Guided wave structural health monitoring with an array of novel piezoelectric transducers

2014 ◽  
Author(s):  
A. Lesky ◽  
C. J. Lissenden
Keyword(s):  
Structural Health Monitoring ◽  
Health Monitoring ◽  
Guided Wave ◽  
Piezoelectric Transducers ◽  
Structural Health

Selective actuation and sensing of antisymmetric ultrasonic waves using shear-deforming piezoelectric transducers

2020 ◽  
pp. 147592172094493
Author(s):  
Parry Carrison ◽  
Hussain Altammar ◽  
Nathan Salowitz
Keyword(s):  
Structural Health Monitoring ◽  
Health Monitoring ◽  
Electromechanical Coupling ◽  
Lead Zirconate ◽  
Guided Wave ◽  
Neutral Axis ◽  
Piezoelectric Transducers ◽  
Structural Health ◽  
Symmetric Wave ◽  
Wave Modes

Structural health monitoring of thin plate and beam structures using ultrasonic guided wave techniques has been widely studied and demonstrated advanced capabilities dependent on detailed analysis of specific guided wave modes. A common setup employs the d31 electromechanical coupling of piezoelectric wafer active sensors mounted on the surface of a beam or plate. Analysis of output signals from these basic systems is complicated because they represent multiple superposed ultrasonic wave modes that propagate at different velocities, are dispersive, and undergo reflection, refraction, and mode conversion. Multiple techniques have been pursued to overcome this complication. This article presents recent research into the use of shear-deforming lead zirconate titanate piezoelectric transducers, employing the d15 electromechanical coupling property, embedded within beam-like structures to selectively actuate and sense specific ultrasonic wave modes. The internally located transducers actuated and sensed transverse shear, coupled to bending and antisymmetric waves. A combination of results from finite element simulations and experiments found that d15 transducers located at the neutral axis of a beam exclusively coupled to antisymmetric wave modes and did neither directly actuate nor sense symmetric wave modes. Further study was performed to evaluate the effects of off-neutral-axis location on the mode selectivity and found that off axis location of the d15 transducer did not diminish the coupling to antisymmetric wave modes, but introduced coupling to symmetric wave modes. Additional study was performed to assess the ability of structural health monitoring systems employing shear-deforming d15 lead zirconate titanates located at the neutral axis to detect common forms of damage in laminate structures. The combination of selective actuation and selective sensing provides a powerful tool for signal analysis in ultrasonic structural health monitoring of thin plates and beams.

Validation of Impedance-Based Structural Health Monitoring in a Simulated Biomedical Implant System

2018 ◽  
Author(s):  
Robert I. Ponder ◽  
Mohsen Safaei ◽  
Steven R. Anton
Keyword(s):  
Structural Health Monitoring ◽  
Health Monitoring ◽  
Orthopedic Implants ◽  
The United States ◽  
The State ◽  
Piezoelectric Transducers ◽  
Bone Implant ◽  
Electromechanical Impedance ◽  
Structural Health ◽  
Number Of Patients

Total Knee Replacement (TKR) is an important and in-demand procedure for the aging population of the United States. In recent decades, the number of TKR procedures performed has shown an increase. This pattern is expected to continue in the coming decades. Despite medical advances in orthopedic surgery, a high number of patients, approximately 20%, are dissatisfied with their procedure outcomes. Common causes that are suggested for this dissatisfaction include loosening of the implant components as well as infection. To eliminate loosening as a cause, it is necessary to determine the state of the implant both intra- and post-operatively. Previous research has focused on passively sensing the compartmental loads between the femoral and tibial components. Common methods include using strain gauges or even piezoelectric transducers to measure force. An alternative to this is to perform real-time structural health monitoring (SHM) of the implant to determine changes in the state of the system. A commonly investigated method of SHM, referred to as the electromechanical impedance (EMI) method, involves using the coupled electromechanical properties of piezoelectric transducers to measure the host structure’s condition. The EMI method has already shown promise in aerospace and infrastructure applications, but has seen limited testing for use in the biomechanical field. This work is intended to validate the EMI method for use in detecting damage in cemented bone-implant interfaces, with TKR being used as a case study to specify certain experimental parameters. An experimental setup which represents the various material layers found in a bone-implant interface is created with various damage conditions to determine the ability for a piezoelectric sensor to detect and quantify the change in material state. The objective of this work is to provide validation as well as a foundation on which additional work in SHM of orthopedic implants and structures can be performed.

scholarly journals Research on the Progress of Interdigital Transducer (IDT) for Structural Damage Monitoring

2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Wang Ziping ◽  
Xiong Xiqiang ◽  
Qian Lei ◽  
Wang Jiatao ◽  
Fei Yue ◽  
...  
Keyword(s):  
Structural Health Monitoring ◽  
Health Monitoring ◽  
Structural Damage ◽  
Large Scale ◽  
Safety Information ◽  
Health And Safety ◽  
Guided Wave ◽  
Structural Safety ◽  
Structural Health ◽  
Damage Monitoring

In the application of Structural Health Monitoring (SHM) methods and related technologies, the transducer used for electroacoustic conversion has gradually become a key component of SHM systems because of its unique function of transmitting structural safety information. By comparing and analyzing the health and safety of large-scale structures, the related theories and methods of Structural Health Monitoring (SHM) based on ultrasonic guided waves are studied. The key technologies and research status of the interdigital guided wave transducer arrays which used for structural damage detection are introduced. The application fields of interdigital transducers are summarized. The key technical and scientific problems solved by IDT for Structural Damage Monitoring (SHM) are presented. Finally, the development of IDT technology and this research project are summarised.

Sign in / Sign up

Export Citation Format

Share Document