The influence of nanoparticles with KCl salt on improving of water-based drilling fluid properties: experimental analysis and trial field test

2020 ◽  
pp. 1-18
Author(s):  
Majid Sajjadian ◽  
Vali Ahmad Sajjadian ◽  
Alimorad Rashidi
Keyword(s):  
Field Test ◽  
Experimental Analysis ◽  
Drilling Fluid ◽  
Trial Field ◽  
Water Based ◽  
Fluid Properties

scholarly journals Wet Drilled Cuttings Bed Rheology

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1644
Author(s):  
Camilo Pedrosa ◽  
Arild Saasen ◽  
Bjørnar Lund ◽  
Jan David Ytrehus
Keyword(s):  
Drilling Fluid ◽  
Drilling Fluids ◽  
Parallel Plates ◽  
Single Particles ◽  
Cuttings Transport ◽  
Transport Studies ◽  
Water Based ◽  
Fluid Properties ◽  
External Forces ◽  
Cuttings Bed

The cuttings transport efficiency of various drilling fluids has been studied in several approaches. This is an important aspect, since hole cleaning is often a bottleneck in well construction. The studies so far have targeted the drilling fluid cuttings’ transport capability through experiments, simulations or field data. Observed differences in the efficiency due to changes in the drilling fluid properties and compositions have been reported but not always fully understood. In this study, the cuttings bed, wetted with a single drilling fluid, was evaluated. The experiments were performed with parallel plates in an Anton Paar Physica 301 rheometer. The results showed systematic differences in the internal friction behaviors between tests of beds with oil-based and beds with water-based fluids. The observations indicated that cutting beds wetted with a polymeric water-based fluid released clusters of particles when external forces overcame the bonding forces and the beds started to break up. Similarly, it was observed that an oil-based fluid wetted bed allowed particles to break free as single particles. These findings may explain the observed differences in previous cutting transport studies.

Full Scale Flow Loop Experiments of Hole Cleaning Performances of Drilling Fluids

2015 ◽  
Author(s):  
Jan David Ytrehus ◽  
Ali Taghipour ◽  
Sneha Sayindla ◽  
Bjørnar Lund ◽  
Benjamin Werner ◽  
...  
Keyword(s):  
Test Section ◽  
Drilling Fluid ◽  
Drilling Fluids ◽  
Flow Loop ◽  
Base Oil ◽  
Hole Cleaning ◽  
Cleaning Performance ◽  
Water Based ◽  
Fluid Properties ◽  
Drilling Cost

One important requirement for a drilling fluid is the ability to transport the cuttings out of the borehole. Improved hole cleaning is a key to solve several challenges in the drilling industry and will allow both longer wells and improved quality of well construction. It has been observed, however, that drilling fluids with similar properties according to the API standard can have significantly different behavior with respect to hole cleaning performance. The reasons for this are not fully understood. This paper presents results from flow loop laboratory tests without and with injected cuttings size particles using a base oil and a commercial oil based drilling fluid. The results demonstrate the importance of the rheological properties of the fluids for the hole cleaning performance. A thorough investigation of the viscoelastic properties of the fluids was performed with a Fann viscometer and a Paar-Physica rheometer, and was used to interpret the results from the flow loop experiments. Improved understanding of the fluid properties relevant to hole cleaning performance will help develop better models of wellbore hydraulics used in planning of well operations. Eventually this may lead to higher ROP with water based drilling fluids as obtained with oil based drilling fluids. This may ease cuttings handling in many operations and thereby significantly reduce the drilling cost using (normally) more environmentally friendly fluids. The experiments have been conducted as part of an industry-sponsored research project where understanding the hole cleaning performance of various oil and water based drilling fluids is the aim. The experiments have been performed under realistic conditions. The flow loop includes a 10 meter long test section with 2″ OD freely rotating drillstring inside a 4″ ID wellbore made of concrete. Sand particles were injected while circulating the drilling fluid through the test section in horizontal position.

Development of New Models to Determine the Rheological Parameters of Water-based Drilling Fluid Using Artificial Intelligence

2021 ◽  
Author(s):  
Farqad Hadi ◽  
Ali Noori ◽  
Hussein Hussein ◽  
Ameer Khudhair
Keyword(s):  
Rheological Properties ◽  
High Performance ◽  
Drilling Fluid ◽  
Gel Strength ◽  
Solid Content ◽  
Rheological Parameters ◽  
Water Based ◽  
Fluid Properties ◽  
Drilling Operations ◽  
Marsh Funnel

