scholarly journals Dynamic deformation and fracturing properties of concrete under biaxial confinements

2021 ◽  
Vol 250 ◽  
pp. 06008
Author(s):  
Huachuan Wang ◽  
Kai Liu ◽  
Qianbing Zhang
Keyword(s):  
Dynamic Deformation ◽  
Compressive Strain ◽  
Three Dimensional ◽  
Complex Loading ◽  
Image Correlation ◽  
Concrete Material ◽  
Interfacial Cracks ◽  
X Ray Computed ◽  
Transgranular Cracks ◽  
Ct Slices

The study of deformation and fracturing properties of concrete is essential to understand failure mechanisms of concrete material, especially under extreme and complex loading conditions, e.g. high strain rates and multiple confinements. In this study, dynamic deformation and fracturing behaviour of ordinary concrete under biaxial confinements are investigated by using a triaxial Hopkinson bar system, three-dimensional digital image correlation, and synchrotron X-ray computed tomography techniques. Results show that compressive strain localisation areas appear around aggregates due to the elastic difference between aggregate and matrix, where accompanied with initiation of interfacial cracks and propagation of main cracks. Transgranular cracks can also be observed in the central of specimen in CT slices due to the effect of strain concentration. In addition, CT slices with distinct properties in various directions indicate the anisotropic fracturing behaviour of concrete due to the effect of biaxial confinements.

scholarly journals 3D Studies of Indentation by Combined X-Ray Tomography and Digital Volume Correlation

2013 ◽  
Vol 592-593 ◽  
pp. 14-21 ◽  
Author(s):  
Mahmoud Mostafavi ◽  
Yelena Vertyagina ◽  
Christina Reinhard ◽  
Robert Bradley ◽  
Xia Jiang ◽  
...  
Keyword(s):  
Crack Opening ◽  
Three Dimensional ◽  
Image Correlation ◽  
Digital Volume Correlation ◽  
Surface Characterisation ◽  
X Ray ◽  
Element Simulation ◽  
Potential Applications ◽  
Deformation Processes ◽  
X Ray Computed

Hardness testing obtains material properties from small specimens via measurement of load-displacement response to an imposed indentation; it is a surface characterisation technique so, except in optically transparent materials, there is no direct observation of the assumed damage and deformation processes within the material. Three-dimensional digital image correlation (digital volume correlation) is applied to study deformation beneath indentations, mapping the relative displacements between high-resolution synchrotron X-ray computed tomographs (0.9 μm voxel size). Two classes of material are examined: ductile aluminium-silicon carbide composite (Al-SiC) and brittle alumina (Al2O3). The measured displacements for Hertzian indentation in Al-SiC are in good agreement with an elastic-plastic finite element simulation. In alumina, radial cracking is observed beneath a Vickers indentation and the crack opening displacements are measured, in situ under load, for the first time. Potential applications are discussed of this characterization technique, which does not require resolution of microstructural features.

scholarly journals Three-dimensional image correlation from X-ray computed tomography of solid foam

2008 ◽  
Vol 39 (8) ◽  
pp. 1253-1265 ◽  
Author(s):  
Stéphane Roux ◽  
François Hild ◽  
Philippe Viot ◽  
Dominique Bernard
Keyword(s):  
Computed Tomography ◽  
Three Dimensional ◽  
Image Correlation ◽  
X Ray ◽  
Dimensional Image ◽  
X Ray Computed ◽  
Solid Foam

scholarly journals Three‐dimensional X‐ray‐computed tomography of 3300‐ to 6000‐year‐old Citrullus seeds from Libya and Egypt compared to extant seeds throws doubts on species assignments

2021 ◽  
Author(s):  
Katherine A. Wolcott ◽  
Guillaume Chomicki ◽  
Yannick M. Staedler ◽  
Krystyna Wasylikowa ◽  
Mark Nesbitt ◽  
...  
Keyword(s):  
Computed Tomography ◽  
Three Dimensional ◽  
X Ray ◽  
X Ray Computed

scholarly journals An Improved Cohesive Zone Model for Interface Mixed-Mode Fractures of Railway Slab Tracks

