Experimental study of starvation in grease-lubricated finite line contacts

2017 ◽  
Vol 69 (6) ◽  
pp. 963-969 ◽  
Author(s):  
Zhijian Wang ◽  
Xuejin Shen ◽  
Xiaoyang Chen ◽  
Qiang Han ◽  
Lei Shi
Keyword(s):  
Film Thickness ◽  
High Viscosity ◽  
Operating Conditions ◽  
Test Rig ◽  
Oil Viscosity ◽  
Content Type ◽  
Base Oil ◽  
Optical Test ◽  
Line Contacts ◽  
Finite Line

Purpose The purpose of this paper is to study starvation in grease-lubricated finite line contacts and to understand film-forming mechanisms of grease-lubricated finite line contacts. Design/methodology/approach A multiple-contact optical elastohydrodynamic (EHL) test rig is constructed to investigate the influences of lubricant properties on film thickness and lubrication conditions at different working conditions. The film thickness is calculated according to the relative light intensity principle. The degree of starvation is evaluated by the air–oil meniscus distance and the corresponding film thickness. Findings The experimental results show that for greases with high-viscosity base oil, the high-frequency fluctuation of film thickness is observed in low-speed operating conditions. Reducing the viscosity of the base oil and improving running speed can weaken the fluctuation of film thickness. The degree of starvation increases with increasing base oil viscosity, rolling speed and the crown drop. In addition, reducing the replenishment time by reducing the gap between the rollers also can increase the degree of starvation. Originality/value Starvation is often to occur in finite line contacts, such as roller bearings and gears; there are still limited finite line contact EHL test rigs, much less multiple-contact optical test rigs. Therefore, the present work is undertaken to construct the multiple-contact test rig and to evaluate the mechanism of starvation in finite line contacts.

Elastohydrodynamic lubrication of coated finite line contacts

2017 ◽  
Vol 232 (9) ◽  
pp. 1077-1092 ◽  
Author(s):  
Shivam S Alakhramsing ◽  
Matthijn B de Rooij ◽  
Dirk J Schipper ◽  
Mark van Drogen
Keyword(s):  
Mechanical Properties ◽  
Film Thickness ◽  
Surface Profile ◽  
Elastohydrodynamic Lubrication ◽  
Operating Conditions ◽  
Maximum Pressure ◽  
Lubrication Performance ◽  
Line Contacts ◽  
Finite Line ◽  
Axial Surface

In this work, a finite element-based model is presented that simulates elastohydrodynamic lubrication in coated finite line contacts. Using this model, the film thickness and pressure distributions, between a straight roller with rounded edges on a plate, were analyzed. The model was successfully validated against representative results reported in literature. Parameter studies were conducted to study the influence of varying operating conditions, axial surface profile parameters and coating mechanical properties on the overall elastohydrodynamic lubrication behavior of the contact. It was found that in contrast with typical elastohydrodynamic lubrication behavior, the maximum pressure and minimum film thickness, which are located at the rear of the contact, are largely influenced by variations in load. Results also reveal that axial surface profile parameters and coating mechanical properties may act as amplifiers to the effect of load on pressure and film thickness distribution and can thus, if smartly chosen, significantly enhance lubrication performance.

Lubrication characteristics of the worn slipper in the slipper-swashplate pair

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Haiji Wang ◽  
Guanglin Shi
Keyword(s):  
Surface Roughness ◽  
Film Thickness ◽  
Design Methodology ◽  
Reynolds Equation ◽  
Thickness Distribution ◽  
Operating Conditions ◽  
Test Rig ◽  
Content Type ◽  
Oil Film ◽  
Lubrication Characteristics

Purpose This paper proposes the lubrication characteristics of the worn slipper in the slipper–swashplate pair. The mathematical analysis of lubrication characteristics of slipper with the measured surface roughness distribution is introduced. Based on the results from the test rig, it carries out the result compassion in different operating conditions. Design/methodology/approach This paper introduces the measured surface roughness distribution of new and used slippers and generates the oil film thickness distribution with it. An average flow Reynolds equation of the pressure distribution is introduced too. The experimental results are carried out on a novel adjustable oil film thickness test rig. Findings The surface roughness of the worn slipper enlarges the reacting force and torque only if the oil film thickness is small. When the ratio of oil film thickness to the root mean square of surface roughness is much smaller than 3, the influence of it on torque is obvious. Originality/value Different surface roughness of worn slipper proposed in this paper has an influence on the lubrication characteristics. As the slipper is worn after a period of use, the changed lubrication characteristics should be considered in the slipper design.

