scholarly journals Articulation and growth of skeletal elements in balanid barnacles (Balanidae, Balanomorpha, Cirripedia)

2019 ◽  
Vol 6 (9) ◽  
pp. 190458 ◽  
Author(s):  
Antonio G. Checa ◽  
Carmen Salas ◽  
Alejandro B. Rodríguez-Navarro ◽  
Christian Grenier ◽  
Nelson A. Lagos
Keyword(s):  
Calcium Carbonate ◽  
Cellular Tissue ◽  
Growth Increment ◽  
Basal Plate ◽  
Viscous Fingers ◽  
Internal Surfaces ◽  
Base Plates

The morphology and ultrastructure of the shells of two balanid species have been examined, paying special attention to the three types of boundaries between plates: (i) radii-parietes, (ii) alae-sheaths, and (iii) parietes-basal plate. At the carinal surfaces of the radii and at the rostral surfaces of the alae, there are series of crenulations with dendritic edges. The crenulations of the radius margins interlock with less prominent features of the opposing paries margins, whereas the surfaces of the longitudinal abutments opposing the ala margins are particularly smooth. The primary septa of the parietes also develop dendritic edges, which abut the internal surfaces of the primary tubes of the base plates. In all cases, there are chitino-proteinaceous organic membranes between the abutting structures. Our observations indicate that the very edges of the crenulations and the primary septa are permanently in contact with the organic membranes. We conclude that, when a new growth increment is going to be produced, the edges of both the crenulations and the primary septa pull the viscoelastic organic membranes locally, with the consequent formation of viscous fingers. For the abutting edges to grow, calcium carbonate must diffuse across the organic membranes, but it is not clear how growth of the organic membranes themselves is accomplished, in the absence of any cellular tissue.

Replication of Internal Biological Surfaces

1972 ◽  
Vol 30 ◽  
pp. 308-309
Author(s):  
J. A. Nowell ◽  
J. Pangborn ◽  
W. S. Tyler
Keyword(s):  
Da Vinci ◽  
Leonardo Da Vinci ◽  
Rat Lung ◽  
Tubular Structures ◽  
Cerebral Ventricles ◽  
Internal Surfaces ◽  
Biological Surfaces ◽  
Dog Kidney ◽  
Lung And Kidney ◽  
Scanning Electron

Leonardo da Vinci in the 16th century, used injection replica techniques to study internal surfaces of the cerebral ventricles. Developments in replicating media have made it possible for modern morphologists to examine injection replicas of lung and kidney with the scanning electron microscope (SEM). Deeply concave surfaces and interrelationships to tubular structures are difficult to examine with the SEM. Injection replicas convert concavities to convexities and tubes to rods, overcoming these difficulties.Batson's plastic was injected into the renal artery of a horse kidney. Latex was injected into the pulmonary artery and cementex in the trachea of a cat. Following polymerization the tissues were removed by digestion in concentrated HCl. Slices of dog kidney were aldehyde fixed by immersion. Rat lung was aldehyde fixed by perfusion via the trachea at 30 cm H2O. Pieces of tissue 10 x 10 x 2 mm were critical point dried using CO2. Selected areas of replicas and tissues were coated with silver and gold and examined with the SEM.

A TEM study of the microstructure of avian eggshells

1992 ◽  
Vol 50 (2) ◽  
pp. 1102-1103
Author(s):  
S. Q. Xiao ◽  
S. Baden ◽  
A. H. Heuer
Keyword(s):  
Electron Microscope ◽  
Calcium Carbonate ◽  
Nucleation And Growth ◽  
Growth Mechanisms ◽  
Shell Surface ◽  
Thin Sections ◽  
Polycrystalline Metals ◽  
Transmission Electron ◽  
Nucleation And Growth Mechanisms

The avian eggshell is one of the most rapidly mineralizing biological systems known. In situ, 5g of calcium carbonate are crystallized in less than 20 hrs to fabricate the shell. Although there have been much work about the formation of eggshells, controversy about the nucleation and growth mechanisms of the calcite crystals, and their texture in the eggshell, still remain unclear. In this report the microstructure and microchemistry of avian eggshells have been analyzed using transmission electron microscope (TEM) and energy dispersive spectroscopy (EDS).Fresh white and dry brown eggshells were broken and fixed in Karnosky's fixative (kaltitanden) for 2 hrs, then rinsed in distilled H2O. Small speckles of the eggshells were embedded in Spurr medium and thin sections were made ultramicrotome.The crystalline part of eggshells are composed of many small plate-like calcite grains, whose plate normals are approximately parallel to the shell surface. The sizes of the grains are about 0.3×0.3×1 μm3 (Fig.l). These grains are not as closely packed as man-made polycrystalline metals and ceramics, and small gaps between adjacent grains are visible indicating the absence of conventional grain boundaries.

Scaling risk assessment in a closed circuit recycled board mill by speciation methods

TAPPI Journal ◽  
2012 ◽  
Vol 11 (5) ◽  
pp. 53-61 ◽  
Author(s):  
PATRICK HUBER ◽  
SYLVIE NIVELON ◽  
PATRICE NORTIER
Keyword(s):  
Calcium Carbonate ◽  
Volatile Fatty Acids ◽  
Inorganic Carbon ◽  
Stability Index ◽  
Closed Circuit ◽  
Critical Problem ◽  
Local Scaling ◽  
Water Analyses ◽  
Closed Water ◽  
Speciation Calculation

Calcium carbonate scaling often is a critical problem for recycled board mills that have closed water circuits. The objective of this study was to determine local scaling risks throughout the production process. To predict scaling potential, we calculated several saturation indexes, based on speciation determined from detailed water analyses. Calculated scaling trends are in accordance with observed dissolution and precipitation of calcium carbonate in the process, when considering local aeration phenomena. The importance of volatile fatty acids (resulting from anaerobic bacterial activity) in calco-carbonic equilibriums is discussed, and taken into account in the speciation calculation. We also demonstrate the need to measure inorganic carbon instead of alkalinity in such conditions. This makes typical scaling indexes, such as the Ryznar Stability Index, irrelevant to predict scaling risk in closed circuit conditions; thus, it is necessary to use general speciation methods, as described in this paper.

