scholarly journals Comparative modal analysis for a twisted beam axle for a hybrid vehicle

2022 ◽  
Vol 960 (1) ◽  
pp. 012009
Author(s):  
Laurian Tomşeanu ◽  
Viorel Nicolae ◽  
Ionel Vieru ◽  
Dănuţ Marinescu
Keyword(s):  
Comparative Analysis ◽  
Modal Analysis ◽  
Mass Production ◽  
Rear Axle ◽  
Hybrid Vehicle ◽  
Natural Mode ◽  
Cad Model ◽  
Twisted Beam ◽  
Beam Axle ◽  
Element Method

Abstract In this article it is presented a comparative analysis of natural mode frequencies for a non-powered rear axle used to fit mass production vehicle and for a similar rear axle derived from the first one to be used to fit a hybrid powered vehicle. The CAD model of the axle and the computed natural mode frequencies were realised using CATIA V5. For calculation, finit element method was used.

scholarly journals Dynamics Characteristics of Blast Furnace Shell

2011 ◽  
Vol 2-3 ◽  
pp. 1018-1020
Author(s):  
De Chen Zhang ◽  
Yan Ping Sun
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Blast Furnace ◽  
Modal Analysis ◽  
Natural Frequencies ◽  
Theoretical Foundation ◽  
Structural Mechanics ◽  
Mode Shapes ◽  
The Future ◽  
Element Method

Finite element method and structural mechanics method are used to study the blast furnace shell modal analysis and the natural frequencies and mode shapes have been calculated. The two methods were compared and validated , and the results provide a theoretical foundation for the anti-vibration capabilities design of blast furnace shell in the future .

Comparative analysis for five fixations of Pauwels-I by the biomechanical finite-element method

2018 ◽  
Vol 33 (5) ◽  
pp. 428-437 ◽  
Author(s):  
Matthew Jian-Qiao Peng ◽  
Hai-Yan Chen ◽  
XiangYang Ju ◽  
Yong Hu ◽  
Ashraf Ayoub ◽  
...  
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Comparative Analysis ◽  
Element Method

scholarly journals COMPARATIVE ANALYSIS OF MONOCORTICAL AND BICORTICAL METHODS OF INSTALLING MINI-IMPLANTS

2021 ◽  
pp. 38-40
Author(s):  
O.Yu. Rivis ◽  
V.S. Melnyk ◽  
M.V. Rivis ◽  
K.V. Zombor
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Comparative Analysis ◽  
Cortical Bone ◽  
Bone Tissue ◽  
Orthodontic Treatment ◽  
The Finite Element Method ◽  
Force Load ◽  
Mini Implants ◽  
Element Method

The aim of the study. Carry out a comparative analysis of the support ability of human jaw bone tissue in monocortical and bicortical installation of a mini-implant of own design OMG. Research methods. In order to study biomechanical characteristics of developed OMG mini-implant and bone tissue capacity during monocortical and bicortical installation, the finite element method (MSE) was used. The scheme and finite element 2-D model of bicortical installation of OMG mini-implant (length 8 mm, diameter 1.8 mm) provided full penetration through one layer of cortical bone equal to 1 mm, the entire cancellous bone and immersion in the second layer of cortical bone by 0, 5 mm. No implantation was immersed in the second cortical layer of bone during monocortical installation. A single force load of 1 N was applied in the horizontal direction parallel to the cortical plate of the bone. Results of the study. One of the most important factors leading to the success of the use of a mini-implant is its stability in the process of orthodontic treatment. Quite a high level of failure in the monocortical installation of mini-screws has led to the search for better methods to ensure the stability of their use. This was a bicortical method of fixation, based on the placement of the minig screw in the thickness of the two cortical plates of the jaws. Area for such installation of mini-screws can be a site of a palate and alveolar sprouts at installation of miniimplants through all its thickness. As shown by our data on the use of the finite element method under the force load of the biomechanical system "bone - mini-implant", the stress concentration zone is located in the area of the cortical bone of the jaw. The results of the calculation of the maximum stresses (σmax, MPa) and the maximum possible displacements (umax, mm) of the mini-implant in the biomechanical system "bone - mini-implant" in monocortical installation were, respectively, 8.27 MPa and 0.300 * 10-8 mm and in bicortical installation 6.00 MPa and 0.201 * 10-8 mm. The bicortical method of fixing the mini-implant in the jaw bones significantly increases the ability to resist deformation of this type of biomechanical system under force loads of the mini-implant. In the bicortical method of mini-implant placement, the extreme values of equivalent according to Mises stresses in the upper part of the cortical bone of the jaw are reduced by 27%. This can be explained by a significant increase in the area of contact due to the two layers of the cortical bone of the jaw with the surface of the mini-implant. Conclusion. The bicortical method of installing mini-implants is a more effective and reliable way to provide skeletal support during orthodontic treatment.

Sign in / Sign up

Export Citation Format

Share Document