2021 ◽  
Vol 11 (1) ◽  
pp. 456
Author(s):  
Yanglong Zhong ◽  
Liang Gao ◽  
Xiaopei Cai ◽  
Bolun An ◽  
Zhihan Zhang ◽  
...  
Keyword(s):  
Interface Crack ◽  
Cohesive Zone ◽  
Mixed Mode ◽  
Cohesive Zone Model ◽  
Complex Loading ◽  
Bending Test ◽  
Mixed Mode Fracture ◽  
Zone Model ◽  
Slab Track ◽  
Interfacial Cracks

The interface crack of a slab track is a fracture of mixed-mode that experiences a complex loading–unloading–reloading process. A reasonable simulation of the interaction between the layers of slab tracks is the key to studying the interface crack. However, the existing models of interface disease of slab track have problems, such as the stress oscillation of the crack tip and self-repairing, which do not simulate the mixed mode of interface cracks accurately. Aiming at these shortcomings, we propose an improved cohesive zone model combined with an unloading/reloading relationship based on the original Park–Paulino–Roesler (PPR) model in this paper. It is shown that the improved model guaranteed the consistency of the cohesive constitutive model and described the mixed-mode fracture better. This conclusion is based on the assessment of work-of-separation and the simulation of the mixed-mode bending test. Through the test of loading, unloading, and reloading, we observed that the improved unloading/reloading relationship effectively eliminated the issue of self-repairing and preserved all essential features. The proposed model provides a tool for the study of interface cracking mechanism of ballastless tracks and theoretical guidance for the monitoring, maintenance, and repair of layer defects, such as interfacial cracks and slab arches.

Influence of the Welded Joint on the Mechanical Behavior of Steel Piles during Static and Dynamic Deformation

2007 ◽  
Vol 345-346 ◽  
pp. 1469-1472
Author(s):  
Gab Chul Jang ◽  
Kyong Ho Chang ◽  
Chin Hyung Lee
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Mechanical Behavior ◽  
Welded Joint ◽  
Dynamic Deformation ◽  
Three Dimensional ◽  
Steel Structures ◽  
Residual Stress Distribution ◽  
Dynamic Mechanical Behavior ◽  
Steel Piles

During manufacturing the welded joint of steel structures, residual stress is produced and weld metal is used inevitably. And residual stress and weld metal influence on the static and dynamic mechanical behavior of steel structures. Therefore, to predict the mechanical behavior of steel pile with a welded joint during static and dynamic deformation, the research on the influence of the welded joints on the static and dynamic behavior of steel pile is clarified. In this paper, the residual stress distribution in a welded joint of steel piles was investigated by using three-dimensional welding analysis. The static and dynamic mechanical behavior of steel piles with a welded joint is investigated by three-dimensional elastic-plastic finite element analysis using a proposed dynamic hysteresis model. Numerical analyses of the steel pile with a welded joint were compared to that without a welded joint with respect to load carrying capacity and residual stress distribution. The influence of the welded joint on the mechanical behavior of steel piles during static and dynamic deformation was clarified by comparing analytical results

Visualizing Fluid Flows With X-Rays

2007 ◽  
Author(s):  
Theodore J. Heindel ◽  
Terrence C. Jensen ◽  
Joseph N. Gray
Keyword(s):  
Computed Tomography ◽  
Flow Visualization ◽  
Three Dimensional ◽  
Fluid Flows ◽  
X Rays ◽  
Radiographic Images ◽  
Optical Access ◽  
X Ray ◽  
X Ray Computed ◽  
Density Map

