scholarly journals System-Scale Modeling of a Building-Integrated, Transparent Concentrating Photovoltaic and Thermal Collector

2021 ◽  
Vol 2069 (1) ◽  
pp. 012117
Author(s):  
N E Novelli ◽  
J Shultz ◽  
M Aly Etman ◽  
K Phillips ◽  
M M Derby ◽  
...  
Keyword(s):  
Thermal Energy ◽  
Heat Engine ◽  
Building Design ◽  
Building Envelope ◽  
Commercial Building ◽  
Human Scale ◽  
Sustainable Operation ◽  
Net Zero ◽  
Operating Temperatures ◽  
Cooling Loads

Abstract The buildings sector is a principal contributor to global greenhouse gas emissions, but consistently falls short of targets for harnessing on-site energy resources towards sustainable operation. Emerging integrated solar technologies could transform buildings and urban settings into resilient, self-sufficient, and healthy environments. But if effects of these technologies are not understood in the multiple contexts in which they operate (human-scale, building-scale, district-scale), their potential is difficult to project. To explore building-scale metabolization of solar energy, a previously-developed analytical model of a Building Envelope-Integrated, Transparent, Concentrating Photovoltaic and Thermal collector (BITCoPT) was run to project electrical and thermal energy and exergy production (cogeneration) in a range of orientations and operating temperatures. Simulated annual cogeneration efficiency was noted at 27% (exergy) at an operating temperature of 55°C, and up to 55% (energy) at 25°C. Exergetic efficiency remained nearly constant as operating temperatures increased through 75°C, indicating the thermal energy collected would be some heat-engine-based applications. Although the scope of this study excludes broader architectural benefits of daylighting (lighting load reduction), and reduction of solar gains (cooling loads), these results suggest BITCoPT merits further investigation for on-site net-zero and energy-positive commercial building design, and might contribute to expanding net-zero and energy-positive architecture opportunities.

Analysis of Building Envelope Performance Effects of an Insulating Semi-Transparent Photovoltaic (STPV) Glazing Unit

2014 ◽  
Author(s):  
Dirk V. P. McLaughlin ◽  
Konstantinos Kapsis ◽  
Andreas K. Athienitis ◽  
Sam Siassi ◽  
Livio Nichilo
Keyword(s):  
Performance Standards ◽  
Energy Performance ◽  
Building Envelope ◽  
Commercial Building ◽  
Heating And Cooling ◽  
Performance Effects ◽  
Gas Consumption ◽  
U Value ◽  
And Performance ◽  
Cooling Loads

This paper presents characterization results for the electrical and thermal properties of a unique insulating semi-transparent photovoltaic (STPV) glazing unit using calorimetry hot box methods finding a U-value of 1.09 W/m2·°C and a SHGC of 0.11. These properties are then applied to an energy model of a case study commercial building in a continental climate region to examine the effects of utilizing STPV in the building envelope on the electricity and natural gas consumption levels and peak demands. The results indicate that such a building envelope can significantly reduce heating and cooling loads compared to standard glazing which would help architects maintain the desirable properties of highly glazed façades while avoiding the drop in building energy performance that could make adhering to increasingly stringent building codes and performance standards difficult. The paper also presents simulation results for the photovoltaic energy generation of the vertical STPV façades at two building orientations.

Modeling the Thermal Effects of Artificial Turf on the Urban Environment

2010 ◽  
Vol 49 (3) ◽  
pp. 332-345 ◽  
Author(s):  
Neda Yaghoobian ◽  
Jan Kleissl ◽  
E. Scott Krayenhoff
Keyword(s):  
Water Conservation ◽  
Common Ground ◽  
Building Design ◽  
Building Envelope ◽  
Shortwave Radiation ◽  
Temperate Climate ◽  
Cool Temperature ◽  
Artificial Turf ◽  
Building Walls ◽  
Cooling Loads

