scholarly journals 2-D multiparameter viscoelastic shallow-seismic full-waveform inversion: reconstruction tests and first field-data application

2020 ◽  
Vol 222 (1) ◽  
pp. 560-571
Author(s):  
Lingli Gao ◽  
Yudi Pan ◽  
Thomas Bohlen
Keyword(s):  
Wave Velocity ◽  
Wave Attenuation ◽  
Waveform Inversion ◽  
P Wave ◽  
S Wave ◽  
Velocity Models ◽  
Full Waveform ◽  
Shallow Seismic ◽  
P Wave Velocity ◽  
Data Application

SUMMARY 2-D full-waveform inversion (FWI) of shallow-seismic wavefields has recently become a novel way to reconstruct S-wave velocity models of the shallow subsurface with high vertical and lateral resolution. In most applications, seismic wave attenuation is ignored or considered as a passive modelling parameter only. In this study, we explore the feasibility and performance of multiparameter viscoelastic 2-D FWI in which seismic velocities and attenuation of P and S waves, respectively, and mass density are inverted simultaneously. Synthetic reconstruction experiments reveal that multiple crosstalks between all viscoelastic material parameters may occur. The reconstruction of S-wave velocity is always robust and of high quality. The parameters P-wave velocity and density exhibit weaker sensitivity and can be reconstructed more reliably by multiparameter viscoelastic FWI. Anomalies in S-wave attenuation can be recovered but with limited resolution. In a field-data application, a small-scale refilled trench is nicely delineated as a low P- and S-wave velocity anomaly. The reconstruction of P-wave velocity is improved by the simultaneous inversion of attenuation. The reconstructed S-wave attenuation reveals higher attenuation in the shallow weathering zone and weaker attenuation below. The variations in the reconstructed P- and S-wave velocity models are consistent with the reflectivity observed in a ground penetrating radar (GPR) profile.

scholarly journals Time–frequency windowing in multiparameter elastic FWI of shallow seismic wavefield

2020 ◽  
Vol 222 (2) ◽  
pp. 1164-1177
Author(s):  
Nikolaos Athanasopoulos ◽  
Edgar Manukyan ◽  
Thomas Bohlen ◽  
Hansruedi Maurer
Keyword(s):  
Wave Velocity ◽  
Time Window ◽  
Mass Density ◽  
Waveform Inversion ◽  
P Wave ◽  
S Wave ◽  
Time Frequency ◽  
Full Waveform ◽  
Shallow Seismic ◽  
P Wave Velocity

SUMMARY Full-waveform inversion of shallow seismic wavefields is a promising method to infer multiparameter models of elastic material properties (S-wave velocity, P-wave velocity and mass density) of the shallow subsurface with high resolution. Previous studies used either the refracted Pwaves to reconstructed models of P-wave velocity or the high-amplitude Rayleigh waves to infer the S-wave velocity structure. In this work, we propose a combination of both wavefields using continuous time–frequency windowing. We start with the contribution of refracted P waves and gradually increase the time window to account for scattered body waves, higher mode Rayleigh waves and finally the fundamental Rayleigh wave mode. The opening of the time window is combined with opening the frequency bandwidth of input signals to avoid cycle skipping. Synthetic reconstruction tests revealed that the reconstruction of P-wave velocity model and mass density can be improved. The S-wave velocity reconstruction is still accurate and robust and is slightly benefitted by time–frequency windowing. In a field data application, we observed that time–frequency windowing improves the consistency of multiparameter models. The inferred models are in good agreement with independent geophysical information obtained from ground-penetrating radar and full-waveform inversion of SH waves.

scholarly journals Interparameter trade-off quantification for isotropic-elastic full-waveform inversion with various model parameterizations

Geophysics ◽  
2019 ◽  
Vol 84 (2) ◽  
pp. R185-R206 ◽  
Author(s):  
Wenyong Pan ◽  
Kristopher A. Innanen ◽  
Yu Geng ◽  
Junxiao Li
Keyword(s):  
Wave Velocity ◽  
Waveform Inversion ◽  
P Wave ◽  
Physical Parameters ◽  
Full Waveform Inversion ◽  
S Wave ◽  
Trade Off ◽  
Full Waveform ◽  
Trade Offs ◽  
P Wave Velocity