A method for measuring the in-plane compressive strength and the compression behavior of coating layers

TAPPI Journal ◽  
2011 ◽  
Vol 10 (7) ◽  
pp. 29-34
Author(s):  
TEEMU PUHAKKA ◽  
ISKO KAJANTO ◽  
NINA PYKÄLÄINEN
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Calcium Carbonate ◽  
Coating Layer ◽  
Test Methods ◽  
Coating Films ◽  
Precipitated Calcium Carbonate ◽  
Coating Color ◽  
Mineral Coatings ◽  
Styrene Butadiene

Cracking at the fold is a quality defect sometimes observed in coated paper and board. Although tensile and compressive stresses occur during folding, test methods to measure the compressive strength of a coating have not been available. Our objective was to develop a method to measure the compressive strength of a coating layer and to investigate how different mineral coatings behave under compression. We used the short-span compressive strength test (SCT) to measure the in-plane compressive strength of a free coating layer. Unsupported free coating films were prepared for the measurements. Results indicate that the SCT method was suitable for measuring the in-plane compressive strength of a coating layer. Coating color formulations containing different kaolin and calcium carbonate minerals were used to study the effect of pigment particles’ shape on the compressive and tensile strengths of coatings. Latices having two different glass transition temperatures were used. Results showed that pigment particle shape influenced the strength of a coating layer. Platy clay gave better strength than spherical or needle-shaped carbonate pigments. Compressive and tensile strength decreased as a function of the amount of calcium carbonate in the coating color, particularly with precipitated calcium carbonate. We also assessed the influence of styrene-butadiene binder on the compressive strength of the coating layer, which increased with the binder level. The compressive strength of the coating layer was about three times the tensile strength.

The solubility of calcium carbonate  in green liquor handling systems

TAPPI Journal ◽  
2019 ◽  
Vol 18 (10) ◽  
pp. 595-602
Author(s):  
ALISHA GIGLIO ◽  
VLADIMIROS G. PAPANGELAKIS ◽  
HONGHI TRAN
Keyword(s):  
Calcium Carbonate ◽  
Systematic Study ◽  
Kraft Pulp ◽  
Thermodynamic Simulation ◽  
Solubility Data ◽  
Pulp Mills ◽  
Persistent Problem ◽  
Green Liquor ◽  
Kraft Pulp Mills ◽  
Salt Systems

The formation of hard calcite (CaCO3) scale in green liquor handling systems is a persistent problem in many kraft pulp mills. CaCO3 precipitates when its concentration in the green liquor exceeds its solubility. While the solubility of CaCO3 in water is well known, it is not so in the highly alkaline green liquor environment. A systematic study was conducted to determine the solubility of CaCO3 in green liquor as a function of temperature, total titratable alkali (TTA), causticity, and sulfidity. The results show that the solubility increases with increased temperature, increased TTA, decreased causticity, and decreased sulfidity. The new solubility data was incorporated into OLI (a thermodynamic simulation program for aqueous salt systems) to generate a series of CaCO3 solubility curves for various green liquor conditions. The results help explain how calcite scale forms in green liquor handling systems.

DC Partial Discharge Characteristics of Polyphenylenesulfide / Calcium Carbonate Composite Insulating Material

2017 ◽  
Vol 137 (9) ◽  
pp. 536-541
Author(s):  
Tomohiro Kawashima ◽  
Tomohiro Yamada ◽  
Yoshinobu Murakami ◽  
Masayuki Nagao ◽  
Sou Ozaki ◽  
...  
Keyword(s):  
Calcium Carbonate ◽  
Partial Discharge ◽  
Discharge Characteristics ◽  
Insulating Material

Mathematical Model of Flat Surface Machining Inaccuracies due to Elastic Strains of Technological System

2018 ◽  
pp. 1-14 ◽  
Author(s):  
I. I. Kravchenko
Keyword(s):  
Mathematical Model ◽  
Vector Field ◽  
Model Development ◽  
Technological System ◽  
Mutual Arrangement ◽  
Real Surface ◽  
Main Bearing ◽  
Flat Surfaces ◽  
Internal Surfaces ◽  
Elastic Strains

The paper considers the mathematical model development technique to build a vector field of the shape deviations when machining flat surfaces of shell parts on multi-operational machines under conditions of anisotropic rigidity in technological system (TS). The technological system has an anisotropic rigidity, as its elastic strains do not obey the accepted concepts, i.e. the rigidity towards the coordinate axes of the machine is the same, and they occur only towards the external force. The record shows that the diagrams of elastic strains of machine units are substantially different from the circumference. The issues to ensure the specified accuracy require that there should be mathematical models describing kinematic models and physical processes of mechanical machining under conditions of the specific TS. There are such models for external and internal surfaces of rotation [2,3], which are successfully implemented in practice. Flat surfaces (FS) of shell parts (SP) are both assembly and processing datum surfaces. Therefore, on them special stipulations are made regarding deviations of shape and mutual arrangement. The axes of the main bearing holes are coordinated with respect to them. The joints that ensure leak tightness and distributed load on the product part are closed on these surfaces. The paper deals with the analytical construction of the vector field F, which describes with appropriate approximation the real surface obtained as a result of modeling the process of machining flat surfaces (MFS) through face milling under conditions of anisotropic properties.

Sign in / Sign up

Export Citation Format

Share Document