Rising the work uniformity of thread milling cutters in machining parts of rocket and space technology

2019 ◽  
Author(s):  
O. V. Malkov ◽  
A. C. Karelsky
1997 ◽  
Vol 161 ◽  
pp. 299-311 ◽  
Author(s):  
Jean Marie Mariotti ◽  
Alain Léger ◽  
Bertrand Mennesson ◽  
Marc Ollivier

AbstractIndirect methods of detection of exo-planets (by radial velocity, astrometry, occultations,...) have revealed recently the first cases of exo-planets, and will in the near future expand our knowledge of these systems. They will provide statistical informations on the dynamical parameters: semi-major axis, eccentricities, inclinations,... But the physical nature of these planets will remain mostly unknown. Only for the larger ones (exo-Jupiters), an estimate of the mass will be accessible. To characterize in more details Earth-like exo-planets, direct detection (i.e., direct observation of photons from the planet) is required. This is a much more challenging observational program. The exo-planets are extremely faint with respect to their star: the contrast ratio is about 10−10at visible wavelengths. Also the angular size of the apparent orbit is small, typically 0.1 second of arc. While the first point calls for observations in the infrared (where the contrast goes up to 10−7) and with a coronograph, the latter implies using an interferometer. Several space projects combining these techniques have been recently proposed. They aim at surveying a few hundreds of nearby single solar-like stars in search for Earth-like planets, and at performing a low resolution spectroscopic analysis of their infrared emission in order to reveal the presence in the atmosphere of the planet of CO H2O and O3. The latter is a good tracer of the presence of oxygen which could be, like on our Earth, released by biological activity. Although extremely ambitious, these projects could be realized using space technology either already available or in development for others missions. They could be built and launched during the first decades on the next century.


2005 ◽  
Vol 11 (3-4) ◽  
pp. 96-99
Author(s):  
V.I. Slivinsky ◽  
◽  
M.V. Slivinsky ◽  
Keyword(s):  

Author(s):  
Rupali Dhal ◽  
D. P. Satapathy

The dynamic aspects of the reservoir which are water spread, suspended sediment distribution and concentration requires regular and periodical mapping and monitoring. Sedimentation in a reservoir affects the capacity of the reservoir by affecting both life and dead storages. The life of a reservoir depends on the rate of siltation. The various aspects and behavior of the reservoir sedimentation, like the process of sedimentation in the reservoir, sources of sediments, measures to check the sediment and limitations of space technology have been discussed in this report. Multi satellite remote sensing data provide information on elevation contours in the form of water spread area. Any reduction in reservoir water spread area at a specified elevation corresponding to the date of satellite data is an indication of sediment deposition. Thus the quality of sediment load that is settled down over a period of time can be determined by evaluating the change in the aerial spread of the reservoir at various elevations. Salandi reservoir project work was completed in 1982 and the same is taken as the year of first impounding. The original gross and live storages capacities were 565 MCM& 556.50 MCM respectively. In SRS CWC (2009), they found that live storage capacity of the Salandi reservoir is 518.61 MCM witnessing a loss of 37.89 MCM (i.e. 6.81%) in a period of 27 years.The data obtained through satellite enables us to study the aspects on various scales and at different stages. This report comprises of the use of satellite to obtain data for the years 2009-2013 through remote sensing in the sedimentation study of Salandi reservoir. After analysis of the satellite data in the present study(2017), it is found that live capacity of the reservoir of the Salandi reservoir in 2017 is 524.19MCM witnessing a loss of 32.31 MCM (i.e. 5.80%)in a period of 35 years. This accounts for live capacity loss of 0.16 % per annum since 1982. The trap efficiencies of this reservoir evaluated by using Brown’s, Brune’s and Gill’s methods are 94.03%, 98.01and 99.94% respectively. Thus, the average trap efficiency of the Salandi Reservoir is obtained as 97.32%.


2020 ◽  
Vol 25 (1) ◽  
pp. 45-53
Author(s):  
L.B. Strogonova ◽  
◽  
Yu.A. Vasin ◽  
R.A. Gardunio ◽  
A.N. Knyazev ◽  
...  

Since April 1961, all manned space flights have been accompanied by medical control ensuring flight safety. Medical control in space flight has a technological and medical methodology that allows, at a distance from medical specialists, to make an adequate medical decision for the current situation. This work would be impossible if there were no measures taken to unify and standardize equipment and techniques. Telemedicine technologies developed on the basis of flight medical control. The origin of the word telemedicine comes from the expression «telemetric medical information», adopted in space technology. The issues of mutual development and mutual enrichment, standardization of methods and equipment of two areas of medicine, medical control in extreme situations and general telemedicine are considered in this article.


2018 ◽  
Vol 11 (1) ◽  
pp. 36
Author(s):  
Risdiyanto Edy Saputro ◽  
Indri Yaningsih ◽  
Heru Sukanto

Penelitian ini dilakukan untuk mengetahui pengaruh penerapan CAD /CAM terhadap proses penggilingan CNC terhadap kekasaran dan ketelitianpermukaan. Spesimen dibuat dengan menggunakan tujuh jenis prosespemotongan. Terdapat face milling, pocket milling, profile milling, slotmilling, pengeboran, thread milling dan surface contouring. Hasil penelitianmenunjukkan bahwa penerapan CAD / CAM dengan variasi prosespemotongan menghasilkan nilai kekasaran yang lebih rendah daripadatanpa penerapan CAD / CAM. Nilai kekasaran permukaan untuk masingmasingproses pemotongan adalah proses face milling (0,5028 μm; 0,5132μm), slot milling (0.664 μm; 0.6556 μm), profile milling (1.282 μm; 1.3128μm), pocket milling (1.3852 μm; 1.4856 μm ) Dan proses pengeboran(1.9944 μm; 2.1136 μm). Nilai rata-rata dimensi dari pengukuranmenunjukkan selisih antara hasil implementasi CAD / CAM dan tanpaimplementasi CAD / CAM. Persentase perbedaan panjang dan lebarmasing-masing 0,037%; 0,059% untuk profile milling; 0,039%; 0,061%untuk pocket milling; Dan 0.151%; 0,317% untuk pengeboran Penggunaanstatistik penerapan CAD / CAM tidak secara signifikan mempengaruhi nilaikekasaran permukaan namun memiliki pengaruh signifikan terhadapketepatan produk dengan tingkat presisi 95%.


Sign in / Sign up

Export Citation Format

Share Document