scholarly journals Temperature distribution in a subduction zone

2021 ◽  
Vol 2119 (1) ◽  
pp. 012004
Author(s):  
A G Kirdyashkin ◽  
A A Kirdyashkin ◽  
Yu M Nepogodina
Keyword(s):  
Heat Transfer ◽  
Subduction Zone ◽  
Temperature Profiles ◽  
Temperature Level ◽  
Mantle Transition Zone ◽  
Crustal Layer ◽  
Hydrodynamic Structure ◽  
Subducting Plate ◽  
Field Formation ◽  
Zone Temperature

Abstract A model of the thermal and hydrodynamic structure of the subduction zone is proposed. This model includes free convection flows in the asthenospheric layer and layer C (mantle transition zone). Temperature profiles in the subducting lithospheric plate, as well as in the continental limb of the subduction zone, are presented. The heat flux due to friction at the contact between the subducting plate and the continental limb significantly affects the heat transfer and, consequently, the temperature field formation in the subduction zone. The temperature level in the crustal layer of the submerging plate implies that there is no melting in the crustal layer.

scholarly journals ON HEAT SOURCE IN SUBDUCTION ZONE

2021 ◽  
Vol 12 (3) ◽  
pp. 471-484
Author(s):  
A. A. Kirdyashkin ◽  
A. G. Kirdyashkin ◽  
V. E. Distanov ◽  
I. N. Gladkov
Keyword(s):  
Heat Source ◽  
Subduction Zone ◽  
Flow Structure ◽  
Oceanic Lithosphere ◽  
Local Heat ◽  
Melting Rate ◽  
Crustal Layer ◽  
Study Results ◽  
Subducting Plate ◽  
Thermochemical Plume

The subduction of an oceanic plate is studied as the motion of a high-viscosity Newtonian fluid. The subducting plate spreads along the 670-km depth boundary under the influence of oppositely directed horizontal forces. These forces are due to oppositely directed horizontal temperature gradients. We consider the flow structure and heat transfer in the layer that includes both the oceanic lithosphere and the crust and moves underneath a continent. The heat flow is estimated at the contact between the subducting plate and the surrounding mantle in the continental limb of the subduction zone. Our study results show that the crustal layer of the subducting plate can melt and a thermochemical plume can form at the 670-km boundary. Our model of a thermochemical plume in the subduction zone shows the following: (1) formation of a plume conduit in the crustal layer of the subducting plate; (2) formation of a primary magmatic chamber in the area wherein the melting rate equals the rate of subduction; (3) origination of a vertical plume conduit from the primary chamber melting through the continent; (4) plume eruption through the crustal layer to the surface, i.e. formation of a volcano. Our experiments are aimed to model the plume conduit melting in an inclined flat layer above a local heat source. The melt flow structure in the plume conduit is described. Laboratory modeling have revealed that the mechanisms of melt eruption from the plume conduit differ depending on whether a gas cushion is present or absent at the plume roof.

Tire Bead Overheating in Urban Buses and Trucks Using Drum Brake Systems

1998 ◽  
Vol 26 (1) ◽  
pp. 51-62
Author(s):  
A. L. A. Costa ◽  
M. Natalini ◽  
M. F. Inglese ◽  
O. A. M. Xavier
Keyword(s):  
Heat Transfer ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Thermal Energy ◽  
Structural Integrity ◽  
Experimental Temperature ◽  
Temperature Profiles ◽  
Element Analysis ◽  
Drum Brake ◽  
Fea Model

Abstract Because the structural integrity of brake systems and tires can be related to the temperature, this work proposes a transient heat transfer finite element analysis (FEA) model to study the overheating in drum brake systems used in trucks and urban buses. To understand the mechanics of overheating, some constructive variants have been modeled regarding the assemblage: brake, rims, and tires. The model simultaneously studies the thermal energy generated by brakes and tires and how the heat is transferred and dissipated by conduction, convection, and radiation. The simulated FEA data and the experimental temperature profiles measured with thermocouples have been compared giving good correlation.

AN EXPERIMENTAL AND NUMERICAL STUDY OF HEAT TRANSFER IN A SIMULATED COLLECTOR FOR A SOLAR DRYER

1993 ◽  
Vol 17 (2) ◽  
pp. 145-160
Author(s):  
P.H. Oosthuizen ◽  
A. Sheriff
Keyword(s):  
Heat Transfer ◽  
Numerical Study ◽  
Local Heat Transfer ◽  
Lower Surface ◽  
Local Heat ◽  
Electrical Heating ◽  
Temperature Profiles ◽  
Measured Temperature ◽  
Transfer Rates ◽  
Thermocouple Probe

