scholarly journals Development of a Design Procedure for Class E Amplifiers

2018 ◽  
Vol 223 ◽  
pp. 01016
Author(s):  
Mattison S. Siri ◽  
David S. Cochran
Keyword(s):  
Design Procedure ◽  
Design Parameters ◽  
Specific Load ◽  
Systems Architecture ◽  
Design Decomposition ◽  
Path Dependent ◽  
Capacitance Coupling ◽  
Class E

Here, the step-by-step design procedure for a Class E amplifier is presented. An existing Class E amplifier system is described using a systems architecture approach. The design decomposition for the case study is written so that Physical Solutions (PSs; equivalent to Design Parameters) are in terms of component parameters (such as frequency or capacitance). Coupling issues are found to arise given constraints on transistor use. The design decomposition is altered to reflect the case where an amplifier is required to power a specific load. A discussion of transistor failure enables a design procedure to be developed by observing path-dependent coupling. The design procedure is tested through the design of a real amplifier. The designed amplifier is built and its performance measured.

scholarly journals A New Strategy for Multi- Objective Dynamic and Kinematic Optimization of Robotic Manipulators with Application in Haptic Interfaces

2021 ◽  
Author(s):  
Behrooz Alae
Keyword(s):  
Dynamic Capabilities ◽  
Design Procedure ◽  
Design Parameters ◽  
Haptic Interfaces ◽  
Optimization Strategy ◽  
Multi Objective ◽  
New Strategy ◽  
Increasing Demand ◽  
Robotic Applications

There is an increasing demand for higher performance in modern robotic applications. To meet the need for more accuracy and fast dynamic response, considering inertial effects is necessary. This thesis proposes a new global multi-objective optimization strategy to tune the geometric and dynamic capabilities of a manipulator. Then, as a case study, the kinematics and dynamic behavior of a five-bar-linkage haptic interface is analyzed and a new design procedure is obtained using a new global and constrained multi-objective technique. The minimax culling algorithm was used to design parameters for optimal kinematics and dynamic dexterity measure.

scholarly journals A New Strategy for Multi- Objective Dynamic and Kinematic Optimization of Robotic Manipulators with Application in Haptic Interfaces

2021 ◽  
Author(s):  
Behrooz Alae
Keyword(s):  
Dynamic Capabilities ◽  
Design Procedure ◽  
Design Parameters ◽  
Haptic Interfaces ◽  
Optimization Strategy ◽  
Multi Objective ◽  
New Strategy ◽  
Increasing Demand ◽  
Robotic Applications

There is an increasing demand for higher performance in modern robotic applications. To meet the need for more accuracy and fast dynamic response, considering inertial effects is necessary. This thesis proposes a new global multi-objective optimization strategy to tune the geometric and dynamic capabilities of a manipulator. Then, as a case study, the kinematics and dynamic behavior of a five-bar-linkage haptic interface is analyzed and a new design procedure is obtained using a new global and constrained multi-objective technique. The minimax culling algorithm was used to design parameters for optimal kinematics and dynamic dexterity measure.

Wastewater treatment and nutrient removal in the combined reactor

1998 ◽  
Vol 38 (1) ◽  
pp. 87-95 ◽  
Author(s):  
M. Roš ◽  
J. Vrtovšek
Keyword(s):  
Organic Compounds ◽  
Industrial Wastewater ◽  
Design Procedure ◽  
Order Reaction ◽  
Treated Wastewater ◽  
Nitrification Rate ◽  
Zero Order Reaction ◽  
Aerobic Reactor ◽  
Complex Organic