Abstract It is well known that drilling fluid is a key parameter for optimizing drilling operations, cleaning the hole, and managing the rig hydraulics and margins of surge and swab pressures. Although the experimental works present valid and reliable results, they are expensive and time consuming. On the other hand, continuous and regular determination of the rheological mud properties can perform its essential functions during well construction. More uncertainties in planning the drilling fluid properties meant that more challenges may be exposed during drilling operations. This study presents two predictive techniques, multiple regression analysis (MRA) and artificial neural networks (ANNs), to determine the rheological properties of water-based drilling fluid based on other simple measurable properties. While mud density (MW), marsh funnel (MF), and solid% are key input parameters in this study, the output functions or models are plastic viscosity (PV), yield point (YP), apparent viscosity (AV), and gel strength. The prediction methods were demonstrated by means of a field case in eastern Iraq, using datasets from daily drilling reports of two wells in addition to the laboratory measurements. To test the performance ability of the developed models, two error-based metrics (determination coefficient R2 and root mean square error RMSE) have been used in this study. The current results of this study support the evidence that MW, MF, and solid% are consistent indexes for the prediction of rheological properties. Both mud density and solid content have a relative-significant effect on increasing PV, YP, AV, and gel strength. However, a scattering around each fit curve is observed which proved that one rheological property alone is not sufficient to estimate other properties. The results also reveal that both MRA and ANN are conservative in estimating the fluid rheological properties, but ANN is more precise than MRA. Eight empirical mathematical models with high performance capacity have been developed in this study to determine the rheological fluid properties based on simple and quick equipment as mud balance and marsh funnel. This study presents cost-effective models to determine the rheological fluid properties for future well planning in Iraqi oil fields.

Insights into the application of new eco-friendly drilling fluid additive to improve the fluid properties in water-based drilling fluid systems

2019 ◽  
Vol 183 ◽  
pp. 106424 ◽  
Author(s):  
Abo Taleb T. Al-Hameedi ◽  
Husam H. Alkinani ◽  
Shari Dunn-Norman ◽  
Mustafa A. Al-Alwani ◽  
Abdullah F. Alshammari ◽  
...  
Keyword(s):  
Drilling Fluid ◽  
Fluid Systems ◽  
Water Based ◽  
Fluid Properties

Experimental Study of Cuttings Transport Efficiency of Water Based Drilling Fluids

2014 ◽  
Author(s):  
Jan David Ytrehus ◽  
Ali Taghipour ◽  
Bjørnar Lund ◽  
Benjamin Werner ◽  
Nils Opedal ◽  
...  
Keyword(s):  
Test Section ◽  
Drilling Fluid ◽  
Drilling Fluids ◽  
Flow Loop ◽  
Cuttings Transport ◽  
Hole Cleaning ◽  
Cleaning Performance ◽  
Water Based ◽  
Fluid Properties ◽  
Drilling Cost

One important requirement for a drilling fluid is the ability to transport the cuttings out of the borehole. Improved hole cleaning is a key to solve several challenges in the drilling industry and will allow both longer wells and improved quality of well construction. It has been observed, however, that drilling fluids with similar properties according to the API standard can have significantly different behavior with respect to hole cleaning performance. The reasons for this are not fully understood. This paper presents results from laboratory tests where water based drilling fluids with similar rheological properties according to API measurements have been tested for their hole cleaning capabilities in a full scale flow loop. Thorough investigation of the viscoelastic properties of the fluids were performed with, among other instruments, a Paar-Physica rheometer. Improved understanding of the fluid properties relevant to hole cleaning performance will help develop better models of wellbore hydraulics used in planning of well operations. Eventually this may lead to higher ROP with water based drilling fluids as obtained with oil based drilling fluids. This may ease cuttings handling in many operations and thereby significantly reduce the drilling cost using (normally) more environmentally friendly fluids. The experiments have been conducted as part of an industry-sponsored research project where understanding the hole cleaning performance of various oil and water based drilling fluids is the aim. The experiments have been performed under realistic conditions. The flow loop includes a 12 meter long test section with 2″ OD freely rotating drillstring inside a 4″ ID wellbore made of concrete. Sand particles were injected while circulating the drilling fluid through the test section in horizontal position.

