Computational analysis of convective heat transfer properties of turbulent slot jet impingement

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Anuj Kumar Shukla ◽  
Anupam Dewan
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
High Efficiency ◽  
Stokes Equations ◽  
Turbulence Models ◽  
Jet Impingement ◽  
Complex Flow ◽  
Content Type

Purpose Convective heat transfer features of a turbulent slot jet impingement are comprehensively studied using two different computational approaches, namely, URANS (unsteady Reynolds-averaged Navier–Stokes equations) and SAS (scale-adaptive simulation). Turbulent slot jet impingement heat transfer is used where a considerable heat transfer enhancement is required, and computationally, it is a quite challenging flow configuration. Design/methodology/approach Customized OpenFOAM 4.1, an open-access computational fluid dynamics (CFD) code, is used for SAS (SST-SAS k-ω) and URANS (standard k-ε and SST k-ω) computations. A low-Re version of the standard k-ε model is used, and other models are formulated for good wall-refined calculations. Three turbulence models are formulated in OpenFOAM 4.1 with second-order accurate discretization schemes. Findings It is observed that the profiles of the streamwise turbulence are under-predicted at all the streamwise locations by SST k-ω and SST SAS k-ω models, but follow similar trends as in the reported results. The standard k-ε model shows improvements in the predictions of the streamwise turbulence and mean streamwise velocity profiles in the zone of outer wall jet. Computed profiles of Nusselt number by SST k-ω and SST-SAS k-ω models are nearly identical and match well with the reported experimental results. However, the standard k-ε model does not provide a reasonable profile or quantification of the local Nusselt number. Originality/value Hybrid turbulence model is suitable for efficient CFD computations for the complex flow problems. This paper deals with a detailed comparison of the SAS model with URANS and LES for the first time in the literature. A thorough assessment of the computations is performed against the results reported using experimental and large eddy simulations techniques followed by a detailed discussion on flow physics. The present results are beneficial for scientists working with hybrid turbulence models and in industries working with high-efficiency cooling/heating system computations.

Cooling of an isothermal surface having a cavity component by using CuO-water nano-jet

2019 ◽  
Vol 30 (4) ◽  
pp. 2169-2191 ◽  
Author(s):  
Fatih Selimefendigil ◽  
Ali J. Chamkha
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Fluid Flow ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Average Nusselt Number ◽  
Jet Impingement ◽  
Content Type ◽  
Impingement Cooling ◽  
Isothermal Surface

Purpose The purpose of this study is to numerically analyze the convective heat transfer features for cooling of an isothermal surface with a cavity-like portion by using CuO-water nano jet. Jet impingement cooling of curved surfaces plays an important role in practical applications. As compared to flat surfaces, fluid flow and convective heat transfer features with jet impingement cooling of a curved surface becomes more complex with additional formation of the vortices and their interaction in the jet wall region. As flow separation and reattachment may appear in a wide range of thermal engineering applications such as electronic cooling, combustors and solar power, jet impingement cooling of a surface which has a geometry with potential separation regions is important from the practical point of view. Design/methodology/approach Numerical simulations were performed with a finite volume-based solver. The study was performed for various values of the Reynolds number (between 100 and 400), length of the cavity (between 5 w and 40 w), height of the cavity (between w and 5w) and solid nano-particle volume fraction (between 0 and 4 per cent). Artificial neural network modeling was used to obtain a correlation for the average Nusselt number, which can be used to obtain fast and accurate predictions. Findings It was observed that cavity geometrical parameters of the cooling surface can be adjusted to change the flow field and convective heat transfer features. When the cavity length is low, significant contribution of the inclined wall of the cavity on the average Nusselt number is achieved. As the cavity length and height increase, the average Nusselt number, respectively, reduce and slightly enhance. At the highest value of cavity height, significant changes in the convective flow features are obtained. By using nanofluids instead of water, enhancement of average heat transfer in the range of 35-46 per cent is obtained at the highest particle volume fraction. Originality/value In this study, jet impingement cooling of an isothermal surface which has a cavity-like portion was considered with nanofluids. Addition of this portion to the impingement surface has the potential to produce additional vortices which affects the fluid flow and convective features in the jet impingement heat transfer. This geometry has the forward-facing step for the wall jet region with flow separation reattachment in the region. Based on the above literature survey and to the best of the authors’ knowledge, jet impingement cooling for such a geometry has never been reported in the literature despite its importance in practical thermal engineering applications. The results of this study may be useful for design and optimization of such systems and to obtain best performance in terms of fluid flow and heat transfer characteristics.

