Influence of tool nature and coating on the temperature distribution during chip formation in orthogonal cutting of steels

1997 ◽  
Vol 85 (9-10) ◽  
pp. 37-42 ◽  
Author(s):  
R. M’Saoubi ◽  
C. Le Calvez ◽  
J.L. Lebrun
Keyword(s):  
Temperature Distribution ◽  
Chip Formation ◽  
Orthogonal Cutting

Finite Element and Experimental Analysis of Edge Defects Formation during Orthogonal Cutting of SiCp/Al Composites

2012 ◽  
Vol 500 ◽  
pp. 146-151 ◽  
Author(s):  
Ning Hou ◽  
Li Zhou ◽  
Shu Tao Huang ◽  
Li Fu Xu
Keyword(s):  
Finite Element ◽  
Chip Formation ◽  
Defect Formation ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Rake Angle ◽  
Critical Transition ◽  
Cutting Depth ◽  
Edge Defect ◽  
Edge Defects

In this paper, a finite element method was used to dynamically simulate the process of the edge defects formation during orthogonal cutting SiCp/Al composites. The influence of the cutting speed, cutting depth and rake angle of the PCD insert on the size of the edge defects have been investigated by using scanning electron. According to the simulated results, it can be provided that the cutting layer material has an effect on transfer stress and hinder the chip formation in the critical transition stage, and the critical transition point and distance are defined in this stage. The negative shear phenomenon is found when the chip transit to the edge defects in the flexure deformation stage, so the process of the chip formation is the basis of the edge defects formation. In addition, the relationship between the nucleation and propagation direction of the crack and the variation of the edge defect shape on the workpiece was investigated by theory, and it found that the negative shear angle formation is the primary cause of the edge defect formation. A mixed mode crack is found in the crack propagation stage. The sizes of edge defects were measured by the experiment and simulation, and the edge defect size decrease with the increasing of tool rake angle, while increase with increasing cutting depth and cutting speed.

Influence of the Process Variables on the Temperature Distribution in AISI 1045 Turning

2012 ◽  
Vol 557-559 ◽  
pp. 1364-1368
Author(s):  
Yong Feng ◽  
Mu Lan Wang ◽  
Bao Sheng Wang ◽  
Jun Ming Hou
Keyword(s):  
Temperature Distribution ◽  
High Speed ◽  
Metal Cutting ◽  
Constitutive Relations ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Fe Model ◽  
Process Variables ◽  
Machined Surface ◽  
Aisi 1045

High-speed metal cutting processes can cause extremely rapid heating of the work material. Temperature on the machined surface is critical for surface integrity and the performance of a precision component. However, the temperature of a machined surface is challenging for in-situ measurement.So, the finite element(FE) method used to analyze the unique nonlinear problems during cutting process. In terms of heat-force coupled problem, the thermo-plastic FE model was proposed to predict the cutting temperature distribution using separated iterative method. Several key techniques such as material constitutive relations, tool-chip interface friction and separation and damage fracture criterion were modeled. Based on the updated Lagrange and arbitrary Lagrangian-Eulerian (ALE) method, the temperature field in high speed orthogonal cutting of carbon steel AISI-1045 were simulated. The simulated results showed good agreement with the experimental results, which validated the precision of the process simulation method. Meanwhile, the influence of the process variables such as cutting speed, cutting depth, etc. on the temperature distribution was investigated.

Simulation of Chip Formation in an Orthogonal Cutting Process Using Fem

2002 ◽  
pp. 167-177 ◽  
Author(s):  
G. Giorleo ◽  
R. Teti ◽  
A. Langella ◽  
D. D’Addona ◽  
U. Prisco
Keyword(s):  
Chip Formation ◽  
Orthogonal Cutting ◽  
Cutting Process

Effect of Minimum Quantity Lubrication to Prediction of Cutting Temperature Distribution in Turning Material AISI-1045

2020 ◽  
Vol 902 ◽  
pp. 97-102
Author(s):  
Tran Trong Quyet ◽  
Pham Tuan Nghia ◽  
Nguyen Thanh Toan ◽  
Tran Duc Trong ◽  
Luong Hong Sam ◽  
...  
Keyword(s):  
Temperature Distribution ◽  
Shear Zone ◽  
Orthogonal Cutting ◽  
Cutting Temperature ◽  
Chip Thickness ◽  
Minimum Quantity Lubrication ◽  
Minimum Quantity ◽  
The Difference ◽  
Secondary Shear Zone ◽  
Cutting Model

This paper presents a prediction of cutting temperature in turning process, using a continuous cutting model of Johnson-Cook (J-C). An method to predict the temperature distribution in orthogonal cutting is based on the constituent model of various material and the mechanics of their cutting process. In this method, the average temperature at the primary shear zone (PSZ) and the secondary shear zone (SSZ) were determined for various materials, based on a constitutive model and a chip-formation model using measurements of cutting force and chip thicknes. The J-C model constants were taken from Hopkinson pressure bar tests. Cutting conditions, cutting forces and chip thickness were used to predict shear stress. Experimental cutting heat results with the same cutting parameters using the minimum lubrication method (MQL) were recorded through the Testo-871 thermal camera. The thermal distribution results between the two methods has a difference in value, as well as distribution. From the difference, we have analyzed some of the causes, finding the effect of the minimum quantity lubrication parameters on the difference.

Cyclic shear angle for lamellar chip formation in ultra-precision machining

2020 ◽  
Vol 234 (13) ◽  
pp. 2673-2680 ◽  
Author(s):  
Shaojian Zhang ◽  
Pan Guo ◽  
Zhiwen Xiong ◽  
Suet To
Keyword(s):  
Chip Formation ◽  
Diamond Tool ◽  
Orthogonal Cutting ◽  
Rake Angle ◽  
Shear Angle ◽  
Precision Machining ◽  
Cyclic Shear ◽  
Intrinsic Mechanism ◽  
Classical Models ◽  
Ultra Precision

Shear angle is classically considered constant. In the study, a series of straight orthogonal cutting tests of ultra-precision machining revealed that shear angle cyclically evolved with each lamellar chip formation, i.e. cyclic shear angle. It grew up from an initial shear angle of 0° to a final shear angle 90°- α ( α: tool rake angle) and underwent a series of transient shear angles like classical shear angles and a critical shear angle. The critical shear angle is the sum of the half of the tool rake angle and the characteristic shear angle determined by material anisotropy without the friction effect. Moreover, a new model was developed. Further, a series of face turning tests of ultra-precision machining verified that the cyclic shear angle was the intrinsic mechanism of cyclic cutting forces and lamellar chip formation to induce twin-peak high-frequency multimode diamond-tool-tip vibration. Significantly, the study draws up an understanding of shear angle for the discrepancy among the classical models.

Sign in / Sign up

Export Citation Format

Share Document