A thermal EHL investigation for size effect of finite line contact on bush-pin hinge pairs in industrial chains

2020 ◽  
Vol 72 (5) ◽  
pp. 695-701
Author(s):  
Mingyu Zhang ◽  
Jing Wang ◽  
Peiran Yang ◽  
Zhaohua Shang ◽  
Yi Liu ◽  
...  
Keyword(s):  
Film Thickness ◽  
Peer Review ◽  
Contact Zone ◽  
Line Contact ◽  
Equivalent Radius ◽  
Content Type ◽  
Oil Film ◽  
Finite Line Contact ◽  
Finite Line ◽  
Thermal Ehl

Purpose This paper aims to study the influence of the dimension change of bush-pin on the pressure, oil film thickness, temperature rise and traction coefficient in contact zone by using a thermal elastohydrodynamic lubrication (EHL) model for finite line contact. Concretely, the effects of the equivalent curvature radius of the bush and the pin, and the length of the bush are investigated. Design/methodology/approach In this paper, the contact between the bush and pin is simplified as finite line contact. The lubrication state is studied by numerical simulation using steady-state line contact thermal EHL. A constitutive equation Ree–Eyring fluid is used in the calculations. Findings It is found that by selecting an optimal equivalent radius of curvature and prolonging the bush length can improve the lubrication state effectively. Originality/value Under specific working conditions, there exists an optimal equivalent radius to maximize the minimum oil film thickness in the contact zone. The increase of generatrix length will weaken the stress concentration effect in the rounded corner area at both ends of the bush, which can improve the wear resistance of chain. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-10-2019-0448.

An adjustable oil film thickness test rig for detecting lubrication characteristics of slipper/swash-pair in piston pumps

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Haiji Wang ◽  
Guanglin Shi
Keyword(s):  
Film Thickness ◽  
Peer Review ◽  
Relative Error ◽  
Mathematical Analysis ◽  
Test Rig ◽  
Content Type ◽  
Oil Film ◽  
Displacement Sensors ◽  
Measuring Machine ◽  
Lubrication Characteristics

Purpose The purpose of this paper is to propose an adjustable oil film thickness test rig for detecting lubrication characteristics of the slipper. The mathematical analysis of lubrication is introduced. Based on the results from the test rig, the results comparison from test rig and mathematical analysis is carried out. Design/methodology/approach This paper introduces a mechanism which can adjust the oil film thickness between the slipper and swash-plate. Feasibility is ensured, and the accuracy of test rig is guaranteed by the three-coordinate measuring machine. Three displacement sensors show the oil film thickness and its shape. The reacting force and torque resulting from oil film can be achieved by three S-type force sensors and a torque sensor, respectively. Findings The relative error of the reacting force is small. The relative error reduces and is acceptable when the deformation of retainer is taken into account. The thickness and tilt angle of oil film have less effect on the reacting force. However, they are significantly impact on torque. Originality/value The test rig proposed in this paper is able to adjust the oil film thickness, which is used to detecting the lubrication characteristics in pump design. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-05-2020-0166/

A thermal EHL investigation on plate-pin hinge pairs in silent chains using a narrow finite line contact

2020 ◽  
Vol 72 (10) ◽  
pp. 1139-1145
Author(s):  
Mingyu Zhang ◽  
Jing Wang ◽  
Jinlei Cui ◽  
Peiran Yang
Keyword(s):  
Film Thickness ◽  
Temperature Rise ◽  
Elastohydrodynamic Lubrication ◽  
Radius Of Curvature ◽  
Line Contact ◽  
Equivalent Radius ◽  
Content Type ◽  
Finite Line Contact ◽  
Pressure Peak ◽  
Finite Line

