Hydrodynamic analysis of a gliding robotic dolphin based on Computational Fluid Dynamics

Author(s):  
Kang Li ◽  
Junzhi Yu ◽  
Zhengxing Wu ◽  
Min Tan
Fluids ◽  
2021 ◽  
Vol 6 (6) ◽  
pp. 204
Author(s):  
Kamran Fouladi ◽  
David J. Coughlin

This report presents the development of a fluid-structure interaction model using commercial Computational fluid dynamics software and in-house developed User Defined Function to simulate the motion of a trout Department of Mechanical Engineering, Widener University holding station in a moving water stream. The oscillation model used in this study is based on the observations of trout swimming in a respirometry tank in a laboratory experiment. The numerical simulations showed results that are consistent with laboratory observations of a trout holding station in the tank without obstruction and trout entrained to the side of the cylindrical obstruction. This paper will be helpful in the development of numerical models for the hydrodynamic analysis of bioinspired unmanned underwater vehicle systems.


2021 ◽  
Author(s):  
Ming Chen ◽  
Solomon Yim ◽  
Daniel Cox ◽  
Zhaoqing Yang ◽  
Thomas Mumford

2019 ◽  
Vol XXII (1) ◽  
pp. 220-230
Author(s):  
Gürsel K. T.

This study is related to the design features of pontoon boats that enjoy an increasing market share in global recreational boat industry. In this investigation, a representative pontoon boat with three cylindrical buoyancy elements was taken as the model to be studied. Afterwards, the buoyancy elements were improved to optimize hydrodynamic properties using a computational fluid dynamics package. The objective functions were the total hydrodynamic resistance of the boat and the distribution of the turbulence viscosity and total pressure on the hulls. By means of the obtained results, the powering requirements were estimated both for a service speed and for a maximum speed as well as findings were discussed.


Energies ◽  
2013 ◽  
Vol 6 (5) ◽  
pp. 2362-2385 ◽  
Author(s):  
Vincenzo Sammartano ◽  
Costanza Aricò ◽  
Armando Carravetta ◽  
Oreste Fecarotta ◽  
Tullio Tucciarelli

2014 ◽  
Vol 37 (3) ◽  
pp. 383-391 ◽  
Author(s):  
Jinsheng Sun ◽  
Xubo Luo ◽  
Shuo Jiang ◽  
Wenping Wang ◽  
Hao Lyu ◽  
...  

2015 ◽  
Vol 31 (1) ◽  
pp. 48-55 ◽  
Author(s):  
J. Paulo Vilas-Boas ◽  
Rui J. Ramos ◽  
Ricardo J. Fernandes ◽  
António J. Silva ◽  
Abel I. Rouboa ◽  
...  

The aim of this research was to numerically clarify the effect of finger spreading and thumb abduction on the hydrodynamic force generated by the hand and forearm during swimming. A computational fluid dynamics (CFD) analysis of a realistic hand and forearm model obtained using a computer tomography scanner was conducted. A mean flow speed of 2 m·s−1was used to analyze the possible combinations of three finger positions (grouped, partially spread, totally spread), three thumb positions (adducted, partially abducted, totally abducted), three angles of attack (a = 0°, 45°, 90°), and four sweepback angles (y = 0°, 90°, 180°, 270°) to yield a total of 108 simulated situations. The values of the drag coefficient were observed to increase with the angle of attack for all sweepback angles and finger and thumb positions. For y = 0° and 180°, the model with the thumb adducted and with the little finger spread presented higher drag coefficient values for a = 45° and 90°. Lift coefficient values were observed to be very low at a = 0° and 90° for all of the sweepback angles and finger and thumb positions studied, although very similar values are obtained at a = 45°. For y = 0° and 180°, the effect of finger and thumb positions appears to be much most distinct, indicating that having the thumb slightly abducted and the fingers grouped is a preferable position at y = 180°, whereas at y = 0°, having the thumb adducted and fingers slightly spread yielded higher lift values. Results show that finger and thumb positioning in swimming is a determinant of the propulsive force produced during swimming; indeed, this force is dependent on the direction of the flow over the hand and forearm, which changes across the arm’s stroke.


2020 ◽  
Vol 29 (3) ◽  
pp. 275-288
Author(s):  
Elvis Žic ◽  
Patrik Banko ◽  
Luka Lešnik

As a very important element of most water supply systems, valves are exposed to the effects of strong hydrodynamic forces. When exposed to large physical quantities, the valve and piping can be damaged, which could endanger the performance of a water supply system. This is the main reason why it is necessary to foresee and determine the maximum values of velocity, pressure and other physical quantities that can occur in the system under certain conditions. Predicting extreme conditions allows us to correctly size the valve for the expected conditions to which the valve might be exposed, which is also the main objective of this paper. One of the methods for predicting and determining extreme values on a valve is to perform a simulation with computational fluid dynamics (CFD). This is exactly the method used in the preparation of this paper with the aim of gaining insight into the physical magnitudes for models of gate valves positioned inside a pipe under characteristic degrees of valve closure. The Ansys CFX 19.1 and Ansys Fluent 19.1 software was used to simulate the hydrodynamic analysis and obtain the required results. The hydrodynamic analysis was performed for four opening degrees of gate valve


Sign in / Sign up

Export Citation Format

Share Document