scholarly journals Calculation and analysis of landing double rocker arms holding pole based on finite element simulation

2021 ◽  
Vol 2083 (3) ◽  
pp. 032017
Author(s):  
Xing Zhang ◽  
Yingpeng Shao ◽  
Yu Xing
Keyword(s):  
Finite Element ◽  
Working Conditions ◽  
Engineering Application ◽  
Element Model ◽  
The Finite Element Method ◽  
Safety Hazards ◽  
Element Simulation ◽  
Potential Safety ◽  
The Finite Element Model ◽  
Load Conditions

Abstract Landing double rocker arms holding pole are widely used in the erection of UHV construction towers. Most of the construction arms are based on experience in engineering application, and there are some potential safety hazards. In this paper, the finite element model is established based on the relevant parameters of 700×700mm2 double rocker arm holding pole, and the actual lifting conditions of the pole are analysed. The finite element method is used to simulate nine working conditions for stress analysis. The results show that the double rocker arm holding pole has good mechanical properties under rated load conditions, which verifies the reliability of the arm design. Asymmetric moment hoisting is an important factor threatening the safety of holding pole, which must be strictly controlled.

Structural Optimization of Multi-Shaft Transmission Box

2014 ◽  
Vol 543-547 ◽  
pp. 245-248
Author(s):  
Chun Tong ◽  
Hua Li ◽  
Jin Yao ◽  
Yi Zhao
Keyword(s):  
Finite Element ◽  
Working Conditions ◽  
Load Capacity ◽  
Element Model ◽  
The Finite Element Method ◽  
Theoretical Significance ◽  
Deformation Distribution ◽  
Stress And Deformation ◽  
The Finite Element Model ◽  
Ansys Workbench

Considering the weight and loading conditions of the multi-shaft transmission box, build the finite element model and mathematical model for the box using the finite element method. According to ANSYS WORKBENCH, calculate the boxs load capacity and stress and deformation distribution under 9 working conditions then evaluate its strength and rigidity. Optimize the structure of the box to reduce its weight. The results show that the optimized box meets the strength requirements. After optimization, the multi-shaft transmission box weights 176.578 kilograms, reduced by 30.26 percentages. It improves the stress and deformation distribution and makes the structure more reasonable. It also provides important theoretical significance and engineering practical value.

Redrawing Operation a Star Shape from Cylindrical Shape Using Experimental and FE Analysis

2020 ◽  
Vol 38 (1A) ◽  
pp. 25-32
Author(s):  
Waleed Kh. Jawad ◽  
Ali T. Ikal
Keyword(s):  
Finite Element ◽  
Effective Strain ◽  
Element Model ◽  
Cylindrical Shape ◽  
Element Analysis ◽  
Punch Force ◽  
Maximum Value ◽  
Element Simulation ◽  
Blank Sheet ◽  
The Finite Element Model

The aim of this paper is to design and fabricate a star die and a cylindrical die to produce a star shape by redrawing the cylindrical shape and comparing it to the conventional method of producing a star cup drawn from the circular blank sheet using experimental (EXP) and finite element simulation (FES). The redrawing and drawing process was done to produce a star cup with the dimension of (41.5 × 34.69mm), and (30 mm). The finite element model is performed via mechanical APDL ANSYS18.0 to modulate the redrawing and drawing operation. The results of finite element analysis were compared with the experimental results and it is found that the maximum punch force (39.12KN) recorded with the production of a star shape drawn from the circular blank sheet when comparing the punch force (32.33 KN) recorded when redrawing the cylindrical shape into a star shape. This is due to the exposure of the cup produced drawn from the blank to the highest tensile stress. The highest value of the effective stress (709MPa) and effective strain (0.751) recorded with the star shape drawn from a circular blank sheet. The maximum value of lamination (8.707%) is recorded at the cup curling (the concave area) with the first method compared to the maximum value of lamination (5.822%) recorded at the cup curling (the concave area) with the second method because of this exposure to the highest concentration of stresses. The best distribution of thickness, strains, and stresses when producing a star shape by