Abstract The effects of artificial turf (AT) on the urban canopy layer energy balance, air and surface temperatures, and building cooling loads are compared to those of other common ground surface materials (asphalt, concrete, and grass) through heat transfer modeling of radiation, convection, and conduction. The authors apply the Temperatures of Urban Facets in 3D (TUF3D) model—modified to account for latent heat fluxes—to a clear summer day at a latitude of 33° over a typical coastal suburban area in Southern California. The low albedo of artificial turf relative to the other materials under investigation results in a reduction in shortwave radiation incident on nearby building walls and an approximately equal increase in longwave radiation. Consequently, building walls remain at a relatively cool temperature that is similar to those that are adjacent to irrigated grass surfaces. Using a simple offline convection model, replacing grass ground cover with artificial turf was found to add 2.3 kW h m−2 day−1 of heat to the atmosphere, which could result in urban air temperature increases of up to 4°C. Local effects of AT on building design cooling loads were estimated. The increased canopy air temperatures with AT increase heat conduction through the building envelope and ventilation in comparison with a building near irrigated grass. However, in this temperate climate these loads are small relative to the reduction in radiative cooling load through windows. Consequently, overall building design cooling loads near AT decrease by 15%–20%. In addition, the irrigation water conservation with AT causes an embodied energy savings of 10 W h m−2 day−1. Locally, this study points to a win–win situation for AT use for urban landscaping as it results in water and energy conservation.

PSACONN mining algorithm for multi-factor thermal energy-efficient public building design

2021 ◽  
Vol 34 ◽  
pp. 102020
Author(s):  
Salih Himmetoğlu ◽  
Yılmaz Delice ◽  
Emel Kızılkaya Aydoğan
Keyword(s):  
Thermal Energy ◽  
Energy Efficient ◽  
Building Design ◽  
Public Building ◽  
Mining Algorithm

Heusler alloy-based heat engine using pyroelectric conversion for small-scale thermal energy harvesting

2021 ◽  
Vol 288 ◽  
pp. 116617
Author(s):  
Mickaël Lallart ◽  
Linjuan Yan ◽  
Hiroyuki Miki ◽  
Gaël Sebald ◽  
Gildas Diguet ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Thermal Energy ◽  
Heusler Alloy ◽  
Heat Engine ◽  
Small Scale ◽  
Thermal Energy Harvesting

scholarly journals Comparison of Factorial and Latin Hypercube Sampling Designs for Meta-Models of Building Heating and Cooling Loads

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 512
Author(s):  
Younhee Choi ◽  
Doosam Song ◽  
Sungmin Yoon ◽  
Junemo Koo
Keyword(s):  
Latin Hypercube Sampling ◽  
Building Design ◽  
Gain Coefficient ◽  
Design Parameters ◽  
Latin Hypercube ◽  
Heating And Cooling ◽  
Factor Design ◽  
Heating Loads ◽  
Cooling Loads ◽  
Interest In Research

Interest in research analyzing and predicting energy loads and consumption in the early stages of building design using meta-models has constantly increased in recent years. Generally, it requires many simulated or measured results to build meta-models, which significantly affects their accuracy. In this study, Latin Hypercube Sampling (LHS) is proposed as an alternative to Fractional Factor Design (FFD), since it can improve the accuracy while including the nonlinear effect of design parameters with a smaller size of data. Building energy loads of an office floor with ten design parameters were selected as the meta-models’ objectives, and were developed using the two sampling methods. The accuracy of predicting the heating/cooling loads of the meta-models for alternative floor designs was compared. For the considered ranges of design parameters, window insulation (WDI) and Solar Heat Gain Coefficient (SHGC) were found to have nonlinear characteristics on cooling and heating loads. LHS showed better prediction accuracy compared to FFD, since LHS considers the nonlinear impacts for a given number of treatments. It is always a good idea to use LHS over FFD for a given number of treatments, since the existence of nonlinearity in the relation is not pre-existing information.