The Influence of SiO2 and TiO2 Nanoparticles on the Properties of Water-Based Mud

2017 ◽  
Author(s):  
Petar Mijić ◽  
Nediljka Gaurina-Međimurec ◽  
Borivoje Pašić
Keyword(s):  
Filter Cake ◽  
Drilling Fluid ◽  
Wellbore Stability ◽  
Drilling Fluids ◽  
Drilling Mud ◽  
Shale Formations ◽  
Wellbore Instability ◽  
Water Based ◽  
Fluid Properties

About 75% of all formations drilled worldwide are shale formations and 90% of all wellbore instability problems occur in shale formations. This increases the overall cost of drilling. Therefore, drilling through shale formations, which have nanosized pores with nanodarcy permeability still need better solutions since the additives used in the conventional drilling fluids are too large to plug them. One of the solutions to drilling problems can be adjusting drilling fluid properties by adding nanoparticles. Drilling mud with nanoparticles can physically plug nanosized pores in shale formations and thus reduce the shale permeability, which results in reducing the pressure transmission and improving wellbore stability. Furthermore, the drilling fluid with nanoparticles, creates a very thin, low permeability filter cake resulting in the reduction of the filtrate penetration into the shale. This thin filter cake implies high potential for reducing the differential pressure sticking. In addition, borehole problems such as too high drag and torque can be reduced by adding nanoparticles to drilling fluids. This paper presents the results of laboratory examination of the influence of commercially available nanoparticles of SiO2 (dry SiO2 and water-based dispersion of 30 wt% of silica), and TiO2 (water-based dispersion of 40 wt% of titania) in concentrations of 0.5 wt% and 1 wt% on the properties of water-based fluids. Special emphasis is put on the determination of lubricating properties of the water-based drilling fluids. Nanoparticles added to the base mud without any lubricant do not improve its lubricity performance, regardless of their concentrations and type. However, by adding 0.5 wt% SiO2-disp to the base mud with lubricant, its lubricity coefficient is reduced by 4.6%, and by adding 1 wt% TiO2-disp to the base mud with lubricant, its lubricity coefficient is reduced by 14.3%.

scholarly journals Experimental investigation of the effect of TiO2 nanofluid and KCl salt on polymeric water-based drilling fluid properties

2019 ◽  
Vol 74 ◽  
pp. 9 ◽  
Author(s):  
AmirHossein Parizad ◽  
Ali Khorram Ghahfarokhi ◽  
Khalil Shahbazi ◽  
Amin Daryasafar ◽  
Tofigh Sayahi ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Base Fluid ◽  
Drilling Fluid ◽  
Rheological Parameters ◽  
Rheological Models ◽  
Shear Rates ◽  
Water Based ◽  
Fluid Properties ◽  
Different Temperatures ◽  
The Stability

In petroleum industries, nanofluids have the potential to improve the characteristics of the fluids used in drilling wells or Enhanced Oil Recovery (EOR) processes. In this study, a water based mud containing polymer was considered as the base fluid. Different concentrations of TiO2 nanoparticle (0, 0.5 and 0.75 wt%) and different concentrations of KCl salt (0, 0.5, 1.5, and 3 wt%) were added to the base fluid and exposed to different temperatures (30, 50, 70 and 90 °C) with 19 different shear rates for investigating the effects of nanoparticle concentration, salt concentration, temperature and shear rate on viscosity of the base mud. Presence of TiO2 particles enhanced not only the rheological behavior but also electrical and thermal conductivity of fluid up to 25% and 43%, respectively. Furthermore, the stability of the fluid containing salt and nanoparticle was investigated in these temperatures owing to the fact that the temperature could cause degradation of the fluid. For the purpose of investigating this phenomenon, the after cooling experiment was conducted. In addition, the data gathered in this investigation were examined by using three famous rheological models (Power law, Herschel-Bulkley and Herschel-Bulkley-Papanastasiou models) and the rheological parameters of each model were determined.

Designing Drilling Fluids to Combat Circulation Losses for Arctic Environments

2015 ◽  
Author(s):  
Mesfin Belayneh ◽  
Bernt S. Aadnøy
Keyword(s):  
Low Temperature ◽  
Laboratory Experiments ◽  
Drilling Fluid ◽  
Drilling Fluids ◽  
Drilling Mud ◽  
Drilling Operation ◽  
Water Based ◽  
Fluid Properties ◽  
Fracture Sealing ◽  
Productive Time

Drilling fluid plays a key role in an efficient drilling operation to minimize problems such as wellbore collapse, circulation losses and stuck pipe. Well instability problems are costly as they increase the non-productive time and the overall budget (1) (2). Well instability problems controlled by designing appropriate mud density and fluid properties that controls the well. The fracture sealing ability of a drilling fluid is one very important of the drilling mud. This paper presents design of water-based drilling fluids and results from laboratory experiments to quantify the loss circulation performance of drilling fluids. Because it is preferable to use oil-based muds in some well sections, the paper will also include a recent study on how to minimize losses when using oil based muds. Here uses of micro/nanoparticles have shown to reduce filtrate losses and to build barriers that are more efficient during circulation loss events. All the tests presented are at low temperature, which is suitable for Artic environments.

Sign in / Sign up

Export Citation Format

Share Document