Phased-array antennas using novel PSoC-controlled phase shifters for wireless applications

Author(s):  
Aparna B. Barbadekar ◽  
Pradeep M. Patil

Abstract The paper proposes a system consisting of novel programmable system on chip (PSoC)-controlled phase shifters which in turn guides the beam of an antenna array attached to it. Four antennae forming an array receive individual inputs from the programmable phase shifters (IC 2484). The input to the PSoC-based phase shifter is provided from an optimized 1:4 Wilkinson power divider. The antenna consists of an inverted L-shaped dipole on the front and two mirrored inverted L-shaped dipoles mounted on a rectangular conductive structure on the back which resonates in the ISM/Wi-Fi band (2.40–2.48 GHz). The power divider is designed to provide the feed to the phase shifter using a beamforming network while ensuring good isolation among the ports. The power divider has measured S11, S21, S31, S41, and S51 to be −14, −6.25, −6.31, −6.28, and −6.31 dB, respectively at a frequency of 2.45 GHz. The ingenious controller is designed in-house using a PSoC microcontroller to regulate the control voltage of individual phase shifter IC and generate progressive phase shifts. To validate the calibration of the in-house designed control circuit, the phased array is simulated using $s_p^2$ touchstone file of IC 2484. This designed control circuit exhibits low insertion loss close to −8.5 dB, voltage standing wave ratio of 1.58:1, and reflection coefficient (S11) is −14.36 dB at 2.45 GHz. Low insertion loss variations confirm that the phased-array antenna gives equal amplitude and phase. The beamforming radiation patterns for different scan angles (30, 60, and 90°) for experimental and simulated phased-array antenna are matched accurately showing the accuracy of the control circuit designed. The average experimental and simulated gain is 13.03 and 13.48 dBi respectively. The in-house designed controller overcomes the primary limitations associated with the present electromechanical phased array such as cost weight, size, power consumption, and complexity in design which limits the use of a phased array to military applications only. The current study with novel design and enhanced performance makes the system worthy of the practical use of phased-array antennas for common society at large.

2002 ◽  
Vol 720 ◽  
Author(s):  
J. B. L. Rao ◽  
D. P. Patel ◽  
P. K. Park ◽  
T. K. Dougherty ◽  
J. A. Zelik ◽  
...  

AbstractA novel, low-cost, phased-array antenna that uniquely incorporates bulk phase shifting using voltage-tunable dielectric (VTD) material is presented. The array does not contain an individual phase shifter at each radiating element. This paper presents the antenna concept and describes how it can be used as a low-cost phased array. The VTDs that are used in this antenna are described. The measured antenna patterns of a prototype phased array demonstrating electronic beam scanning at 10 GHz are also presented.


2013 ◽  
Vol 5 (5) ◽  
pp. 629-636
Author(s):  
Wei Shi ◽  
Jun Zhou ◽  
Zuping Qian ◽  
Ya Shen

Detailed analysis of the polarization tracking modules for Ku band active phased array antennas is presented. The proposed transmitter (14.0–14.5 GHz) and receiver (12.25–12.75 GHz) modules are based on the low temperature co-fired ceramic (LTCC) technique, containing orthogonal dual channels with different phases controlled by phase shifters. The effect of amplitude and phase inconsistency between two channels on polarization tracking performance is analyzed. The validity of the analysis is verified by the measurements of the manufactured prototypes. The measured patterns of the active phased array antenna are given to illustrate the effects of the modules on polarization agility, which may be used for Ku band satellite antennas on mobile terminals.


2010 ◽  
Vol 2 (3-4) ◽  
pp. 263-271 ◽  
Author(s):  
P. Farinelli ◽  
S. Bastioli ◽  
E. Chiuppesi ◽  
F. Di Maggio ◽  
B. Margesin ◽  
...  