Simultaneous determination of multiple physical parameters using full-waveform inversion (FWI) suffers from interparameter trade-off difficulties. Analyzing the interparameter trade-offs in different model parameterizations of isotropic-elastic FWI, and thus determining the appropriate model parameterization, are critical for efficient inversion and obtaining reliable inverted models. Five different model parameterizations are considered and compared including velocity-density, modulus-density, impedance-density, and two velocity-impedance parameterizations. The scattering radiation patterns are first used for interparameter trade-off analysis. Furthermore, a new framework is developed to evaluate the interparameter trade-off based upon multiparameter Hessian-vector products: Multiparameter point spread functions (MPSFs) and interparameter contamination sensitivity kernels (ICSKs), which provide quantitative, second-order measurements of the interparameter contaminations. In the numerical experiments, the interparameter trade-offs in various model parameterizations are evaluated using the MPSFs and ICSKs. Inversion experiments are carried out with simple Gaussian-anomaly models and a complex Marmousi model. Overall, the parameterization of the P-wave velocity, S-wave velocity, and density, and the parameterization of the P-wave velocity, S-wave velocity, and S-wave impedance perform best for reconstructing all of the physical parameters. Isotropic-elastic FWI of the Hussar low-frequency data set with various model parameterizations verifies our conclusions.

scholarly journals Elastic reflection-based waveform inversion with a nonlinear approach

Geophysics ◽  
2017 ◽  
Vol 82 (6) ◽  
pp. R309-R321 ◽  
Author(s):  
Qiang Guo ◽  
Tariq Alkhalifah
Keyword(s):  
Wave Velocity ◽  
Equivalent Stress ◽  
Waveform Inversion ◽  
P Wave ◽  
S Wave ◽  
Velocity Models ◽  
Wave Velocities ◽  
Full Waveform ◽  
Highly Nonlinear ◽  
Elastic Reflection

Full-waveform inversion (FWI) is a highly nonlinear problem due to the complex reflectivity of the earth, and this nonlinearity only increases under the more expensive elastic assumption. In elastic media, we need a good initial P-wave velocity and even better initial S-wave velocity models with accurate representation of the low model wavenumbers for FWI to converge. However, inverting for the low-wavenumber components of P- and S-wave velocities using reflection waveform inversion (RWI) with an objective to fit the reflection shape, rather than produce reflections, may mitigate the limitations of FWI. Because FWI, performing as a migration operator, is preferred of the high-wavenumber updates along reflectors. We have developed an elastic RWI that inverts for the low-wavenumber and perturbation components of the P- and S-wave velocities. To generate the full elastic reflection wavefields, we derive an equivalent stress source made up by the inverted model perturbations and incident wavefields. We update the perturbation and propagation parts of the velocity models in a nested fashion. Applications on the synthetic isotropic models and field data indicate that our method can efficiently update the low- and high-wavenumber parts of the models.

Joint petrophysical full-waveform inversion of the shallow-seismic and multi-offset GPR data

2021 ◽  
Author(s):  
Tan Qin ◽  
Thomas Bohlen ◽  
Yudi Pan
Keyword(s):  
Dielectric Permittivity ◽  
Wave Velocity ◽  
Waveform Inversion ◽  
P Wave ◽  
Relative Dielectric Permittivity ◽  
Full Waveform Inversion ◽  
S Wave ◽  
Petrophysical Parameters ◽  
Full Waveform ◽  
Shallow Seismic

<p>Shallow-seismic surface wave and ground penetrating radar (GPR) are employed in a wide range of engineering and geosciences applications. Full-waveform inversion (FWI) of either seismic or multi-offset GPR data are able to provide high-resolution subsurface characterization and have received particular attention in the past decade. Those two geophysical methods are involved in the increasing requirements of comprehensive site and material investigations. However, it is still challenging to provide an effective integration between seismic data and electromagnetic data. In this paper, we investigated the joint petrophysical inversion (JPI) of shallow-seismic and multi-offset GPR data for more consistent imaging of near surface. As a bridge between the seismic parameters (P-wave velocity, S-wave velocity, and density) and GPR parameters (relative dielectric permittivity and electric conductivity), the petrophysical relationships with the parameters namely porosity and saturation are employed to link two data sets. We first did a sensitivity analysis of the petrophysical parameters to the seismic and GPR parameters and then determined an efficient integration of using shallow-seismic FWI to update porosity and GPR FWI to update saturation, respectively. A comparison of several parameterisation combinations shows that the seismic velocity parameterisation in shallow-seismic FWI and a modified logarithm parameterisation in GPR FWI works well in reconstructing reliable S-wave velocity and relative dielectric permittivity models, respectively. With the help from the petrophysical links, we realized JPI by transforming those well recovered parameters to the petrophysical parameters and then to other seismic and GPR parameters. A synthetic test indicates that, compared with the individual petrophysical inversion and individual FWI, JPI outperforms in simultaneously reconstructing all seismic, GPR, and petrophysical parameters with higher resolution and improved details. It is proved that JPI would be a potential data integration approach for the shallow subsurface investigation.</p>