Analysis of Hydroelectric Unit’s Upper Bracket Based on Test and FEM

2014 ◽  
Vol 721 ◽  
pp. 131-134
Author(s):  
Mi Mi Xia ◽  
Yong Gang Li
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Element Model ◽  
The Finite Element Method ◽  
Ansys Software ◽  
Element Analysis ◽  
Hydroelectric Unit ◽  
The Finite Element Analysis ◽  
Strain Rosette ◽  
The Finite Element Model

To research the load upper bracket of Francis hydroelectric unit, then established the finite-element model, and analyzed the structure stress of 7 operating condition points with the ANSYS software. By the strain rosette test, acquired the data of stress-strain in the area of stress concentration of the upper bracket. The inaccuracy was considered below 5% by analyzing the contradistinction between the finite-element analysis and the test, and match the engineering precision and the test was reliable. The finite-element method could be used to judge the stress of the upper bracket, and it could provide reference for the Structural optimization and improvement too.

Finite Element Simulation Analysis on Space KX-Joint

2014 ◽  
Vol 915-916 ◽  
pp. 146-149
Author(s):  
Yong Sheng Wang ◽  
Li Hua Wu
Keyword(s):  
Finite Element ◽  
Bearing Capacity ◽  
Simulation Analysis ◽  
Local Buckling ◽  
Element Model ◽  
Ansys Software ◽  
Element Simulation ◽  
Calculation Results ◽  
Buckling Failure ◽  
The Finite Element Model

The finite element model of the space KX-Joint was established using ANSYS software, and the failure mode and ultimate bearing capacity of KX-joint were researched. Calculation results show that the surface of chord wall on the roots of compression web members was into the plastic in K plane, and the holding pole without the plastic area and the local buckling failure happened in the surface of chord wall on the roots of Compression Web Members in X plane; The bearing capacity of the joint increased with the Chord diameter, which was appears in the form of power function.

scholarly journals COMPARISON OF SAW BLADE NATURAL FREQUENCIES AND CRITICAL SPEEDS USING CSAW AND FINITE ELEMENT ANALYSIS

2011 ◽  
Author(s):  
J. Poirier ◽  
P. Radziszewski
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Natural Frequencies ◽  
Element Model ◽  
The Finite Element Method ◽  
Element Analysis ◽  
Saw Blade ◽  
Circular Saws ◽  
The Finite Element Model ◽  
Element Method

The natural frequencies of circular saws limit the operating speeds of the saws. Current industry methods of increasing natural frequency include pretensioning, where plastic deformation is induced into the saw. To better model the saw, the finite element model is compared to current software for steel saws; C-SAW, a software program that calculates frequencies for stiffened circular saws. Using C-SAW and the finite element method the results are compared and the finite element method is validated for steel saws.

Analysis of the Temperature Field of the Diamond Wheel Dressed Using Laser Assisted Ultrasonic-Vibration Combined Dressing Method

2016 ◽  
Vol 874 ◽  
pp. 261-267 ◽  
Author(s):  
Zhi Bo Yang ◽  
Zhen Zhang ◽  
Rui Yun Yang ◽  
Ai Ju Liu
Keyword(s):  
Finite Element ◽  
Temperature Field ◽  
Finite Element Model ◽  
Ultrasonic Vibration ◽  
Working Conditions ◽  
Element Model ◽  
Diamond Wheel ◽  
Dressing Method ◽  
Infrared Temperature Measurement ◽  
The Finite Element Model

During the dressing process of diamond wheel using laser/ultrasonic-vibration combined dressing method, the removal mode of the local materials on the surface of wheel with the use of laser’s heating effect transits from brittle fracture to plastic flow, so that the wear of diamond dresser can be reduced and the dressing efficiency and surface dressing quality can be improved. Using ANSYS analysis software, the three-dimensional units were used and the nonlinearity of the material’s thermophysical properties was taken into account, and thereby, the finite element model of the temperature field of the diamond wheel heated by the laser during the dressing process was constructed. Then, the distributions of the temperature field on the surface and section of the wheel under different technological parameter were acquired. Moreover, the temperature distribution of the dressed wheel under actual working conditions was measured using infrared temperature measurement method. The results indicate that, under the same working conditions, the simulation results using finite element model fit well with the measured values, i.e., the finite element model has important guiding significance to the selection of technological parameters in dressing.

