosol layers, dominated by either dust or biomass burning particles, occurred occasionally. In aerosol layers dominated by mineral dust particles, SSA varied from 0.81 to 0.92 at 550 nm depending on the variable proportion of anthropogenic pollution particles externally mixed with the dust. Biomass burning aerosol particles were significantly more light absorbing than those previously measured in other areas (e.g. Amazonia, North America) with SSA ranging from 0.71 to 0.77 at 550 nm. The variability of SSA was mainly controlled by variations in aerosol composition rather than in aerosol size distribution. Correspondingly, values of AAE ranged from 0.9 to 1.1, suggesting that lens-coated black carbon particles were the dominant absorber in the visible range for these biomass burning aerosols. Comparison with literature shows a consistent picture of increasing absorption enhancement of biomass burning aerosol from emission to remote location and underscores that the evolution of SSA occurred a long time after emission. The results presented here build a fundamental basis of knowledge about the aerosol optical properties observed over SWA during the monsoon season and can be used in climate modelling studies and satellite retrievals. In particular and regarding the very high absorbing properties of biomass burning aerosols over SWA, our findings suggest that considering the effect of internal mixing on absorption properties of black carbon particles in climate models should help better assessing the direct and semi-direct radiative effects of biomass burning particles.


2018 ◽  
Vol 18 (1) ◽  
pp. 405-425 ◽  
Author(s):  
Huizheng Che ◽  
Bing Qi ◽  
Hujia Zhao ◽  
Xiangao Xia ◽  
Thomas F. Eck ◽  
...  

Abstract. Aerosol pollution in eastern China is an unfortunate consequence of the region's rapid economic and industrial growth. Here, sun photometer measurements from seven sites in the Yangtze River Delta (YRD) from 2011 to 2015 were used to characterize the climatology of aerosol microphysical and optical properties, calculate direct aerosol radiative forcing (DARF) and classify the aerosols based on size and absorption. Bimodal size distributions were found throughout the year, but larger volumes and effective radii of fine-mode particles occurred in June and September due to hygroscopic growth and/or cloud processing. Increases in the fine-mode particles in June and September caused AOD440 nm > 1.00 at most sites, and annual mean AOD440 nm values of 0.71–0.76 were found at the urban sites and 0.68 at the rural site. Unlike northern China, the AOD440 nm was lower in July and August (∼ 0.40–0.60) than in January and February (0.71–0.89) due to particle dispersion associated with subtropical anticyclones in summer. Low volumes and large bandwidths of both fine-mode and coarse-mode aerosol size distributions occurred in July and August because of biomass burning. Single-scattering albedos at 440 nm (SSA440 nm) from 0.91 to 0.94 indicated particles with relatively strong to moderate absorption. Strongly absorbing particles from biomass burning with a significant SSA wavelength dependence were found in July and August at most sites, while coarse particles in March to May were mineral dust. Absorbing aerosols were distributed more or less homogeneously throughout the region with absorption aerosol optical depths at 440 nm ∼ 0.04–0.06, but inter-site differences in the absorption Angström exponent indicate a degree of spatial heterogeneity in particle composition. The annual mean DARF was −93 ± 44 to −79 ± 39 W m−2 at the Earth's surface and ∼ −40 W m−2 at the top of the atmosphere (for the solar zenith angle range of 50 to 80∘) under cloud-free conditions. The fine mode composed a major contribution of the absorbing particles in the classification scheme based on SSA, fine-mode fraction and extinction Angström exponent. This study contributes to our understanding of aerosols and regional climate/air quality, and the results will be useful for validating satellite retrievals and for improving climate models and remote sensing algorithms.


2021 ◽  
Author(s):  
Mariana Adam ◽  
Iwona S. Stachlewska ◽  
Lucia Mona ◽  
Nikolaos Papagiannopoulos ◽  
Juan Antonio Bravo-Aranda ◽  
...  

Abstract. Biomass burning episodes measured at 14 stations of the European Aerosol Research Lidar Network (EARLINET) over 2008–2017 were analysed using the methodology described in "Biomass burning events measured by lidars in EARLINET – Part 1: Data analysis methodology" (Adam et al., 2020, this issue). The smoke layers were identified in lidar optical properties profiles. A number of 795 layers for which we measured at least one intensive parameter was analysed. These layers were geographically distributed as follows: 399 layers observed in South-East Europe, 119 layers observed in South-West Europe, 243 layers observed in North-East Europe, and 34 layers observed in Central Europe. The mean layer intensive parameters are discussed following two research directions: (I) the long-range transport of smoke particles from North America, and (II) the smoke properties (fresh versus aged), separating the smoke events into four continental source regions (European, North American, African, Asian or a mixture of two), based on back trajectory analysis. The smoke detected in Central Europe (Cabauw, Leipzig, and Hohenpeißenberg) was mostly transported from North America (87 % of fires). In North-East Europe (Belsk, Minsk, Warsaw) smoke advected mostly from Eastern Europe (Ukraine and Russia), but there was a significant contribution (31 %) from North America. In South-West Europe (Barcelona, Evora, Granada) smoke originated mainly from the Iberian Peninsula and North Africa (while 9 % were originating in North America). In the South-East Europe (Athens, Bucharest, Potenza, Sofia, Thessaloniki) the origin of the smoke was mostly local (only 3 % represented North America smoke). The following features, correlated with the increased smoke travel time (corresponding to aging) were found: the colour ratio of the lidar ratio (i.e., the ratio of the lidar ratio at 532 nm to the lidar ratio at 355 nm) and the colour ratio of the backscatter Ångström exponent (i.e., the ratio of the backscatter-related Angstrom exponent for the pair 532 nm – 1064 nm to the one for the pair 355 nm – 532 nm) increase, while the extinction Ångström exponent and the colour ratio of the particle depolarization ratio (i.e., the ratio of the particle linear depolarization ratio at 532 nm to the particle depolarization ratio at 355 nm) decrease. The smoke originating from all continental regions can be characterized on average as aged smoke, with a very few exceptions. In general, the long range transported smoke shows higher lidar ratio and lower depolarization ratio compared to the local smoke.


