scholarly journals Flow Characteristics of Drag-Reducing Surfactant Solutions

2021 ◽  
Vol 333 ◽  
pp. 02002
Author(s):  
Takashi Saeki ◽  
Aya Kaide
Keyword(s):  
Particle Image ◽  
Pipe Wall ◽  
Reduction Rate ◽  
Flow Characteristics ◽  
Contour Plot ◽  
Constant Concentration ◽  
Lower Velocity ◽  
Surfactant Solutions ◽  
Image Velocimetry ◽  
Velocity Region

The objective of this study is to clarify the flow characteristics of drag-reducing flow and to elucidate the mechanism underlying this phenomenon. The surfactant and counter ion we used were Lipothoquad O/12 and sodium salicylate, respectively. The drag reduction rate (DR%) was measured by using a recirculating system with a diameter of 25.6 mm. We also measured the flow characteristics of the surfactant solutions with different concentrations and temperatures by using particle image velocimetry (PIV). From the experimental results, DR% at an average velocity of 2.0 m/s increased from 0 to 68% as the temperature increased from 10 to 40 °C at a constant concentration of surfactant (300 mg/L). From the velocity contour plot obtained from PIV, we found that the thickness of the lower-velocity region of the drag-reducing flow near the pipe wall was thick at 20 °C, whereas vortex motions seemed controlled at 30 °C. On the other hand, the lower-velocity region thickened as the concentration of the surfactant increased at 25°C. Even if the same level of drag-reducing effects occurred, the flow patterns were quite different depending on the concentration and temperature.

Flow Characteristics of Pressure-Driven Water in Serpentine Micro-Channels

2006 ◽  
Author(s):  
Renqiang Xiong ◽  
J. N. Chung
Keyword(s):  
Particle Image Velocimetry ◽  
Particle Image ◽  
Flow Characteristics ◽  
Flow Structures ◽  
Micro Channel ◽  
Pressure Drops ◽  
Micro Particle Image Velocimetry ◽  
Image Velocimetry ◽  
Micro Channels ◽  
Shape And Size

Flow structures and pressure drops were investigated in rectangular serpentine micro-channels with miter bends which had hydraulic diameters of 0.209mm, 0.395mm and 0.549mm respectively. To evaluate the bend effect, the additional pressure drop due to the miter bend must be obtained. Three groups of micro-channels were fabricated to remove the inlet and outlet losses. A validated micro-particle image velocimetry (μPIV) system was used to achieve the flow structure in a serpentine micro-channel with hydraulic diameter of 0.173mm. The experimental results show the vortices around the outer and inner walls of the bend do not form when Re<100. Those vortices appear and continue to develop with the Re number when Re> 100-300, and the shape and size of the vortices almost remain constant when Re>1000. The bend loss coefficient Kb was observed to be related with the Re number when Re<100, with the Re number and channel size when Re>100. It almost keeps constant and changes in the range of ± 10% When Re is larger than some value in 1300-1500. And a size effect on Kb was also observed.

A particle image velocimetry study on the pulsatile flow characteristics in straight tubes with an asymmetric bulge

2000 ◽  
Vol 214 (5) ◽  
pp. 655-671 ◽  
Author(s):  
S C M Yu ◽  
J B Zhao
Keyword(s):  
Particle Image Velocimetry ◽  
Steady Flow ◽  
Pulsatile Flow ◽  
Flow Condition ◽  
Particle Image ◽  
Flow Characteristics ◽  
Reynolds Numbers ◽  
Working Fluid ◽  
Flow Conditions ◽  
Image Velocimetry

Flow characteristics in straight tubes with an asymmetric bulge have been investigated using particle image velocimetry (PIV) over a range of Reynolds numbers from 600 to 1200 and at a Womersley number of 22. A mixture of glycerine and water (approximately 40:60 by volume) was used as the working fluid. The study was carried out because of their relevance in some aspects of physiological flows, such as arterial flow through a sidewall aneurysm. Results for both steady and pulsatile flow conditions were obtained. It was found that at a steady flow condition, a weak recirculating vortex formed inside the bulge. The recirculation became stronger at higher Reynolds numbers but weaker at larger bulge sizes. The centre of the vortex was located close to the distal neck. At pulsatile flow conditions, the vortex appeared and disappeared at different phases of the cycle, and the sequence was only punctuated by strong forward flow behaviour (near the peak flow condition). In particular, strong flow interactions between the parent tube and the bulge were observed during the deceleration phase. Stents and springs were used to dampen the flow movement inside the bulge. It was found that the recirculation vortex could be eliminated completely in steady flow conditions using both devices. However, under pulsatile flow conditions, flow velocities inside the bulge could not be suppressed completely by both devices, but could be reduced by more than 80 per cent.

Particle Image Velocimetry Measurements of the Mean Flow Characteristics in a Bubble Plume

2007 ◽  
Vol 133 (6) ◽  
pp. 665-676 ◽  
Author(s):  
Dong-Guan Seol ◽  
Tirtharaj Bhaumik ◽  
Christian Bergmann ◽  
Scott A. Socolofsky
Keyword(s):  
Particle Image Velocimetry ◽  
Particle Image ◽  
Flow Characteristics ◽  
Bubble Plume ◽  
Mean Flow ◽  
Image Velocimetry ◽  
The Mean

An Experimental Study on the Performance of Drag-Reducing Polymers in Single- and Multiphase Horizontal Flow Using Particle Image Velocimetry