Purpose The purpose of this paper is to numerically study the variations of oil film pressure, thickness and temperature rise in the contact zone of plate-pin pair in silent chains. Design/methodology/approach A steady-state thermal elastohydrodynamic lubrication (EHL) model is built using a Ree–Eyring fluid. The contact between the plate and the pin is simplified as a narrow finite line contact, and the lubrication state is examined by varying the geometry and the plate speed. Findings With increase in the equivalent radius of curvature, the pressure peak and the central film thickness increase. Because the plate is very thin, the temperature rise can be neglected. Even when the influence of the rounded corner region is less, a proper design can beneficially increase the minimum film thickness at both edges of the plate. Under a low entraining speed, strong stress concentration results in close-zero film thickness at both edges of the plate. Originality/value This study reveals the EHL feature of the narrow finite line contact in plate-pin pairs for silent chains and will support the future works considering transient effect, surface features and wear.

Effects of a thickener structure on grease elastohydrodynamic lubrication films

2000 ◽  
Vol 214 (4) ◽  
pp. 327-336 ◽  
Author(s):  
M Kaneta ◽  
T Ogata ◽  
Y Takubo ◽  
M Naka
Keyword(s):  
Film Thickness ◽  
Direct Observation ◽  
Film Formation ◽  
Elastohydrodynamic Lubrication ◽  
Rolling Speed ◽  
Molecular Structures ◽  
Optimum Temperature ◽  
Oil Viscosity ◽  
Base Oil ◽  
Different Types

The effects of the thickener structure and base oil viscosity on the grease film formation in rolling point elastohydrodynamic contacts have been discussed on the basis of direct observation using the optical interferometry technique. Three different types of diurea greases without additives have been used as test greases. As the base oils three kinds of ether-type synthetic oils having similar molecular structures but different viscosities were used. The film behaviour of fresh greases has also been compared with that of the degraded greases. It has been found that the behaviour of grease elastohydrodynamic lubrication films is basically influenced by the thickener structure and base oil viscosity. The adhesion or deposition of the thickener on the contacting surfaces and oil starvation which affect film formation depend on the thickener structure, base oil viscosity and rolling speed. Furthermore, it has been suggested that there is an optimum temperature which gives a maximum film thickness according to the consistency of the grease.

Multiobjective optimization of journal bearing using mass conserving and genetic algorithms

2005 ◽  
Vol 219 (3) ◽  
pp. 235-248 ◽  
Author(s):  
H Hirani
Keyword(s):  
Thermal Analysis ◽  
Genetic Algorithms ◽  
Film Thickness ◽  
Journal Bearing ◽  
Operating Conditions ◽  
Radial Clearance ◽  
Pareto Optimal ◽  
Optimization Strategy ◽  
Oil Viscosity ◽  
Film Pressure

An optimal design of hydrodynamic journal bearing using mass conserving thermal analysis and genetic algorithms is presented. Simultaneous minimization of power loss and oil flow, subjected to constraints on film thickness, film pressure, and temperature rise between the bearing surfaces, is the objective of this study. The radial clearance, L/D ratio, oil groove location, feed pressure, and the oil viscosity are the design variables. The rank-based genetic algorithm is used to deal with the discrete variables and multimodal objective functions and to capture Pareto optimal points. In view of computation economics and robustness, initial guesses of oil film pressure distribution, eccentricity ratio, and attitude angle obtained by two-dimensional analytical approach are provided for mass conserving thermal analysis. The complete optimization strategy is illustrated by a step-by-step (in four steps) approach. A comparative study of thermal and isothermal analyses is illustrated. Effects of constraints on temperature, pressure, and film thickness on the design vector are enlightened. The mass conserving thermal analysis is validated against experimental results. Pareto optimal fronts for various operating conditions are presented.

