R, G, B acquisition interface with line-locked clock generator for flat panel display

1998 ◽  
Vol 33 (7) ◽  
pp. 1009-1013 ◽  
Author(s):  
H. Marie ◽  
P. Belin
Keyword(s):  
Clock Generator ◽  
Flat Panel Display ◽  
Flat Panel

scholarly journals Integrated Active Microfluidics using Flat Panel Display Technology with Two Different Semiconductor Grade Polymers

2021 ◽  
Author(s):  
Boshen Liang ◽  
Grim Keulemans ◽  
Dominika Wysocka ◽  
Alexey Podkovskiy ◽  
Lei Zhang ◽  
...  
Keyword(s):  
Flat Panel Display ◽  
Flat Panel ◽  
Display Technology

scholarly journals Optimal Color Lighting for Scanning Images of Flat Panel Display using Simplex Search

2018 ◽  
Vol 4 (11) ◽  
pp. 133
Author(s):  
HyungTae Kim ◽  
EungJoo Ha ◽  
KyungChan Jin ◽  
ByungWook Kim
Keyword(s):  
Image Quality ◽  
Light Source ◽  
Light Emitting Diode ◽  
Optical Filters ◽  
Flat Panel Display ◽  
Flat Panel ◽  
Light Emitting ◽  
Simplex Search ◽  
Inspection Systems ◽  
Color Control

A system for inspecting flat panel displays (FPDs) acquires scanning images using multiline charge-coupled device (CCD) cameras and industrial machine vision. Optical filters are currently installed in front of these inspection systems to obtain high-quality images. However, the combination of optical filters required is determined manually and by using empirical methods; this is referred to as passive color control. In this study, active color control is proposed for inspecting FPDs. This inspection scheme requires the scanning of images, which is achieved using a mixed color light source and a mixing algorithm. The light source utilizes high-power light emitting diodes (LEDs) of multiple colors and a communication port to dim their level. Mixed light illuminates an active-matrix organic light-emitting diode (AMOLED) panel after passing through a beam expander and after being shaped into a line beam. The image quality is then evaluated using the Tenenbaum gradient after intensity calibration of the scanning images. The dimming levels are determined using the simplex search method which maximizes the image quality. The color of the light was varied after every scan of an AMOLED panel, and the variation was iterated until the image quality approached a local maximization. The number of scans performed was less than 225, while the number of dimming level combinations was 20484. The proposed method can reduce manual tasks in setting-up inspection machines, and hence is useful for the inspection machines in FPD processes.

Inverters Using Only N-Type Indium Gallium Zinc Oxide Thin Film Transistors for Flat Panel Display Applications

2011 ◽  
Vol 50 (3) ◽  
pp. 03CB06 ◽  
Author(s):  
Tong-Hun Hwang ◽  
Ik-Seok Yang ◽  
Oh-Kyong Kwon ◽  
Min-Ki Ryu ◽  
Choon-Won Byun ◽  
...  
Keyword(s):  
Thin Film ◽  
Zinc Oxide ◽  
Thin Film Transistors ◽  
Oxide Thin Film ◽  
Indium Gallium Zinc Oxide ◽  
Flat Panel Display ◽  
Zinc Oxide Thin Film ◽  
Flat Panel ◽  
Indium Gallium

Use of a Secondary Task Methodology for Determining Acceptability of Flat-Panel Display Technologies in Consumer Environments

1983 ◽  
Vol 27 (5) ◽  
pp. 344-348
Author(s):  
Mark S. Hoffman ◽  
Martin L. Cramer
Keyword(s):  
Behavioral Problems ◽  
Secondary Task ◽  
Cognitive Task ◽  
Experimental Methodology ◽  
Human Information Processing ◽  
Primary Concern ◽  
Flat Panel Display ◽  
Flat Panel ◽  
Cost Constraints ◽  
Ambient Lighting

Flat-panel displays are used in consumer environments for displaying information where limits on content, physical space, power, and cost constraints are critical. Applications have traditionally included Retail Point-of-Service (POS) terminals. Most common flat-panel display technologies found in the consumer markets are Liquid Crystal Displays (LCDs), Plasma, and Vacuum Fluorescent displays. Emitting displays, i.e., Vacuum Fluorescent, Plasma, and LEDs were introduced into the marketplace with few reservations as to their general acceptance since normal ambient lighting conditions other than direct sunlight had minimal impact on readability. However, reflective display technologies, i.e., LCDs have not been widely accepted in POS products because of slower response times and a more restrictive range of ambient light needed to achieve acceptable viewing conditions. Many techniques used for determining the acceptability of a display technology for the POS environment presently used in industry are solely based upon the physical and functional performance characteristics of the display itself. This approach is similar to those used for evaluating video displays in that the primary concern is the stability of the displayed output for the intended user environment. Often these evaluations are conducted in a laboratory and therefore do not compare display performances relative to the intended end user. Even though this approach is cost-effective because the physical attributes of the display can be tailored to maximize readability, it does not consider the effect of the displayed information beyond the properties of the human visual system. Therefore, it would be desirable to develop an experimental methodology for evaluating flat-panel display technologies based upon human information processing capabilities. This requires using the information in cognitive task loadings equivalent to those experienced in the user environment. Studies comparing LCDs and Plasma display technologies were designed to construct a cognitive-perceptual model for usability assessment in the retail POS environment. A secondary task methodology was used to predict mental workload associated with each display. A Choice Reaction Time (CRT) paradigm proved to be an effective method for exploring cognitive-behavioral problems associated with the displays beyond those considered in the traditional methods of display evaluation.

Sign in / Sign up

Export Citation Format

Share Document