Numerical Analysis of a Multiple Jet Impingement System

2009 ◽  
Author(s):  
G. Arvind Rao ◽  
Myra Kitron-Belinkov ◽  
Yeshayahou Levy
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Flow Behavior ◽  
Flow Characteristics ◽  
Turbulence Models ◽  
Jet Impingement ◽  
Impinging Jets ◽  
Turbulent Regime ◽  
Transfer Coefficients ◽  
Complex Flow

Jet impingement is known to provide higher heat transfer coefficients as compared to other conventional modes of single phase heat transfer. Jet impingement has been a subject of research for a long time. Single jets have been studied extensively for their heat transfer and flow characteristics. However, for practical usage, multiple jets (in the form of arrays) have to be used for increasing the total heat transfer over a given area. Most of the research on multiple impinging jets have focused on evaluating heat transfer correlations for such arrays in the turbulent regime (Re >2500). The focus of the present paper is on experimental investigation of a large array of impinging jets in the low Reynolds number regime (<1000) and subsequently numerically modeling the same array by using existing Computational Fluid Dynamics tools in order to study the physical phenomena within such a complex system. Different turbulence models were used for modeling the fluid flow within these impinging jets and it was found that the SST k-ω model is the most suitable. Results obtained from CFD analysis are in reasonable agreement with experimental values. It was observed that CFD simulations over predicted the Nusselt number and pressure drop when compared to the experimentally obtained values. It was also observed that the decrease in Nusselt number along the streamwise direction of the array was not monotonic. This could be due to the complex flow field resulting from interaction between the crossflow and the impinging jets in the wall jet region. It is anticipated that results obtained from the present work will provide greater insight into the flow behavior and the heat transfer mechanism occurring in multiple impinging jets.

Three-dimensional combined radiation-magnetoconvection of low electrically conductive dielectric oxide melt

2019 ◽  
Vol 29 (10) ◽  
pp. 3611-3637 ◽  
Author(s):  
Abdullah A.A.A. Al-Rashed ◽  
Lioua Kolsi ◽  
Mohammed A. Tashkandi ◽  
Emad Hasani Malekshah ◽  
Ali J. Chamkha ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Electrically Conductive ◽  
Content Type ◽  
Oxide Melt

Purpose The purpose of this paper is to investigate the coupled effect of magnetic field and radiation on convective heat transfer of low electrically conductive dielectric oxide melt. Design/methodology/approach The 3D Navier–Stokes equations are formulated using the vector potential-vorticity formulation and solved using the finite volume method (FVM). The radiative heat transfer equation is discretized using the FTnFVM method. A code was written using FORTRAN language. Findings The obtained numerical results are focused on the effect of the different parameters on the heat transfer and the flow structure with a special interest on the 3D transvers flow. It is found that the flow is developing in inner spirals and the magnetic field intensifies this 3D character. The radiation acts mainly at the core of the enclosure and causes the apparition of the merging phenomenon near the front and back walls. Originality/value The effect of magnetic field on convective heat transfer of highly electrically conductive fluids has been intensively studied. Reciprocally, the case of a fluid with low electrical conductivity is not so much investigated, especially when it is coupled with the effect of radiation. These two effects are studied in this paper for the case of a low-conductive LiNbO3 oxide melt.