A hierarchical elastic full-waveform inversion scheme based on wavefield separation and the multistep-length approach

Geophysics ◽  
2016 ◽  
Vol 81 (3) ◽  
pp. R99-R123 ◽  
Author(s):  
Zhiming Ren ◽  
Yang Liu
Keyword(s):  
Wave Velocity ◽  
Waveform Inversion ◽  
P Wave ◽  
Model Parameters ◽  
Full Waveform Inversion ◽  
S Wave ◽  
Wave Velocities ◽  
Full Waveform ◽  
Wavefield Separation ◽  
P Wave Velocity

Elastic full-waveform inversion (FWI) updates model parameters by minimizing the residuals of the P- and S-wavefields, resulting in more local minima and serious nonlinearity. In addition, the coupling of different parameters degrades the inversion results. To address these problems, we have developed a hierarchical elastic FWI scheme based on wavefield separation and a multistep-length gradient approach. First, we have derived the gradients expressed by different wave modes; analyzed the crosstalk between various parameters; and evaluated the sensitivity of separated P-wave, separated S-wave, and P- and S-wave misfit functions. Then, a practical four-stage inversion workflow was developed. In the first stage, conventional FWI is used to achieve rough estimates of the P- and S-wave velocities. In the second stage, we only invert the P-wave velocity applying the separated P-wavefields when strong S-wave energy is involved, or we merely update the S-wave velocity by matching the separated S-wavefields for the weak S-wave case. The PP and PS gradient formulas are used in these two cases, respectively. Therefore, the nonlinearity of inversion and the crosstalk between parameters are greatly reduced. In the third stage, the multistep-length gradient scheme is adopted. The density structure can be improved owing to the use of individual step lengths for different parameters. In the fourth stage, we make minor adjustments to the recovered P- and S-wave velocities and density by implementing conventional FWI again. Synthetic examples have determined that our hierarchical FWI scheme with the aforementioned steps obtains more plausible models than the conventional method. Inversion results of each stage and any three stages reveal that wavefield decomposition and the multistep-length approach are helpful to improve the accuracy of velocities and density, respectively, and all the stages of our hierarchical FWI method are necessary to give a good recovery of P- and S-wave velocities and density.

Multi-parameter model building for the Qiuyue structure using four-component ocean-bottom seismometer data

Geophysics ◽  
2021 ◽  
pp. 1-52
Author(s):  
Yuzhu Liu ◽  
Xinquan Huang ◽  
Jizhong Yang ◽  
Xueyi Liu ◽  
Bin Li ◽  
...  
Keyword(s):  
Wave Velocity ◽  
Waveform Inversion ◽  
Velocity Model ◽  
P Wave ◽  
Velocity Analysis ◽  
Full Waveform Inversion ◽  
Ocean Bottom ◽  
Ocean Bottom Seismometer ◽  
Full Waveform ◽  
P Wave Velocity

Thin sand-mud-coal interbedded layers and multiples caused by shallow water pose great challenges to conventional 3D multi-channel seismic techniques used to detect the deeply buried reservoirs in the Qiuyue field. In 2017, a dense ocean-bottom seismometer (OBS) acquisition program acquired a four-component dataset in East China Sea. To delineate the deep reservoir structures in the Qiuyue field, we applied a full-waveform inversion (FWI) workflow to this dense four-component OBS dataset. After preprocessing, including receiver geometry correction, moveout correction, component rotation, and energy transformation from 3D to 2D, a preconditioned first-arrival traveltime tomography based on an improved scattering integral algorithm is applied to construct an initial P-wave velocity model. To eliminate the influence of the wavelet estimation process, a convolutional-wavefield-based objective function for the preprocessed hydrophone component is used during acoustic FWI. By inverting the waveforms associated with early arrivals, a relatively high-resolution underground P-wave velocity model is obtained, with updates at 2.0 km and 4.7 km depth. Initial S-wave velocity and density models are then constructed based on their prior relationships to the P-wave velocity, accompanied by a reciprocal source-independent elastic full-waveform inversion to refine both velocity models. Compared to a traditional workflow, guided by stacking velocity analysis or migration velocity analysis, and using only the pressure component or other single-component, the workflow presented in this study represents a good approach for inverting the four-component OBS dataset to characterize sub-seafloor velocity structures.

