Numerical Investigation into the Influence of Grain Orientation Distribution on the Local and Global Elastic-Plastic Behaviour of Polycrystalline Nickel-Based Superalloy INC-738 LC

Polycrystalline nickel-based superalloys tend to have large grains within component areas where high loads are dominant during operation. Due to these large grains, caused by the manufacturing and cooling process, the orientation of each grain becomes highly important, since it influences the elastic and plastic behaviour of the material. With the usage of the open source codes NEPER and FEPX, polycrystalline models of Inconel 738 LC were generated and their elastic and crystal plasticity behaviour simulated in dependence of different orientation distributions under uniaxial loading. Orientation distributions close to the [100] direction showed the lowest Young’s moduli as well as the highest elastic strains before yielding, as expected. Orientations close to the [5¯89] direction, showed the lowest elastic strains and therefore first plastic deformation under strain loading due to the highest shear stress in the slip systems caused by the interaction of Young’s modulus and the Schmid factor.

Experimental Research of Ratio between Residual and Elastic Strains eres/eE in High-Strength Concrete Beams Subjected to Bending

In the mechanics of concrete constructions, one distinguishes between residual and elastic strains. Cyclic loadings evoke changes mainly in the elastic strains; however, the total strains are decided by the sum of the residual and elastic strains. The knowledge of the ratio between the residual and total strains allows to predict the total deformations of a construction assuming it is made from an ideally elastic material. This paper presents the effect of the load level at the values of the residual strains for beams made of high-strength concretes and subjected to bending. The investigations showed that the share of residual strains for these concretes differed from the share of residual strains for concretes of lower classes. The investigations were made for cyclically loaded concrete samples and ferroconcrete beams for various relative load levels. The ratio between the residual and total strains was presented in the form of a dependence on the relative load level of the element. An important conclusion was that, after the crack formation, the share of residual stresses reduced, along with the increase in the concrete strength and elastic features of the construction which started to predominate.

In Situ Synchrotron X-Ray Micro-Diffraction Investigation of Elastic Strains in Laminated Ti-Al Composites

Spatially resolved elastic strains in the bulk interior of a laminated Ti-Al metal composite were studied during in situ tensile loading at strains up to 1.66% by a synchrotron-based micro-diffraction technique, namely differential aperture X-ray microscopy (DAXM). For both Al and Ti grains, deviatoric elastic strains were estimated based on polychromatic X-ray microbeam diffraction, while lattice strains along the normal direction of the tensile sample were directly measured using monochromatic X-ray microbeam diffraction. The estimated deviatoric strains show large spatial variations, and the mean values are consistent with the external loading conditions, i.e., increasing tensile strain along the tensile direction and increasing compressive strain along the sample normal with increasing loading. The directly measured lattice strains also show large spatial variations, although the magnitude of this variation is smaller than that for the estimated deviatoric strain. The directly measured lattice strains in Ti grains are largely consistent with the external loading, whereas those in Al grains are in contradiction with the external loading. The causes of the experimental results are discussed and related to both the laminated microstructure of the composite material and the limitations of the techniques.

Elastic strains of quartz inclusions and microstructures from pressure solution in garnet reveal orientation and low magnitude of differential stress during subduction metamorphism

<p>Determining the stress state during metamorphism is a key challenge in metamorphic petrology as the effect of differential stress on metamorphic reactions is currently debated. Conventional piezometry generally gives stresses that correspond to overprinting deformation rather than to mineral growth of high-grade metamorphism, so an alternative approach is required. Garnetite lenses from the ultrahigh-pressure, low-temperature metamorphic Lago di Cignana unit (Western Alps, Italy) record compaction by a high degree of mineral dissolution in the fluid-rich environment of a cold subduction zone. This work combines microstructural analysis of deformed garnet with elastic strains of quartz inclusions to study the stresses in these metasedimentary rocks.</p><p>Garnet exhibits abundant evidence for incongruent pressure solution (IPS), most notably as truncated zones that mismatch across grain boundaries, interlocking structures, and shape-preferred orientation (SPO). The gap in garnet compositions represented by overgrown truncated zonation corresponds to undeformed garnet with inclusions of quartz and coesite, indicating that IPS operated during prograde to peak metamorphism. The distribution of aspect ratios in the garnet grain population suggests that pressure solution preferentially affected smaller grains. SPO analysis of many subregions across a garnetite sample reveals a complex distribution, however the local SPO is consistent with the stress orientation expected for local microstructures such as layering, garnet stacks, or fine-grained internal fluid pathways. Locally, two different preferential orientations are observed, interpreted as the result of two subsequent deformation stages under different stress configurations.</p><p>Quartz inclusions in prograde euhedral garnet, grown on the outer margin of coevally deformed garnetite, were analysed with Raman spectroscopy. Elastic strains obtained for these inclusions are in agreement with predicted strains for entrapment along the prograde <em>P</em>-<em>T</em> path for the Lago di Cignana unit (~1.5–2.0 GPa; ~450–500 °C), whereas significant differential stress during entrapment is expected to result in deviating strain components.</p><p>By combining microstructural analysis of garnet with elastic-strain analysis of quartz inclusions, stress orientations obtained from deformed garnet are combined with the stress magnitude for coeval garnet growth. The results indicate that the garnetite lenses were deformed and metamorphosed under low differential stress of variable orientation during subduction. These results are in agreement with a system where garnet is wet by a fluid phase that allows IPS.</p><p> </p><p>Acknowledgements: This project has received funding from the European Research Council under the H2020 research and innovation program (N. 714936 TRUE DEPTHS to M. Alvaro)</p>

The effect of elastic strains on the adsorption energy of H, O, and OH in transition metals

The adsorption energies of H, O, and OH on 11 transition metals were calculated as a function of strain. They were related to the Fermi energy level which only depended on the change of the area of the hole due to strain following a general law.