Assessment of Heat Transfer Enhancement Using Metallic Porous Foam Configurations in Laminar Slot Jet Impingement: An Experimental Study

2017 ◽  
Vol 140 (2) ◽  
Author(s):  
Chinige Sampath Kumar ◽  
Arvind Pattamatta
Keyword(s):  
Heat Transfer ◽  
Porous Media ◽  
Nusselt Number ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Average Nusselt Number ◽  
Heat Transfer Performance ◽  
Jet Impingement ◽  
Reynolds Numbers ◽  
Transfer Enhancement

An experimental study using the liquid crystal thermography technique is conducted to investigate the convective heat transfer performance in jet impingement cooling using various porous media configurations. Aluminum porous foams are used in the present study. Four impinging jet configurations are considered: jet impingement (1) without porous media, (2) over the porous heat sink, (3) with porous obstacle case, and (4) through porous passage. These configurations are evaluated on the basis of the convective heat transfer enhancement for two different Reynolds numbers of 400 and 700. Jet impingement with porous heat sink showed deterioration in the average Nusselt number by 9.95% and 18.04% compared to jet impingement without porous media configuration for Reynolds numbers of 400 and 700, respectively. Jet impingement with porous obstacles showed a very negligible enhancement in the average Nusselt number by 3.48% and 2.73% for Reynolds numbers of 400 and 700, respectively. However, jet impingement through porous passage configuration showed a maximum enhancement in the average Nusselt number by 52.71% and 74.68% and stagnation Nusselt numbers by 58.08% and 53.80% compared to the jet impingement without porous medium for Reynolds numbers of 400 and 700, respectively. Within the porous properties considered, it is observed that by decreasing the permeability and porosity the convective heat transfer performance tends to increase.

On Convective Heat Transfer and Flow Dynamics Through a Straight T-Bifurcating Channel

2017 ◽  
Vol 140 (3) ◽  
Author(s):  
Lakehal Abdelhak ◽  
Nait-Bouda Nora ◽  
Pelle Julien ◽  
Harmand Souad
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Stokes Equations ◽  
Dynamical Behavior ◽  
Symmetry Plane ◽  
Internal Surface ◽  
Local Heat Transfer ◽  
Flow Dynamics

Both experimental and numerical studies of a turbulent flow in a bifurcating channel are performed to characterize the dynamical behavior of the flow and its impact on the convective heat transfer on the sides of the branch. This configuration corresponds to the radial vents placed in the stator vertically to the rotor–stator air gap in the electrical machines. Indeed, our analysis focuses on the local convective heat transfer on the vents internal surface under a turbulent mass flow rate. The flow field measurements were carried out with two components particle image velocimetry (PIV) system, and the local heat transfer on the sides of the bifurcation branch was measured using an infrared thermography device. The convective heat transfer and the flow dynamics through the geometry are investigated numerically considering a three-dimensional (3D) flow. The closure system of the Navier–Stokes equations for steady and incompressible flow is based on the low-Reynolds numbers Reynolds stress model (RSM) (RSM-stress-ω). The comparison of the 3D computed results with the measurements in the xy symmetry plane is satisfactory in the vertical and horizontal channels. The numerical prediction of the secondary flow in the vertical branch was analyzed and complements the experimental results. It was particularly noticed that the accelerated flow observed at the right side of the branch's inlet allows more pronounced heat transfer comparatively to the left side. Beyond approximately 7 hydraulic diameters from the entrance of the branch, the Nusselt number curves on the two sides of the branch tend to be the same developed Nusselt number, Nud.

Convective Heat Transfer From a Heated Plate to the Orthogonally Impinging Air Jet

2016 ◽  
Vol 8 (4) ◽  
Author(s):  
Abhishek B. Bhagwat ◽  
Arunkumar Sridharan
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Jet Impingement ◽  
Secondary Peak ◽  
Plate Spacing ◽  
Air Jet ◽  
Plate Distance