2018 ◽  
Vol 140 (5) ◽  
Author(s):  
Ihab H. Alsurakji ◽  
A. Al-Sarkhi ◽  
M. Habib ◽  
Hassan M. Badr
Keyword(s):  
Particle Image Velocimetry ◽  
Particle Image ◽  
Pipe Wall ◽  
Fluid Dynamic ◽  
Water Soluble ◽  
Experimental Investigations ◽  
Two Phase ◽  
Image Velocimetry ◽  
Flow Field Characteristics ◽  
Phase Water

This paper presents experimental investigations conducted to understand the influence of water-soluble drag-reducing polymers (DRPs) in single- and two-phase (stratified wavy) flow on flow-field characteristics. These experiments have been presented for water and air–water flowing in a horizontal polyvinyl chloride 22.5-mm ID, 8.33-m long pipe. The effects of liquid flow rates and DRP concentrations on streamlines and the instantaneous velocity were investigated by using particle image velocimetry (PIV) technique. A comparison of the PIV results was performed by comparing them with the computational results obtained by fluent software. One of the comparisons has been done between the PIV results, where a turbulent flow with DRP was examined, and the laminar–computational fluid dynamic (CFD) prediction. An agreement was found in the region near the pipe wall in some cases. The results showed the powerfulness of using the PIV techniques in understanding the mechanism of DRP in single- and two-phase flow especially at the regions near the pipe wall and near the phases interface. The results of this study indicate that an increase in DRP concentrations results in an increase in drag reduction up to 45% in single-phase water flow and up to 42% in air–water stratified flow.

Effect of inlet port on the flow in the cylinder of an internal combustion engine

2006 ◽  
Vol 220 (1) ◽  
pp. 73-82 ◽  
Author(s):  
A Yasar ◽  
B Sahin ◽  
H Akilli ◽  
K Aydin
Keyword(s):  
Particle Image Velocimetry ◽  
Velocity Distribution ◽  
Particle Image ◽  
Combustion Engine ◽  
Flow Characteristics ◽  
Intake Port ◽  
Intake Valve ◽  
Piv Technique ◽  
Image Velocimetry ◽  
Image Density

In this study, the characteristics of flow emerging from the inlet of the intake port in the cylinder were investigated experimentally. A particle image velocimetry (PIV) technique was used to measure the velocity distribution in order to observe and analyse the flow behaviour. High-image-density PIV provided acquisition of patterns of instantaneous and averaged vorticity and velocity, revealing the detail of the flow characteristics in the cylinder cavity. With this measuring technique, it is possible to study the effect of intake valve geometry on the flow behaviours. The results showed that the flow structure changed substantially along the cylinder stroke due to the geometry of the intake valve port.

scholarly journals Visualization of flow characteristics between the ribbed plates via particle image velocimetry

2019 ◽  
pp. 300-300
Author(s):  
Ilker Goktepeli ◽  
Ulas Atmaca ◽  
Sercan Yagmur
Keyword(s):  
Heat Transfer ◽  
Particle Image Velocimetry ◽  
Flow Separation ◽  
Particle Image ◽  
Reference Model ◽  
Water Channel ◽  
Flow Characteristics ◽  
Advanced Technology ◽  
Particle Image Velocimetry System ◽  
Image Velocimetry

Heat transfer is considerably influenced by flow stagnation, separation and reattachment regions due to the ribbed plates. Placing the ribs such as fins, turbulators that trigger the flow separation, enhances the heat transfer inside the channel by increasing the turbulence intensity. The flow separation is caused by disturbing the thermal and hydrodynamic development lengths. Moreover, these ribs also make an impact that increases the heat transfer by enlarging the heat transfer area. However, the ribs lead to the increment of the required pumping power in the meantime due to the increasing pressure loss in such systems. This aforementioned method is used for the heat exchangers, the solar collectors, the cooling of electronic devices. The investigation of the flow characteristics is very crucial to understand the heat transfer mechanism in the ducts for this reason. In the present paper, the flow characteristics between the plates have been experimentally researched. Particle Image Velocimetry system in the open water channel of Selcuk University Advanced Technology Research and Application Center has been used. The smooth plates have been taken as the reference model and used for the comparison with the plates having the rectangular cross-sectional ribs. The ribs with various heights of 0.1 ? h' = h/H ? 0.3 have been symmetrically placed on the internal surfaces of the plates via several spacing values of 0.5 ? S' = S/H ? 1 for varying Reynolds numbers as 10000 ? Re ? 20000. As a result, the flow characteristics have been given in terms of the contour graphics for velocity vector field, velocity components and vorticity.

Unsteady Velocity Field Measurements of Outlet Flow in an Automotive Supercharger

2006 ◽  
Author(s):  
Pranay Mahendra ◽  
Michael G. Olsen
Keyword(s):  
Particle Image Velocimetry ◽  
Automotive Industry ◽  
High Speed ◽  
Particle Image ◽  
Flow Characteristics ◽  
Field Measurements ◽  
Velocity Fields ◽  
Positive Displacement ◽  
Image Velocimetry ◽  
Outlet Flow

Recently the automotive industry has been using superchargers to boost the power generated by the engine, but the noise generated by these superchargers is of great concern. The noise generated during the working of the supercharger is primarily a fluid mechanics phenomenon. Particle Image Velocimetry (PIV) was used to study air flow characteristics of a positive displacement supercharger with an emphasis on gaining insights into strategies for noise reduction. PIV was used to measure the instantaneous and ensemble-averaged velocity fields of the flow at the outlet of the supercharger as a function of blade position, allowing for visualization of the flow as it leave the blades. The preliminary results show that the flow exits the supercharger as a high speed jet at the end closer to the pulley end, and the flow varies with the change in blade position.

Sign in / Sign up

Export Citation Format

Share Document