This work presents the design, manufacturing, and testing of three 5-bit K-band Micro-Electro-Mechanical-Systems (MEMS) phase shifters based on similar architectures (combination of switched line and loaded line) but employing different MEMS switch typologies (cantilevers and air bridges) and RF junctions (SP2T and SP4T). All devices have been monolithically manufactured on 200 µm thick high resistivity silicon substrate (4″) by using the Fondazione Bruno Kessler (FBK) RF MEMS process. The performance of the different devices has been compared in order to identify the best configuration to be implemented in electronically steerable phased array antennas for satellite COTM (communication on the move) terminals. Excellent performances were measured for the dielectric-free pad RF MEMS switches as well as the single bits constituting the phase shifter. The three 5-bit devices show return losses better than 15 dB for all states, with average insertion loss of 3.5 dB for the clamped–clamped, SP2T-based design, 2.2 dB for the cantilever, SP2T-based device and 2.1 dB for the cantilever, SP4 T-based design. A low-cost Surface Mountable Technology (SMT) one-level package has been developed as well to allow the phase shifter integration into phased array antennas by using automatic surface mounting techniques. The design and simulation of the SMT package are also presented together with its measured RF performance.


Author(s):  
Tarek Sallam ◽  
Ahmed M. Attiya

Abstract Achieving robust and fast two-dimensional adaptive beamforming of phased array antennas is a challenging problem due to its high-computational complexity. To address this problem, a deep-learning-based beamforming method is presented in this paper. In particular, the optimum weight vector is computed by modeling the problem as a convolutional neural network (CNN), which is trained with I/O pairs obtained from the optimum Wiener solution. In order to exhibit the robustness of the new technique, it is applied on an 8 × 8 phased array antenna and compared with a shallow (non-deep) neural network namely, radial basis function neural network. The results reveal that the CNN leads to nearly optimal Wiener weights even in the presence of array imperfections.


1995 ◽  
Vol 8 (1-2) ◽  
pp. 65-76 ◽  
Author(s):  
R. Babbitt ◽  
T. Koscica ◽  
W. Drach ◽  
L. Didomenico

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
ByungKuon Ahn ◽  
In-June Hwang ◽  
Kwang-Seok Kim ◽  
Soo-Chang Chae ◽  
Jong-Won Yu ◽  
...  

AbstractThis paper presents a wide-angle scanning phased array antenna using high gain pattern reconfigurable antenna (PRA) elements. Using PRA elements is an attractive solution for wide-angle scanning phased array antennas because the scanning range can be divided into several subspaces. To achieve the desired scanning performance, some characteristics of the PRA element such as the number of switching modes, tilt angle, and maximum half-power beamwidth (HPBW) are required. We analyzed the required characteristics of the PRA element according to the target scanning range and element spacing, and presented a PRA element design guideline for phased array antennas. In accordance with the guideline, the scanning range was set as ±70° and a high gain PRA element with three reconfigurable patterns was used to compose an 8x1 array antenna with 0.9 λ0 spacing. After analyzing whether the active element patterns meet the guideline, the array antenna was fabricated and measured to demonstrate the scanning performance. The fabricated array can scan its beam from -70° to 70° by dividing the scanning range into three subspaces. It shows that even if the array antenna has large element spacing, the desired scanning performance can be obtained using the elements designed under the guideline.


1999 ◽  
Vol 603 ◽  
Author(s):  
R. R. Romanofsky ◽  
F. W. Van Keuls ◽  
J. D. Warner ◽  
C. H. Mueller ◽  
S. A. Alterovitz ◽  
...  

AbstractMicrowave phase shifters have been fabricated from (YBa2Cu3 O7-δ or Au)/SrTiO3 and Au/BaxSr1−xTiO3 films on LaAlO3 and MgO substrates. These coupled microstrip devices rival the performance of their semiconductor counterparts at Ku- and K-band frequencies. Typical insertion loss for room temperature ferroelectric phase shifters at K-band is ≈5 dB. An experimental and theoretical investigation of these novel devices explains the role of the ferroelectric film in overall device performance. A roadmap to the development of a 3 dB insertion loss phase shifter that would enable a new type of phased array antenna is discussed.


Sign in / Sign up

Export Citation Format

Share Document