The convective heat transfer process between the orthogonal air jet impingement on a uniformly heated flat plate is studied numerically. In this numerical study, three-dimensional (3D) simulations are carried out in Fluent 14.0 to investigate the effect of Reynolds number, distance between nozzle exit and the plate on the heat transfer characteristics. V2F turbulence model has been used to model turbulence. Standard κ–ε, Realizable κ–ε, κ–ε RNG, SST κ–ω, Standard κ–ω, V2F turbulence models have been studied for orthogonal jet impingement in this work. It is observed that for jet exit to plate distance (Z/d) of 0.5 ≤ Z/d ≤ 6, V2F model is best suited. For Z/d ≤ 0.5 and Z/d ≥ 6, numerical results vary significantly from the experimental results. Reynolds number of 12,000, 20,000, and 28,000 has been studied. In this paper, results for various jet exit to the plate distance (Z/d) from 0.5 to 10 are presented. At low jet plate spacing Z/d < 4, secondary peak in Nusselt number distribution over the plate is visible in experimental results. V2F model correctly predicts the secondary peak in Nusselt number variation over the plate. Other models fail to predict the secondary peak which is of significant importance in air jet impingement at low jet-plate spacing (Z/d < 4).

A computational analysis on convective heat transfer for impinging slot nanojets onto a moving hot body

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Hakan Coşanay ◽  
Hakan F. Oztop ◽  
Fatih Selimefendigil
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Unsteady Flow ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Computational Analysis ◽  
Impinging Jets ◽  
Content Type ◽  
Moving Body ◽  
Flow Effects

Purpose The purpose of this study is to perform computational analysis on the steady flow and heat transfer due to a slot nanojet impingement onto a heated moving body. The object is moving at constant speed and nanoparticle is included in the heat transfer fluid. The unsteady flow effects and interactions of multiple impinging jets are also considered. Design/methodology/approach The finite volume method was used as the solver in the numerical simulation. The movement of the hot body in the channel is also considered. Influence of various pertinent parameters such as Reynolds number, jet to target surface spacing and solid nanoparticle volume fraction on the convective heat transfer characteristics are numerically studied in the transient regime. Findings It is found that the flow field and heat transfer becomes very complicated due to the interaction of multiple impinging jets with the movement of the hot body in the channel. Higher heat transfer rates are achieved with higher values of Reynolds number while the inclusion of nanoparticles resulted in a small impact on flow friction. The middle jet was found to play an important role in the heat transfer behavior while jet and moving body temperatures become equal after t = 80. Originality/value Even though some studies exist for the application of jet impingement heat transfer for a moving plate, the configuration with a solid moving hot body on a moving belt under the impacts of unsteady flow effects and interactions of multiple impinging jets have never been considered. The results of the present study will be helpful in the design and optimization of various systems related to convective drying of products, metal processing industry, thermal management in electronic cooling and many other systems.

scholarly journals A numerical study of free convective heat transfer within domed skylight cavities

2021 ◽  
Author(s):  
AmirAbbas Sartipi
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Numerical Study ◽  
Control Volume ◽  
Energy Performance ◽  
Vortex Cell ◽  
Design Elements ◽  
Gap Ratio

Domed skylights are important architectural design elements to deliver daylight and solar heat into buildings and connect buildings' occupants to outdoors. To increase the energy efficiency of skylighted buildings, domed skylights employ a number of glazing layers forming enclosed spaces. The latter are subject to complex buoyancy-induced convection heat transfer. Currently, existing fenestration design computer tools and building energy simulation programs do not, however, cover such skylights to quantify their energy performance when installed in buildings. his work presents a numerical study on natural laminar convection within concentric and vertically eccentric domed cavities. The edges of domed cavities are assumed adiabatic and the temperature of the interior and exterior surfaces are uniform and constant. The concentric and vertically eccentric domed cavities were studied when heated from inside and heated from outside, respectively. A commercial CFD package employing the control volume approach is used to solve the laminar convective heat transfer within the cavity. The obtained results showed steady flow for small Grashof numbers. For moderate and large Grashof numbers, depending on the gap ratio and the cases of heating from inside or outside, the flow may be steady or transient periodic with a single vortex-cell or multi vortex-cells. The Nusselt number for the case of heated from inside is greater than the case of heated from outside. The numerical results show that the changes in the gap ratio have smaller effect on Nusselt number in high profile domed skylights than lower profile domed skylights.

Sign in / Sign up

Export Citation Format

Share Document