A combined anaerobic anoxic aerobic reactor for the treatment of the industrial wastewater that contains nitrogen and complex organic compounds as well as its design procedure is presented. The purpose of our experiments was to find a simple methodology that would provide combined reactor design. The reactor is based on the combination of anaerobic, anoxic and aerobic process in one unit only. It was found that the HRT even under 1 hour in the anaerobic zone is long enough for the efficient transformation of complex organic compounds into readily biodegradable COD which is then used in dentrification process. In the N-NO3 concentration range 1.5-50 mg/l the denitrification rate could be expressed as half-order reaction when the CODrb was in excess. N-NO3 removal efficiency is controlled by the recycle flow from the aerobic to the anoxic zone. Nitrification rate can be expressed as first, half or zero-order reaction with respect to effluent N-NH4 concentration. Nitrification rate depends on the dissolved oxygen concentration and hydrodynamic conditions in the reactor. Case study for design of a pilot plant of the combined reactor for treatment of pre-treated pharmaceutical wastewater is shown. Characteristics of pre-treated wastewater were: COD=200 mg/l, BOD5=20 mg/l, N-Kjeldahl=80 mg/l, N-NH4=70 mg/l, N-NOx<1 mg/l, P-PO4=5 mg/l. Legal requirements for treated wastewater were: COD=<100 mg/l, BOD5<5 mg/l, N-NH4=<1 mg/l, N-NOx=<10 mg/l.

scholarly journals A Two-Round Optimization Design Method for Aerostatic Spindles Considering the Fluid–Structure Interaction Effect

2021 ◽  
Vol 11 (7) ◽  
pp. 3017
Author(s):  
Qiang Gao ◽  
Siyu Gao ◽  
Lihua Lu ◽  
Min Zhu ◽  
Feihu Zhang
Keyword(s):  
Optimal Design ◽  
Optimization Design ◽  
Design Method ◽  
Fluid Structure Interaction ◽  
Design Procedure ◽  
Design Parameters ◽  
Geometrical Parameters ◽  
Fluid Structure ◽  
Structure Interaction ◽  
Aerostatic Spindle

The fluid–structure interaction (FSI) effect has a significant impact on the static and dynamic performance of aerostatic spindles, which should be fully considered when developing a new product. To enhance the overall performance of aerostatic spindles, a two-round optimization design method for aerostatic spindles considering the FSI effect is proposed in this article. An aerostatic spindle is optimized to elaborate the design procedure of the proposed method. In the first-round design, the geometrical parameters of the aerostatic bearing were optimized to improve its stiffness. Then, the key structural dimension of the aerostatic spindle is optimized in the second-round design to improve the natural frequency of the spindle. Finally, optimal design parameters are acquired and experimentally verified. This research guides the optimal design of aerostatic spindles considering the FSI effect.

Analysis and Design Procedure of a mm-Wave Class-E Power Amplifier

2021 ◽  
pp. 105036
Author(s):  
Habib Ghasemizadeh ◽  
Abdolreza Nabavi ◽  
Member IEEE ◽  
Mohsen Haghighat
Keyword(s):  
Power Amplifier ◽  
Design Procedure ◽  
Analysis And Design ◽  
Class E

A Systematic Function Recommendation Process for Data-Driven Product and Service Design

2017 ◽  
Vol 139 (11) ◽  
Author(s):  
Zhinan Zhang ◽  
Ling Liu ◽  
Wei Wei ◽  
Fei Tao ◽  
Tianmeng Li ◽  
...  
Keyword(s):  
Subjective Experience ◽  
Vital Role ◽  
Data Driven ◽  
Design Parameters ◽  
Sound Design ◽  
New Paradigm ◽  
Senior Managers ◽  
Product Service ◽  
Target User

This paper presents a systematic function recommendation process (FRP) to recommend new functions to an existing product and service. Function plays a vital role in mapping user needs to design parameters (DPs) under constraints. It is imperative for manufacturers to continuously equip an existing product/service with exciting new functions. Traditionally, functions are mostly formulated by experienced designers and senior managers based on their subjective experience, knowledge, creativity, and even heuristics. Nevertheless, against the sweeping trend of information explosion, it is increasingly inefficient and unproductive for designers to manually formulate functions. In e-commerce, recommendation systems (RS) are ubiquitously used to recommend new products to users. In this study, the practically viable recommendation approaches are integrated with the theoretically sound design methodologies to serve a new paradigm of recommending new functions to an existing product/service. The aim is to address the problem of how to estimate an unknown rating that a target user would give to a candidate function that is not carried by the target product/service yet. A systematic function → product recommendation process is prescribed, followed by a detailed case study. It is indicated that practically meaningful functional recommendations (FRs) can indeed by generated through the proposed FRP.