Physical Properties and Structure of the Near Subsurface in the Săcel Area, Romania, from Shallow Seismic Measurements

2019 ◽  
Vol 24 (1) ◽  
pp. 151-158
Author(s):  
Ionelia Panea
Keyword(s):  
Wave Velocity ◽  
Signal To Noise Ratio ◽  
Soil Surface ◽  
Geological Structure ◽  
P Wave ◽  
S Wave ◽  
Sedimentary Deposits ◽  
Shallow Seismic ◽  
P Wave Velocity ◽  
Good Signal

Results are presented for shallow seismic reflection measurements performed southwest of Săcel village in Romania for the purpose of obtaining information about the geological structure in the near subsurface. The P-wave and S-wave velocity distributions were also obtained below the soil surface. The measurements were performed along a nearly linear profile on the top of an elongated hill. Most of the shot gathers were characterized by a good signal-to-noise ratio. A depth-converted migrated section was obtained after the processing of shot gathers, on which an image of sedimentary deposits with various thicknesses, separated by shallow faults until a depth of about 80 m, were observed. The P-wave and S-wave velocity-depth models for two segments were of considerable interest for a geotechnical study proposed for the construction of a windmill park. The two- and three-layered P-wave velocity-depth models were comparable until depths of about 10 m after first-arrival traveltime inversions. The lateral variations in the subsurface geological structure and lithology reflected the variations in the P-wave velocity values from both models. The S-wave velocity-depth models for comparable depth intervals were similar to those from the P-wave velocity-depth models. Reliable S-wave velocity distributions were obtained after inversion of fundamental-mode and higher-mode surface waves.

scholarly journals The Local Earthquake Tomography of Erzurum (Turkey) Geothermal Area

2019 ◽  
Vol 23 (3) ◽  
pp. 209-223 ◽  
Author(s):  
Caglar Ozer ◽  
Mehmet Ozyazicioglu
Keyword(s):  
Wave Velocity ◽  
Seismic Velocity ◽  
Three Dimensional ◽  
P Wave ◽  
Geothermal Area ◽  
S Wave ◽  
Velocity Models ◽  
Local Earthquake Tomography ◽  
P Wave Velocity ◽  
Local Earthquake

Erzurum and its surroundings are one of the seismically active and hydrothermal areas in the Eastern part of Turkey. This study is the first approach to characterize the crust by seismic features by using the local earthquake tomography method. The earthquake source location and the three dimensional seismic velocity structures are solved simultaneously by an iterative tomographic algorithm, LOTOS-12. Data from a combined permanent network comprising comprises of 59 seismometers which was installed by Ataturk University-Earthquake Research Center and Earthquake Department of the Disaster and Emergency Management Authority  to monitor the seismic activity in the Eastern Anatolia, In this paper, three-dimensional Vp and Vp/Vs characteristics of Erzurum geothermal area were investigated down to 30 km by using 1685 well-located earthquakes with 29.894 arrival times, consisting of 17.298 P- wave and 12.596 S- wave arrivals. We develop new high-resolution depth-cross sections through Erzurum and its surroundings to provide the subsurface geological structure of seismogenic layers and geothermal areas. We applied various size horizontal and vertical checkerboard resolution tests to determine the quality of our inversion process. The basin models are traceable down to 3 km depth, in terms of P-wave velocity models. The higher P-wave velocity areas in surface layers are related to the metamorphic and magmatic compact materials. We report that the low Vp and high Vp/Vs values are observed in Yedisu, Kaynarpinar, Askale, Cimenozu, Kaplica, Ovacik, Yigitler, E part of Icmeler, Koprukoy, Uzunahmet, Budakli, Soylemez, Koprukoy, Gunduzu, Karayazi, Icmesu, E part of Horasan and Kaynak regions indicated geothermal reservoir.

