Monolithic GaAs phase shifter circuit with low insertion loss and continuous 0-360° phase shift at 20 GHz

1999 ◽  
Vol 9 (1) ◽  
pp. 31-33 ◽  
Author(s):  
A.S. Nagra ◽  
Jian Xu ◽  
E. Erker ◽  
R.A. York
Circuit World ◽  
2018 ◽  
Vol 44 (3) ◽  
pp. 115-124 ◽  
Author(s):  
Prithivi Rajan V. ◽  
Punitha A.

Purpose This paper aims to design a radio frequency micro-electro-mechanical system (RF MEMS)-based phase shifter using chamfered coplanar waveguide (CPW) transmission line (t-line) with open-circuit interdigital metal–air–metal (ID MAM) capacitors. Design/methodology/approach The proposed phase shifter achieves maximum differential phase shift with low loss at Ku band. The phase shifter is built with one switchable fixed-fixed beam (MEMS switch) on chamfered CPW t-line in series with two planar open-circuit ID MAM capacitors. An equivalent circuit model for the proposed phase shifter is derived, and its parameters are extracted using an electromagnetic (EM) solver. Findings The MEMS switch is actuated using an electrostatic method with the calculated residual stress of 44.26 MPa. The fabricated phase shifter exhibits low insertion loss, close to 0.14 dB at 17 GHz, with the maximum phase shift of 15.06°. The return loss is greater than 23 dB between 12 and 18 GHz. Originality/value This phase shifter presents a promising solution for low loss applications in the Ku band with a maximum phase shift. As the maximum phase shift of 15.06° is achieved for a unit cell with low insertion loss, the phase shifter is found to be feasible for modern electronically tunable phased arrays used for satellite communication and radar systems.


Author(s):  
Aparna B. Barbadekar ◽  
Pradeep M. Patil

Abstract The paper proposes a system consisting of novel programmable system on chip (PSoC)-controlled phase shifters which in turn guides the beam of an antenna array attached to it. Four antennae forming an array receive individual inputs from the programmable phase shifters (IC 2484). The input to the PSoC-based phase shifter is provided from an optimized 1:4 Wilkinson power divider. The antenna consists of an inverted L-shaped dipole on the front and two mirrored inverted L-shaped dipoles mounted on a rectangular conductive structure on the back which resonates in the ISM/Wi-Fi band (2.40–2.48 GHz). The power divider is designed to provide the feed to the phase shifter using a beamforming network while ensuring good isolation among the ports. The power divider has measured S11, S21, S31, S41, and S51 to be −14, −6.25, −6.31, −6.28, and −6.31 dB, respectively at a frequency of 2.45 GHz. The ingenious controller is designed in-house using a PSoC microcontroller to regulate the control voltage of individual phase shifter IC and generate progressive phase shifts. To validate the calibration of the in-house designed control circuit, the phased array is simulated using $s_p^2$ touchstone file of IC 2484. This designed control circuit exhibits low insertion loss close to −8.5 dB, voltage standing wave ratio of 1.58:1, and reflection coefficient (S11) is −14.36 dB at 2.45 GHz. Low insertion loss variations confirm that the phased-array antenna gives equal amplitude and phase. The beamforming radiation patterns for different scan angles (30, 60, and 90°) for experimental and simulated phased-array antenna are matched accurately showing the accuracy of the control circuit designed. The average experimental and simulated gain is 13.03 and 13.48 dBi respectively. The in-house designed controller overcomes the primary limitations associated with the present electromechanical phased array such as cost weight, size, power consumption, and complexity in design which limits the use of a phased array to military applications only. The current study with novel design and enhanced performance makes the system worthy of the practical use of phased-array antennas for common society at large.


1999 ◽  
Vol 603 ◽  
Author(s):  
Amit S. Nagra ◽  
Troy R. Taylor ◽  
Padmini Periaswamy ◽  
James Speck ◽  
Robert A. York

AbstractPeriodically loaded line phase shifter circuits using voltage tunable BaSrTiO3 (BST) parallel plate capacitors have been demonstrated at X-band. The first such phase shifter circuit was capable of 100° of phase shift with an insertion loss of 7.6 dB at 10 GHz. Subsequently, the monolithic fabrication procedure was refined resulting in an improved phase shifter circuit with 200° of phase shift and an insertion loss of 6.2 dB at 10 GHz. In addition to promising loss performance (32°/dB) at 10 GHz, the circuits reported here have several desirable features such as moderate control voltages (20 V), room temperature operation, and compatibility with monolithic fabrication techniques.


2014 ◽  
Vol 35 (10) ◽  
pp. 105005 ◽  
Author(s):  
Mengyi Cao ◽  
Yang Lu ◽  
Jiaxing Wei ◽  
Jiaxin Zheng ◽  
Xiaohua Ma ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document