scholarly journals Finite Element Analysis of Thermoelastic Instability With Intermittent Contact

1999 ◽  
Vol 122 (1) ◽  
pp. 42-46 ◽  
Author(s):  
Hubert J. M. Geijselaers ◽  
Annette J. E. Koning
Keyword(s):  
Finite Element ◽  
Element Model ◽  
The Finite Element Method ◽  
Dimensional Model ◽  
Governing Equations ◽  
Amplitude Function ◽  
Element Analysis ◽  
Thermoelastic Instability ◽  
Intermittent Contact ◽  
The Finite Element Model

The equations that describe the development of corrugations on block braked wheel treads caused by thermoelastic instability are discretized using the finite element method. The perturbations of temperatures and distortions are described by an amplitude function, which is spatially fixed multiplied by a sinusoidal running wave term of fixed wavelength. The governing equations are such that the wave term cancels out. Only the amplitude functions are discretized in the finite element model. The intermittent nature of the contact is directly specified through the boundary conditions. Results are obtained for a simplified two-dimensional model of a train wheel. These results agree with analytical results. [S0742-4787(00)00701-3]

Finite Element Research on Damping of Viscoelastic Free Layer Damping Sheet

2014 ◽  
Vol 472 ◽  
pp. 56-61
Author(s):  
Yuan Chao He ◽  
Wen Lin Chen ◽  
Shi Wei Sun ◽  
Li Na Hao
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Loss Factor ◽  
Element Model ◽  
The Finite Element Method ◽  
Free Layer ◽  
Modal Strain Energy ◽  
Modal Strain Energy Method ◽  
The Finite Element Model ◽  
Element Method

Based on modal strain energy method, the paper discusses viscoelastic free layer damping sheet, establishes the finite element model of it and obtains the natural frequencies and loss factor. Then the paper calculates the loss factor of viscoelastic free layer damping structure with engineering empirical formula, and compares the result with that obtained by finite element method. By comparing the two results, it indicates that the finite element method is effective in analyzing this kind of problems.

The Thermal Effect in Wheel and Rail during the Brake of Port Crane

2012 ◽  
Vol 487 ◽  
pp. 879-883
Author(s):  
Jiang Wei Wu
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Finite Element Model ◽  
Thermal Effect ◽  
Thermal Effects ◽  
Element Model ◽  
The Finite Element Method ◽  
Finite Element Software ◽  
Frictional Coefficients ◽  
The Finite Element Model

With the port crane getting bigger and heavier, and also moving much faster than before, the thermal effect in wheel and rail during the brake process can be a reason of the failure of port crane. In this paper, the thermal effect during the brake process of port crane is studied using the finite element method. Based on the finite element model, the ANSYS10.0 finite element software is used. The thermal effects under different coefficients are discussed. Three different slide speed of wheel, two different loads of crane, and three different frictional coefficients are applied. The importance of the different coefficients is obtained from the numerical results.

The Application of Multi-Wedge Cross Wedge Rolling Forming Long Shaft Technology

2011 ◽  
Vol 101-102 ◽  
pp. 1002-1005 ◽  
Author(s):  
Jing Zhao ◽  
Li Qun Lu
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Finite Element Model ◽  
Rolling Mill ◽  
Three Dimensional ◽  
Element Model ◽  
Solid Model ◽  
The Finite Element Method ◽  
Cross Wedge Rolling ◽  
The Finite Element Model

The process of multi-wedge cross wedge rolling is an advanced precision technology for forming long shaft parts such as automobile semi-axes. Three-dimensional solid model and the finite element model of semi-axes on automobile and dies of its cross wedge rolling were established. The process of cross wedge rolling was simulated according to the actual dimension of semi-axes on automobile utilizing the finite element method (FEM)software ANSYS/LS-DYNA. The required force parameters for designing semi-axes mill are determined. The appropriate roller width was determined according to the length and diameter of semi-axes on automobile. The results have provided the basis for the design of specific structure of automobile semi-axes cross wedge rolling mill.

Sign in / Sign up

Export Citation Format

Share Document