Influence of ignition timing on performance and emission characteristics of an SI engine fueled with equi-volume blend of methanol and gasoline

Author(s):  
Nuthan Prasad B. S. ◽  
Kumar G. N.

In this world, the population is increased and the number of vehicles increased. Not only population the pollution is increased lot by vehicles in the world harmful pollutant is realized from the vehicles like CO, HC, NOx and smoke particulates. It is inevitable to find some new technology, which increases the better performance and emission characteristics. Partially premixed compression ignition (PCCI) is the best technology for the reducing of harmful pollution in the vehicle, which uses the diesel as fuel it, gives the advantages of both CI and SI engine. This paper investigates the performance and emission characteristics of partially premixed diesel engine. Diesel engine has two injectors of port fuel injector (PFI) and direct injector (DI) to inject the fuel in different timing and electrical control unit (ECU) passes the power to PFI; it can control the injection timing and increases the fuel content from the fuel pump. The main aim in this paper is studied is effect of partially premixed ratio, performance of engine and emission characteristics of diesel engine


TheSI engine could not be operatedefficientlywith neat ethanol fuel due to its high selfignition temperature and latent heat of vaporizationcompared with petrol.The above issues of SI engine is turned to be an objective of this study, where the SI engine was operated with neat ethanol fuel under different inlet air temperatures.The result of this study is indicated that the neat ethanol fuel could be utilized efficiently in SI engine with waste heat recovery system.The specific fuel consumption (SFC) of SI engine has decreased with neat ethanol fuel compared with petrol fuelled engine. It is also found that theSI engine has registered almost same brake thermal efficiency (BTE) values with neat ethanol compared to petrol.The exhaust emissions such as carbon monoxide (CO) and Hydrocarbon (HC)were reduced in SI engine, at the same time there was an increase in oxide of nitrogen (NOx).


2013 ◽  
Vol 52 (3) ◽  
pp. 285-293 ◽  
Author(s):  
Nitesh Mittal ◽  
Robert Leslie Athony ◽  
Ravi Bansal ◽  
C. Ramesh Kumar

2015 ◽  
Author(s):  
Hassan A. Khairallah ◽  
Warren S. Vaz ◽  
Umit O. Koylu

Exhaust gas recirculation (EGR) and ignition timing have strong effects on engine performance and exhaust emissions. In the present study, detailed chemical reactions with 29 steps of hydrogen oxidation with additional nitrogen oxidation reactions were coupled with an advanced CFD code to investigate the engine performance and emission characteristics of a SI engine fueled with hydrogen. The NOx formation within the engine was computed using the extended Zeldovich mechanism with parameters adjusted for a carbon-free fuel such as hydrogen. The computational results were validated against experimental results with equivalence ratio of 0.84 and fixed ignition timing at crank angle of 5° BTDC (before top dead center). The simulations were then employed to examine the effects of EGR and ignition timing on the engine performance and NOx formation and emission. The EGR ratio was varied between 5% and 15% while the ignition timings considered were 5°, 10°, 15°, and 20° BTDC. It was found that NOx emission increased with advancing the ignition timing away from TDC while the indicated engine power showed an increasing trend with further advancing the ignition timing. Higher indicated mean effective pressure (IMEP) and indicated thermal efficiency were obtained with an advanced ignition timing of 20° BTDC. The model was also run with three different EGR ratios of 5%, 10% and 15% with fixed ignition timing at 5° BTDC. The simulation results quantified the reduction in NOx and the indicated engine power with the increase in the EGR ratio. The computations were consistent with the hypothesis that the combustion duration increases with the EGR ratio. Finally, the maximization of engine power and minimization of NOx emissions were considered as conflicting objectives. The different data points were plotted in the objective space. Using the concept of “knee”, (5° BTDC, 0% EGR) was selected as the optimal operating point representing the best trade-off between maximum engine power and minimum NOx emissions.


Sign in / Sign up

Export Citation Format

Share Document