Influence of steadite on the tribological behavior of cylinder liners

2019 ◽  
Vol 71 (2) ◽  
pp. 324-332 ◽  
Author(s):  
Tiago Cousseau ◽  
Edison Serbino ◽  
Edney Rejowski ◽  
Amilton Sinatora
Keyword(s):  
Friction And Wear ◽  
Piston Ring ◽  
Experimental Approach ◽  
Operating Conditions ◽  
Content Type ◽  
Base Oil ◽  
Real Area Of Contact ◽  
Eds Analysis ◽  
Cylinder Liners ◽  
Real Area

Purpose This paper aims to understand the effect of steadite in gray cast iron (GCI) cylinder liners performance (friction and wear) when lubricated with new lube oil formulations to verify if steadite can be reduced or suppressed from cylinder liners composition. Design/methodology/approach The paper presents an experimental approach to quantify the separated effect of lube additives and steadite content on GCI performance. Friction and wear of GCI samples with and without steadite were analyzed under lubricated conditions with a 5W30 lubricant and a base oil of similar viscosity under operating conditions similar to the ones observed at the top dead center of Otto engines. Scanning electron microscopy (SEM)-EDS analysis was used to evaluate wear and tribofilm formation. Findings The paper shows that steadite stabilizes friction coefficient and slightly reduces wear in the tests performed with base oil. However, its advantages are marginal in comparison to the ones provided by the fully formulated oil. Furthermore, SEM-EDS analyses of the wear track showed that steadite does not chemically react with zinc and sulfur compounds, reducing the tribofilm formation on the real area of contact and consequently changing the tribosystem behavior. Originality/value This paper covers an identified need to study the effect of lube additives and GCI composition using actual piston ring and cylinder liners under operating conditions similar to the ones observed at the top dead center of Otto engines.

Influence of Contact Pressure on Central and Minimum Film Thickness Within Ultrathin Film Lubricated Contacts

2005 ◽  
Vol 127 (4) ◽  
pp. 890-892 ◽  
Author(s):  
I. Křupka ◽  
M. Hartl ◽  
M. Liška
Keyword(s):  
Thin Film ◽  
Film Thickness ◽  
Nonlinear Behavior ◽  
Test Rig ◽  
Lubricated Contacts ◽  
Optical Test ◽  
Minimum Film Thickness ◽  
Lubricant Films ◽  
The Relationship ◽  
Contact Pressures

Recent numerical results have indicated that the relationship between the film thickness and the speed may not always follow the simple power law, especially under severe conditions. This paper is aimed at obtaining experimental results at high contact stresses and low speeds to study the thin film behavior. Ultrathin lubricant films were observed at maximum Hertz pressures of 0.52, 1.01, and 1.54 GPa by using an optical test rig. Central and minimum film thickness values were obtained with thin film colorimetric interferometry from chromatic interferograms. The nonlinear behavior of both central and minimum film thicknesses in log-log coordinates was observed as rolling speed and thereby film thickness decreased. This tendency became more obvious at higher contact pressures.

Lubrication Capacity of Gears of Circular-Arc Tooth-Profile

1988 ◽  
Vol 110 (4) ◽  
pp. 699-703 ◽  
Author(s):  
Awny Y. Attia ◽  
Ahmed M. M. El-Bahloul
Keyword(s):  
Film Thickness ◽  
Carrying Capacity ◽  
Helix Angle ◽  
Load Carrying Capacity ◽  
Test Rig ◽  
Oil Viscosity ◽  
Oil Film ◽  
Lubricant Oil ◽  
Linear Dimensions ◽  
Load Carrying

The paper presents the results of an experimental investigation carried out at Mansoura University Laboratories aiming at studying the effect of change of speed, oil viscosity, and helix angle on the load carrying capacity of the oil film. A three pairs of test gears of 6 DP, 91.5 mm pitch diameter with 22.3, 33.6 and 42.25 deg helix angles were run in power circulating test rig at 100 to 3000 r.p.m. speeds and transmitting tooth load ranging from 185 to 1090 Kp. The test gears were lubricated with oils of 200, 462, and 653 cSt at 40°C kinematic viscosities. The oil film thicknesses between contacting teeth were measured by measuring the changes in capacitance between test gears and transferred to linear dimensions by calibration curves drawn by knowing the changes in capacitance through the gaps between teeth of values known through the amount of backlash. The experimental results show that; Oil film thickness decreases with tooth load, while increases with speed and viscosity of the lubricant. Oil film thickness versus helix angle give an inversed parabola for the smallest and medium tooth loads, while oil film thickness decreases with increasing the helix angle under increased tooth loads. Load carrying capacity increases with speeds and viscosity of the lubricant while decreases with increasing the helix angle.

Sign in / Sign up

Export Citation Format

Share Document