Steady-state characteristics of fcc pure metals processed by severe plastic deformation: experiments and modelling

Author(s):  
Fan Liu ◽  
Tao Fa ◽  
Pi Heng Chen ◽  
Jing Tao Wang
2006 ◽  
Vol 977 ◽  
Author(s):  
Xavier Sauvage ◽  
Xavier Quelennec ◽  
Peter Jessner ◽  
Florian Wetscher ◽  
Reinhard Pippan

AbstractGrain size reduction induced by severe plastic deformation (SPD) and the resulting mechanical properties have been widely investigated for pure metals but less is known and reported about multi-phase materials. To study the grain size reduction mechanisms in multiphase structure subjected to SPD, two copper based composites (Cu-10%Fe and Cu-43%Cr) were severely deformed by torsion under high pressure. The grain size achieved with these composite materials is much smaller than in pure metals. It is for example in a range of 10 to 20 nm for the Cu-43%Cr composite, e.g. one order of magnitude lower than in pure Cu processed by SPD. Three dimensional atom probe data show also the formation of non equilibrium supersaturated solid solutions. The mechanisms of the deformation induced intermixing are discussed together with its influence on the mechanical properties.


Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 601
Author(s):  
Boris B. Straumal ◽  
Roman Kulagin ◽  
Leonid Klinger ◽  
Eugen Rabkin ◽  
Petr B. Straumal ◽  
...  

During severe plastic deformation (SPD), the processes of lattice defect formation as well as their relaxation (annihilation) compete with each other. As a result, a dynamic equilibrium is established, and a steady state is reached after a certain strain value. Simultaneously, other kinetic processes act in opposite directions and also compete with each other during SPD, such as grain refinement/growth, mechanical strengthening/softening, formation/decomposition of solid solution, etc. These competing processes also lead to dynamic equilibrium and result in a steady state (saturation), albeit after different strains. Among these steady-state phenomena, particle fragmentation during the second phase of SPD has received little attention. Available data indicate that precipitate fragmentation slows down with increasing strain, though saturation is achieved at higher strains than in the case of hardness or grain size. Moreover, one can consider the SPD-driven nanocrystallization in the amorphous phase as a process that is opposite to the fragmentation of precipitates. The size of these crystalline nanoprecipitates also saturates after a certain strain. The fragmentation of precipitates during SPD is the topic of this review.


Author(s):  
Boris B. Straumal ◽  
Askar R. Kilmametov ◽  
Yulia Ivanisenko ◽  
Andrei A. Mazilkin ◽  
Olga A. Kogtenkova ◽  
...  

2004 ◽  
Vol 443-444 ◽  
pp. 243-246 ◽  
Author(s):  
A.R. Kilmametov ◽  
Igor V. Alexandrov ◽  
Anna Dubravina

In the present work the processes of crystallographic texture formation during severe plastic deformation (SPD), which has been carried out in the conditions of high imposed pressures (up to 6 GPa) and extremely large cumulative deformation degree (e up to 1÷100 and more) in pure metals, are investigated. It is shown that the processes of nanostructure formation as a result of SPD are accompanied not only by known processes such as a fragmentation, extension of misorientation angles, character modification of dislocation density, but also by the formation of deformation textures. The deformation textures, having been formed as a result of SPD are analyzed for the examples of FCC Cu, BCC W and HPC Ti, depending on a cumulative deformation degree and SPD scheme. The obtained crystallographic texture data are used for the analysis of the nanostructured state formation regularities.


Author(s):  
V V Popov ◽  
E N Popova ◽  
V P Pilyugin ◽  
D D Kuznetsov ◽  
A V Stolbovsky

Sign in / Sign up

Export Citation Format

Share Document