A Practical Approach to Expedite a Pore to Process Simulation Model for a Rich Gas Condensate Reservoir – Case Study

2021 ◽  
Author(s):  
Mohamed Ibrahim Mohamed ◽  
Ahmed Mahmoud El-Menoufi ◽  
Eman Abed Ezz El-Regal ◽  
Ahmed Mohamed Ali ◽  
Khaled Mohamed Mansour ◽  
...  
Keyword(s):  
Simulation Model ◽  
Production Optimization ◽  
Operating Conditions ◽  
Gas Condensate ◽  
Western Desert ◽  
Design Parameters ◽  
Compositional Approach ◽  
Process Plant ◽  
Black Oil

Abstract Field development planning of gas condensate fields using numerical simulation has many aspects to consider that may lead to a significant impact on production optimization. An important aspect is to account for the effects of network constraints and process plant operating conditions through an integrated asset model. This model should honor proper representation of the fluid within the reservoir, through the wells and up to the network and facility. Obaiyed is one of the biggest onshore gas field in Egypt, it is a highly heterogeneous gas condensate field located in the western desert of Egypt with more than 100 wells. Three initial condensate gas ratios are existing based on early PVT samples and production testing. The initial CGRs as follows;160, 115 and 42 STB/MMSCF. With continuous pressure depletion, the produced hydrocarbon composition stream changes, causing a deviation between the design parameters and the operating parameters of the equipment within the process plant, resulting in a decrease in the recovery of liquid condensate. Therefore, the facility engineers demand a dynamic update of a detailed composition stream to optimize the system and achieve greater economic value. The best way to obtain this compositional stream is by using a fully compositional integrated asset model. Utilizing a fully compositional model in Obaiyed is challenging, computationally expensive, and impractical, especially during the history match of the reservoir numerical model. In this paper, a case study for Obaiyed field is presented in which we used an alternative integrated asset modeling approach comprising a modified black-oil (MBO) that results in significant timesaving in the full-field reservoir simulation model. We then used a proper de-lumping scheme to convert the modified black oil tables into as many components as required by the surface network and process plant facility. The results of proposed approach are compared with a fully compositional approach for validity check. The results clearly identified the system bottlenecks. The model can be used to propose the best tie-in location of future wells in addition to providing first-pass flow assurance indications throughout the field's life and under different network configurations. The model enabled the facility engineers to keep the conditions of the surface facility within the optimized operating envelope throughout the field's lifetime.

Active-Device Losses in Resonant Power Converters: A Case Study with Class-E Inverters

2021 ◽  
Author(s):  
Nirmana Perera ◽  
Remco van Erp ◽  
Jessy Ancay ◽  
Armin Jafari ◽  
Elison Matioli
Keyword(s):  
Power Converters ◽  
Active Device ◽  
Class E

Parametric Aircraft Design Optimisation Study Using Span and Mean Chord as Main Design Drivers

2014 ◽  
Vol 1016 ◽  
pp. 365-369 ◽  
Author(s):  
Pedro Albuquerque ◽  
Pedro Gamboa ◽  
Miguel Silvestre
Keyword(s):  
Design Methodology ◽  
Aircraft Design ◽  
Design Parameters ◽  
Flight Performance ◽  
Air Cargo ◽  
Main Design ◽  
Design Specifications ◽  
Performance Requirements ◽  
Aircraft Performance

The present work describes an aircraft design methodology that uses the wingspan and its mean aerodynamic chord as main design parameters. In the implemented tool, low fidelity models have been developed for the aerodynamics, stability, propulsion, weight, balance and flight performance. A Fortran® routine that calculates the aircraft performance for the user defined mission and vehicle’s performance requirements has been developed. In order to demonstrate this methodology, the results for a case study using the design specifications of the Air Cargo Challenge 2013 are shown.

Sign in / Sign up

Export Citation Format

Share Document