Indirect passive solar crop dryers have the potential to considerably reduce the losses that presently occur during drying of some crops in many parts of the “developing” world. The performance so far achieved with such dryers has, however, not proved to be very satisfactory. If this performance is to be improved it is necessary to have an accurate computer model of such dryers to assist in their design. An important element is any dryer model is an accurate equation for the convective heat transfer in the collector. To assist in the development of such an equation, an experimental and numerical study of the collector heat transfer has been undertaken. In the experimental study, the collector was simulated by a 1m long by 1m wide channel with a gap of 4 cm between the upper and lower surfaces. The lower surface of the channel consisted of an aluminium plate with an electrical heating element, simulating the solar heating, bonded to its lower surface. Air was blown through this channel at a measured rate and the temperature profiles at various points along the channel were measured using a shielded thermocouple probe. Local heat transfer rates were then determined from these measured temperature profiles. In the numerical study, the parabolic forms of the governing equations were solved by a forward-marching finite difference procedure.

Natural Convection From Protruding Heat Sources in a Channel

2003 ◽  
Author(s):  
Tunc Icoz ◽  
Qinghua Wang ◽  
Yogesh Jaluria
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Natural Convection ◽  
Rayleigh Scattering ◽  
Convection Heat Transfer ◽  
Separation Distance ◽  
Natural Convection Heat Transfer ◽  
Temperature Profiles ◽  
Heat Sources ◽  
Convection Heat

Natural convection has important implications in many applications like cooling of electronic equipment due to its low cost and easy maintenance. In the present study, two-dimensional natural convection heat transfer to air from multiple identical protruding heat sources, which simulate electronic components, located in a horizontal channel has been studied numerically. The fluid flow and temperature profiles, above the heating elements placed between an adiabatic lower plate and an isothermal upper plate, are obtained using numerical simulation. The effects of source temperatures, channel dimensions, openings, boundary conditions, and source locations on the heat transfer from and flow above the protruding sources are investigated. Different configurations of channel dimensions and separation distances of heat sources are considered and their effects on natural convection heat transfer characteristics are studied. The results show that the channel dimensions have a significant effect on fluid flow. However, their effects on heat transfer are found to be small. The separation distance is found to be an important parameter affecting the heat transfer rate. The numerical results of temperature profiles are compared with the experimental measurements performed using Filtered Rayleigh Scattering (FRS) technique in an earlier study, indicating good agreement. It is observed that adiabatic upper plate assumption leads to better temperature predictions than isothermal plate assumption.

The Effect of Hot-Streaks on HP Vane Surface and Endwall Heat Transfer: An Experimental and Numerical Study

2005 ◽  
Author(s):  
T. Povey ◽  
K. S. Chana ◽  
T. V. Jones ◽  
J. Hurrion
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Cooling System ◽  
Numerical Study ◽  
Inlet Temperature ◽  
Temperature Profiles ◽  
Wall Heat Transfer ◽  
Hot Streak ◽  
End Wall

Pronounced non-uniformities in combustor exit flow temperature (hot-streaks), which arise because of discrete injection of fuel and dilution air jets within the combustor and because of end-wall cooling flows, affect both component life and aerodynamics. Because it is very difficult to quantitatively predict the affects of these temperature non-uniformities on the heat transfer rates, designers are forced to budget for hot-streaks in the cooling system design process. Consequently, components are designed for higher working temperatures than the mass-mean gas temperature, and this imposes a significant overall performance penalty. An inadequate cooling budget can lead to reduced component life. An improved understanding of hot-streak migration physics, or robust correlations based on reliable experimental data, would help designers minimise the overhead on cooling flow that is currently a necessity. A number of recent research projects sponsored by a range of industrial gas turbine and aero-engine manufacturers attest to the growing interest in hot-streak physics. This paper presents measurements of surface and end-wall heat transfer rate for an HP nozzle guide vane (NGV) operating as part of a full HP turbine stage in an annular transonic rotating turbine facility. Measurements were conducted with both uniform stage inlet temperature and with two non-uniform temperature profiles. The temperature profiles were non-dimensionally similar to profiles measured in an engine. A difference of one half of an NGV pitch in the circumferential (clocking) position of the hot-streak with respect to the NGV was used to investigate the affect of clocking on the vane surface and end-wall heat transfer rate. The vane surface pressure distributions, and the results of a flow-visualisation study, which are also given, are used to aid interpretation of the results. The results are compared to two-dimensional predictions conducted using two different boundary layer methods. Experiments were conducted in the Isentropic Light Piston Facility (ILPF) at QinetiQ Farnborough, a short duration engine-size turbine facility. Mach number, Reynolds number and gas-to-wall temperature ratios were correctly modelled. It is believed that the heat transfer measurements presented in this paper are the first of their kind.

Sign in / Sign up

Export Citation Format

Share Document