Cost Optimization of Net-Zero Energy House

2007 ◽  
Author(s):  
George A. Mertz ◽  
Gregory S. Raffio ◽  
Kelly Kissock
Keyword(s):  
Energy Use ◽  
Cost Optimization ◽  
Building Design ◽  
Building Energy ◽  
Zero Energy ◽  
Resource Limitations ◽  
Net Zero Energy ◽  
Net Zero ◽  
Building Energy Use ◽  
The Cost

Environmental and resource limitations provide increased motivation for design of net-zero energy or net-zero CO2 buildings. The optimum building design will have the lowest lifecycle cost. This paper describes a method of performing and comparing lifecycle costs for standard, CO2-neutral and net-zero energy buildings. Costs of source energy are calculated based on the cost of photovoltaic systems, tradable renewable certificates, CO2 credits and conventional energy. Building energy simulation is used to determine building energy use. A case study is conducted on a proposed net-zero energy house. The paper identifies the least-cost net-zero energy house, the least-cost CO2 neutral house, and the overall least-cost house. The methodology can be generalized to different climates and buildings. The method and results may be of interest to builders, developers, city planners, or organizations managing multiple buildings.

scholarly journals Net Zero-Energy Home Design Strategies Learned From Canadian Experience

2008 ◽  
Vol 33 (3) ◽  
pp. 88-95
Author(s):  
Masa Noguchi
Keyword(s):  
Building Envelope ◽  
Design Strategies ◽  
Zero Energy ◽  
Sustainable Housing ◽  
Energy Technologies ◽  
Canadian Experience ◽  
Net Zero Energy ◽  
Net Zero ◽  
Micro Power ◽  
Healthy Housing

In response to the growing demand for zero-energy housing, today's home needs not only to be energy-efficient, but also to provide part of its own energy requirements. The energy efficiency may be improved by applying high thermal performance building envelope and passive energy and environmental systems to housing. Micro-power can be generated through the use of renewable energy technologies. This paper is aimed at providing a comprehensive guideline on the design techniques and approaches to the delivery of net zero-energy healthy housing in view of the ÉcoTerra house, which won the Canadian federal government's EQuilibrium sustainable housing competition. The house was built in Eastman in the province of Quebec and it is currently open to the general public in order to sharpen the consumers' awareness of commercially available net zero-energy healthy housing today.

scholarly journals The Impact of Aspect Ratio on External Heat Gain of Multi-storey Office Buildings in Jakarta

2018 ◽  
Vol 16 (1) ◽  
pp. 24-31
Author(s):  
Wasiska Iyati ◽  
◽  
Eryani Nurma Yulita ◽  
Jusuf Thojib ◽  
Heru Sufianto ◽  
...  
Keyword(s):  
Aspect Ratio ◽  
Building Design ◽  
Climatic Conditions ◽  
Building Envelope ◽  
External Heat ◽  
Office Buildings ◽  
Office Building ◽  
Cooling Load ◽  
Heat Gain ◽  
The Impact

The narrow land in big cities such as Jakarta, increases the amount of high rise building, especially multi-storey office building. Office building consumes much energy to provide air conditioning to meet the thermal comfort inside the building. On the other hand, the building shape, building envelope, and building orientation to the sun's position are the main factors in building design aspects that affect the amount of cooling load. This study aims to investigate the impact of the aspect ratio or the ratio of the longer dimension of an oblong plan to the shorter, on external heat gain of multi-storey office building. Variables examined include the transparent and solid area of building envelope, the total area of the surface of the building envelope in any orientation, and the volume of the building, as well as the influence of those proportion on the external heat gain. This study uses mathematical calculations to predict the cooling load of the building, particularly external heat gain through the walls, roof and glass, as well as comparative analysis of models studied. The study also aims to generate the design criteria of building form and proportion of multi-storey office buildings envelope with lower external heat gain. In Jakarta climatic conditions, the result on rectangular building plan with aspect ratio of 1 to 4 shows that the external heat gain did not differ significantly, and the smallest heat gain is found on the aspect ratio of 1.8. Results also showed that the greater aspect ratio, the greater reduction of external heat gain obtained by changing the orientation of the longest side facing east-west into the north-south, about 2.79% up to 42.14% on the aspect ratio of 1.1 to 4. In addition, it is known that in same building volume, changing the number of floors from 10 to 50 can improve the external heat gain almost twice.

Sign in / Sign up

Export Citation Format

Share Document