scholarly journals Semiglobal viscoacoustic full-waveform inversion

Geophysics ◽  
2019 ◽  
Vol 84 (2) ◽  
pp. R271-R293 ◽  
Author(s):  
Nuno V. da Silva ◽  
Gang Yao ◽  
Michael Warner
Keyword(s):  
Physical Properties ◽  
Wave Velocity ◽  
Seismic Data ◽  
Waveform Inversion ◽  
P Wave ◽  
Full Waveform Inversion ◽  
Data Set ◽  
Intrinsic Attenuation ◽  
Full Waveform ◽  
P Wave Velocity

Full-waveform inversion deals with estimating physical properties of the earth’s subsurface by matching simulated to recorded seismic data. Intrinsic attenuation in the medium leads to the dispersion of propagating waves and the absorption of energy — media with this type of rheology are not perfectly elastic. Accounting for that effect is necessary to simulate wave propagation in realistic geologic media, leading to the need to estimate intrinsic attenuation from the seismic data. That increases the complexity of the constitutive laws leading to additional issues related to the ill-posed nature of the inverse problem. In particular, the joint estimation of several physical properties increases the null space of the parameter space, leading to a larger domain of ambiguity and increasing the number of different models that can equally well explain the data. We have evaluated a method for the joint inversion of velocity and intrinsic attenuation using semiglobal inversion; this combines quantum particle-swarm optimization for the estimation of the intrinsic attenuation with nested gradient-descent iterations for the estimation of the P-wave velocity. This approach takes advantage of the fact that some physical properties, and in particular the intrinsic attenuation, can be represented using a reduced basis, substantially decreasing the dimension of the search space. We determine the feasibility of the method and its robustness to ambiguity with 2D synthetic examples. The 3D inversion of a field data set for a geologic medium with transversely isotropic anisotropy in velocity indicates the feasibility of the method for inverting large-scale real seismic data and improving the data fitting. The principal benefits of the semiglobal multiparameter inversion are the recovery of the intrinsic attenuation from the data and the recovery of the true undispersed infinite-frequency P-wave velocity, while mitigating ambiguity between the estimated parameters.

Elastic reflection traveltime inversion with decoupled wave equation

Geophysics ◽  
2018 ◽  
Vol 83 (5) ◽  
pp. R463-R474 ◽  
Author(s):  
Guanchao Wang ◽  
Shangxu Wang ◽  
Jianyong Song ◽  
Chunhui Dong ◽  
Mingqiang Zhang
Keyword(s):  
Wave Equation ◽  
Wave Velocity ◽  
Waveform Inversion ◽  
P Wave ◽  
Model Parameters ◽  
Local Minima ◽  
S Wave ◽  
Traveltime Inversion ◽  
Velocity Models ◽  
Elastic Reflection

Elastic full-waveform inversion (FWI) updates high-resolution model parameters by minimizing the residuals of multicomponent seismic records between the field and model data. FWI suffers from the potential to converge to local minima and more serious nonlinearity than acoustic FWI mainly due to the absence of low frequencies in seismograms and the extended model domain (P- and S-velocities). Reflection waveform inversion can relax the nonlinearity by relying on the tomographic components, which can be used to update the low-wavenumber components of the model. Hence, we have developed an elastic reflection traveltime inversion (ERTI) approach to update the low-wavenumber component of the velocity models for the P- and S-waves. In our ERTI algorithm, we took the P- and S-wave impedance perturbations as elastic reflectivity to generate reflections and a weighted crosscorrelation as the misfit function. Moreover, considering the higher wavenumbers (lower velocity value) of the S-wave velocity compared with the P-wave case, optimizing the low-wavenumber components for the S-wave velocity is even more crucial in preventing the elastic FWI from converging to local minima. We have evaluated an equivalent decoupled velocity-stress wave equation to ERTI to reduce the coupling effects of different wave modes and to improve the inversion result of ERTI, especially for the S-wave velocity. The subsequent application on the Sigsbee2A model demonstrates that our ERTI method with the decoupled wave equation can efficiently update the low-wavenumber parts of the model and improve the precision of the S-wave velocity.

Sign in / Sign up

Export Citation Format

Share Document