Estimates of the air-fuel ratio at the time of ignition in a pre-chamber using a narrow throat geometry

The benefits of pre-chamber combustion (PCC), such as improved engine efficiency and reduced NOx emissions, are primarily observed when operating at lean conditions with an active pre-chamber, where auxiliary fuel is supplied directly to the pre-chamber. Estimating the pre-chamber excess air ratio (λ) is important in the active pre-chamber concept to gain insights into the pre-chamber combustion phenomenon. Experimental investigations were performed using a narrow-throat pre-chamber at global-λ 1.6, 1.8, and 2.0. The fraction of fuel energy injected in the pre-chamber over the total fuel energy was fixed at 3%, 7%, and 13% for each global-λ. The mixture formation process inside the pre-chamber is first simulated using the 1-D simulation software GT-Power to analyze the pre-chamber λ at the ignition timing. However, the 1-D results were unable to reproduce the experimental observations on the pre-chamber pressure buildup accurately. Upon simulating the same conditions using the 3-D CFD software CONVERGE, the pre-chamber λ estimated from the CFD model is well-correlated to the experimental data. The CFD results indicate that the amount of fuel trapped in the pre-chamber at the inlet valve closing timing is over-predicted by the 1-D simulations. A correlation between the injected and the trapped fuel in the pre-chamber is proposed by theoretical scavenging models and applied to the 1-D simulation results to improve pre-chamber λ prediction accuracy.

The research and analysis of Homogeneous Charge Compression Ignition Engine

HCCI represents homogeneous charge compression ignition. It is a cleaner, higher thermal efficiency, and higher fuel efficiency alternative combustion technology. This engine combines the advantages of diesel and gasoline engines so that the compression ratio of diesel engines can be achieved even when gasoline is used as fuel, and there is basically no NOx and soot emissions. However, the HCCI still has some problems such as ignition timing unstable, bad load and speed variation, and cold start capacity. Today, due to the above shortcomings, HCCI is still mainly researched and developed in the laboratory without mass production. The purpose of this paper is discussing the advantage and disadvantage of HCCI technique and analyse the operating principle to provide possible solution that will improve the quality of HCCI engine before the mass production of HCCI.

A design of fuel control unit for eco vehicle engines

Nowadays, solution of fuel injection is the best way for design of fuel economy vehicle while mechanical improvement has almost reached its limit. This article shows result of the research and making the fuel injection electronic control unit (ECU) used for two annually contests named Honda EMC and Shell ECO-marathon. The control circuit is designed and coded with Arduino Mega, sensors and actuators equipped in popular cars. The circuit also allows users to change the fuel injection map and the ignition timing map to suit ECO vehicle, its necessary data help driver to have better seeing and adjusting during contest time. This permit contestant teams to modify base on their design and showed data can help contest process become more optimized and simply.

Effect of injection and ignition timing on a hydrogen-lean stratified charge combustion engine

Hydrogen can be used as a fuel for internal combustion engines to realize a carbon-neutral transport society. By extending the lean limit of spark ignition engines, their efficiency, and emission characteristics can be improved. In this study, stratified charge combustion (SCC) using monofueled hydrogen direct injection was used to extend the lean limit of a spark ignition engine. The injection and ignition timing were varied to examine their effect on the SCC characteristics. An engine experiment was performed in a spray-guided single-cylinder research engine, and the nitrogen oxide and particulate emissions were measured. Depending on the injection timing, two different types of combustion were characterized: mild and hard combustion. The advancement and retardation of the ignition timing resulted in a high and low combustion stability, respectively. The lubricant-based particulate emission was attributed to the in-cylinder temperature and area of the flame surface. Therefore, the results of the study suggest that the optimization of the hydrogen SCC based on the injection and ignition timing could contribute to a clean and efficient transport sector.

The Development of Combustion Strategy in Improving the Performances of SI-PFI Engine Using E50 of Gasoline-Bioethanol Fuel Blend

This research aims to improve the combustion performance of gasoline-bioethanol fuel blended in the ratio of 50:50 (E50) on the spark-ignition engine by employing a new combustion strategy. The Box Behnken Design of Response Surface Methodology and Non-Linear Programming was employed to optimize the performance of the engine and create some engine parameters. The performance of the engine consists of power, torque, thermal efficiency, fuel consumption, and the emission of CO and HC, while the engine and combustion parameters are compression ratio, ignition timing, and engine speed. A new combustion strategy will be applied in this study with a tiered mapping process for each engine parameter based on the MBT. The brake torque increased by 13.5 % while HC and CO emissions decreased by 15 % and 71 % respectively when the combustion strategy applied if compared o the pure gasoline in engine standard condition. Furthermore, the BSFC increased by 33 % while BTE decreased by 15 % towards the gasoline fuel. The non-linear programming applied in this study intended to figure out the best combination of the engine parameters in obtaining optimum engine performances. In the RSM analysis, the codes --1, 0, 1 represented 12, 12.5, and 13 of compression ratio, 16, 20, and 24 BTDC of ignition timing and 2000, 5000, and 8000 rpm of engine speed. Therefore, 20 BTDC of ignition timing and 13:1 of compression ratio is the optimum engine parameters used in gaining the optimal performance of the engine when E50 runs in SI-PFI engine of 150 cm3