2016 ◽  
Author(s):  
Jinghao Zhai ◽  
Xiaohui Lu ◽  
Ling Li ◽  
Qi Zhang ◽  
Ci Zhang ◽  
...  

Abstract. Biomass burning aerosol has important impact on the global radiative budget. A better understanding of the mixing state and chemical composition of biomass burning particles relative to their optical properties is the goal of a number of current studies. In this work, effective density, chemical composition, and optical properties of rice straw burning particles in the size range of 50–400 nm were measured using a suite of comprehensive methods. A Differential Mobility Analyzer (DMA)-Aerosol Particle Mass analyzer (APM)-Condensation Particle Counter (CPC) system offered detailed information on the effective density as well as mixing state of size-resolved particles. The effective density and chemical composition of individual particles were characterized with a DMA in-line with a Single Particle Aerosol Mass Spectrometer (SPAMS), simultaneously. The multiple modes observed in the size-resolved particle effective density distribution indicated size-dependent external mixing of black carbon (BC), organic carbon (OC) and potassium salts in particles. Particles of 50 nm had the smallest effective density (1.16 g/cm3), due to a relative large proportion of aggregate BC. The average effective densities of 100–400 nm particles ranged from 1.35–1.51 g/cm3 with OC and inorganic salts as dominant components. Both density distribution and single-particle mass spectrometry showed more complex mixing states in larger particles. Upon heating, the separation of the effective density distribution modes testified the existence of less volatile BC or soot and potassium salts. Size-resolved optical properties of biomass burning particles were measured by the Cavity Attenuated Phase Shift spectroscopy (CAPS, λ = 450 & 530 nm). The single scattering albedo (SSA) showed the lowest value for 50 nm particles (0.741 ± 0.007 & 0.889 ± 0.006) because of larger proportion of BC content. Brown carbon played an important role for the SSA of 100–400 nm particles. The Ångström absorption exponent (AAE) values for all particles were above 1.6, indicating the significant presence of brown carbon. Though freshly emitted, the light absorption enhancement (Eabs) was observed for particles larger than 200 nm. Concurrent measurements in our work provide a basis for discussing the physicochemical properties of biomass burning aerosol and its effects on global climate and atmospheric environment.


2020 ◽  
Vol 20 (23) ◽  
pp. 15323-15339 ◽  
Author(s):  
Xiaoxia Shang ◽  
Elina Giannakaki ◽  
Stephanie Bohlmann ◽  
Maria Filioglou ◽  
Annika Saarto ◽  
...  

Abstract. We present a novel algorithm for characterizing the optical properties of pure pollen particles, based on the depolarization ratio values obtained in lidar measurements. The algorithm was first tested and validated through a simulator and then applied to the lidar observations during a 4-month pollen campaign from May to August 2016 at the European Aerosol Research Lidar Network (EARLINET) station in Kuopio (62∘44′ N, 27∘33′ E), in Eastern Finland. With a Burkard sampler, 20 types of pollen were observed and identified from concurrent measurements, with birch (Betula), pine (Pinus), spruce (Picea), and nettle (Urtica) pollen being the most abundant, contributing more than 90 % of the total pollen load, regarding number concentrations. Mean values of lidar-derived optical properties in the pollen layer were retrieved for four intense pollination periods (IPPs). Lidar ratios at both 355 and 532 nm ranged from 55 to 70 sr for all pollen types, without significant wavelength dependence. An enhanced depolarization ratio was found when there were pollen grains in the atmosphere, and an even higher depolarization ratio (with mean values of 0.25 or 0.14) was observed with the presence of the more non-spherical spruce or pine pollen. Under the assumption that the backscatter-related Ångström exponent between 355 and 532 nm should be zero for pure pollen, the depolarization ratio of pure pollen particles at 532 nm was assessed, resulting in 0.24±0.01 and 0.36±0.01 for birch and pine pollen, respectively. Pollen optical properties at 1064 and 355 nm were also estimated. The backscatter-related Ångström exponent between 532 and 1064 nm was assessed to be ∼0.8 (∼0.5) for pure birch (pine) pollen; thus the longer wavelength would be a better choice to trace pollen in the air. Pollen depolarization ratios of 0.17 and 0.30 at 355 nm were found for birch and pine pollen, respectively. The depolarization values show a wavelength dependence for pollen. This can be the key parameter for pollen detection and characterization.


Sign in / Sign up

Export Citation Format

Share Document