Specular neutron reflection at the mica/water interface – irreversible adsorption of a cationic dichain surfactant

2014 ◽  
Vol 47 (5) ◽  
pp. 1638-1646 ◽  
Author(s):  
Kathryn Louise Browning ◽  
Lucy Rachael Griffin ◽  
Philipp Gutfreund ◽  
Robert David Barker ◽  
Luke Ashley Clifton ◽  
...  

Neutron reflection from the important mineral mica at the solid/liquid interface is presented here using a new approach – a very thin mica crystal supported on a silicon substrate. This approach avoids the problems of crystal defects and surface undulations that have hindered previous work. The use of mica as a reflectivity substrate is important as it is a model surface, which is atomically smooth with a high structural charge. In this work the mica/water interface is fully characterized. In particular, a characteristic double critical edge is observed, arising from the higher scattering length densities of the mica and D2O subphase relative to the silicon support. The experimental data are modelled using a combined approach: conventional amplitude summation (matrix method) for the thin layers and reflected intensity summation with attenuation terms for the thick layers of mica and hydrocarbon adhesive. Reflection data from the adsorption of the dichain cationic surfactant didodecyldimethylammonium bromide (DDAB) to the surface of muscovite mica from aqueous solution are also presented. It is found that, at twice the critical micelle concentration, a bilayer of DDAB with a thickness of 24 Å is observed, containing essentially no water. Its partial removal by washing and ion exchange is also presented.

1996 ◽  
Vol 464 ◽  
Author(s):  
U. Sawhney ◽  
C.J. Durning ◽  
B. O'Shaughnessy ◽  
G.S. Smith ◽  
J. Majewski

ABSTRACTWe studied the equilibrium architecture of polymer layers strongly adsorbed from the melt. Immobilized layers of poly-(methyl methacrylate) (PMMA) were produced by the following method: 1) The polymer was spin-coated onto silanol bearing surfaces of single crystal and fused quartz, and annealed at melt conditions, 2) The annealed layer was quenched to room temperature (below the glass transition temperature) in order to “freeze in” the melt structure near the substrate, 3) Unbound material was leached away in good solvent (benzene) to leave a residual, strongly-adsorbed layer. The architecture of this layer was studied by neutron reflection. Data on dried adsorbed layers indicates a dense PMMA film whose thickness gradually increases with annealing time in the melt from a minimal value. Evidently, annealing gradually relaxes a rather flat non-equilibrium structure produced by spin-coating. The thicknesses, h, in a series of dry layers annealed long enough to achieve equilibrium conditions in the melt scale as h ∼ N1/2. Data on swollen layers suggest a dilute, extended layer, but the preliminary results cannot give a definitive confirmation of the brush structure predicted by Guiselin.11


1999 ◽  
Vol 39 (7) ◽  
pp. 91-98 ◽  
Author(s):  
Ryan N. Jordan ◽  
Eric P. Nichols ◽  
Alfred B. Cunningham

Bioavailability is herein defined as the accessibility of a substrate by a microorganism. Further, bioavailability is governed by (1) the substrate concentration that the cell membrane “sees,” (i.e., the “directly bioavailable” pool) as well as (2) the rate of mass transfer from potentially bioavailable (e.g., nonaqueous) phases to the directly bioavailable (e.g., aqueous) phase. Mechanisms by which sorbed (bio)surfactants influence these two processes are discussed. We propose the hypothesis that the sorption of (bio)surfactants at the solid-liquid interface is partially responsible for the increased bioavailability of surface-bound nutrients, and offer this as a basis for suggesting the development of engineered in-situ bioremediation technologies that take advantage of low (bio)surfactant concentrations. In addition, other industrial systems where bioavailability phenomena should be considered are addressed.


1997 ◽  
Vol 101 (49) ◽  
pp. 10332-10339 ◽  
Author(s):  
J. R. Lu ◽  
T. J. Su ◽  
Z. X. Li ◽  
R. K. Thomas ◽  
E. J. Staples ◽  
...  

1989 ◽  
Vol 166 ◽  
Author(s):  
B. Farnoux

ABSTRACTSeveral phenomena analogous to those observed in classical optics, such as reflection, refraction and interference, are also observed with slow neutrons. Information on surface properties, described by a refractive index profile, can be extracted from reflection experiments. This information is similar to that obtained by X-ray reflection. However, there are some instances where the new neutron method provides a distinct advantage. The refractive index is related to the scattering length density, a parameter which describes the neutron-matter interaction. Owing to the magnetic interaction, magnetic materials have a neutron spin dependent refractive index, and a critical reflection of polarized neutrons is a particularly sensitive probe of surface magnetism. On the other hand, in contrast to X-rays, neutron scattering length values vary randomly from element to element. Isotopic substitution can then produce a contrast in the scattering length density. Of particular importance is the large difference between hydrogen and deuterium. This is a distinct advantage for studiyng many problems in surface chemistry, particularly in the polymer field.


Sign in / Sign up

Export Citation Format

Share Document