There are several methods available to visualize fluid flows when one has optical access. However, when optical access is limited to near the boundaries or not available at all, alternative visualization methods are required. This paper will describe flow visualization using an X-ray system that is capable of digital X-ray radiography, digital X-ray stereography, and digital X-ray computed tomography (CT). The unique X-ray flow visualization facility will be briefly described, and then flow visualization of various systems will be shown. Radiographs provide a two-dimensional density map of a three dimensional process or object. Radiographic images of various multiphase flows will be presented. When two X-ray sources and detectors simultaneously acquire images of the same process or object from different orientations, stereographic imaging can be completed; this type of imaging will be demonstrated by trickling water through packed columns and by absorbing water in a porous medium. Finally, local time-averaged phase distributions can be determined from X-ray computed tomography (CT) imaging, and this will be shown by comparing CT images from two different gas-liquid sparged columns.

scholarly journals In-Process Measurement of Three-Dimensional Deformations Based on Speckle Photography

2021 ◽  
Vol 11 (11) ◽  
pp. 4981
Author(s):  
Andreas Tausendfreund ◽  
Dirk Stöbener ◽  
Andreas Fischer
Keyword(s):  
Evaluation Method ◽  
Process Analysis ◽  
Plane Deformation ◽  
Three Dimensional ◽  
Machining Process ◽  
Image Correlation ◽  
Speckle Photography ◽  
Process Measurement ◽  
Out Of Plane ◽  
Plane Deformations

In the concept of the process signature, the relationship between a material load and the modification remaining in the workpiece is used to better understand and optimize manufacturing processes. The basic prerequisite for this is to be able to measure the loads occurring during the machining process in the form of mechanical deformations. Speckle photography is suitable for this in-process measurement task and is already used in a variety of ways for in-plane deformation measurements. The shortcoming of this fast and robust measurement technique based on image correlation techniques is that out-of-plane deformations in the direction of the measurement system cannot be detected and increases the measurement error of in-plane deformations. In this paper, we investigate a method that infers local out-of-plane motions of the workpiece surface from the decorrelation of speckle patterns and is thus able to reconstruct three-dimensional deformation fields. The implementation of the evaluation method enables a fast reconstruction of 3D deformation fields, so that the in-process capability remains given. First measurements in a deep rolling process show that dynamic deformations underneath the die can be captured and demonstrate the suitability of the speckle method for manufacturing process analysis.

scholarly journals Increase in Total Elongation Caused by Pure Shear Deformation in Ultra-Fine-Grained Cu Processed by Equal-Channel Angular Pressing

Metals ◽  
2020 ◽  
Vol 10 (5) ◽  
pp. 654
Author(s):  
Ryosuke Matsutani ◽  
Nobuo Nakada ◽  
Susumu Onaka
Keyword(s):  
Shear Deformation ◽  
Equal Channel Angular Pressing ◽  
Pure Shear ◽  
Three Dimensional ◽  
Tensile Tests ◽  
Total Elongation ◽  
Local Deformation ◽  
Image Correlation ◽  
Fine Grained ◽  
Angular Pressing

Ultra-fine-grained (UFG) Cu shows little total elongation in tensile tests because simple shear deformation is concentrated in narrow regions during the initial stage of plastic deformation. Here, we attempted to improve the total elongation of UFG Cu obtained by equal-channel angular pressing. By making shallow dents on the side surfaces of the plate-like specimens, this induced pure shear deformation and increased their total elongation. During the tensile tests, we observed the overall and local deformation of the dented and undented UFG Cu specimens. Using three-dimensional digital image correlation, we found that the dented specimens showed suppression of thickness reduction and delay in fracture by enhancement of pure shear deformation. However, the dented and undented specimens had the same ultimate tensile strength. These results provide us a new concept to increase total elongation of UFG materials.

Three-dimensional analysis of plant structure using high-resolution X-ray computed tomography

2003 ◽  
Vol 8 (1) ◽  
pp. 2-6 ◽  
Author(s):  
Wolfgang H Stuppy ◽  
Jessica A Maisano ◽  
Matthew W Colbert ◽  
Paula J Rudall ◽  
Timothy B Rowe
Keyword(s):  
Computed Tomography ◽  
High Resolution ◽  
Dimensional Analysis ◽  
Three Dimensional ◽  
Plant Structure ◽  
X Ray ◽  
X Ray Computed
Sign in / Sign up

Export Citation Format

Share Document