Dynamic performance of a current-phase control method for zone-control induction heating systems

2009 ◽  
Author(s):  
Ha Pham Ngoc ◽  
H. Fujita ◽  
K. Ozaki ◽  
N. Uchida
Keyword(s):  
Induction Heating ◽  
Control Method ◽  
Dynamic Performance ◽  
Phase Control ◽  
Current Phase ◽  
Heating Systems ◽  
Zone Control ◽  
A Current

Study on Improving Power System Damping Characteristic in Novel Excitation System

2011 ◽  
Vol 383-390 ◽  
pp. 2447-2452
Author(s):  
Pei Hong Yang ◽  
Gui Mei Cui ◽  
Wen Ying Liu
Keyword(s):  
Power System ◽  
Control Method ◽  
Damping Ratio ◽  
Dynamic Performance ◽  
Decoupling Control ◽  
Excitation Voltage ◽  
Excitation System ◽  
Reactive Current ◽  
Simulation Results ◽  
A Current

A novel excitation system based on full controlled devices rectifier is proposed in this article, and the excitation system can provide double kinds of damping for power system by controlling the excitation voltage of DC side and exchanging reactive with generator. Through the Mat lab / Simu link simulation platform, a circuit model is established. This paper presents a current feed forward decoupling control method and the active and reactive current can be controlled independently by the method. The simulation results of two-area including four generators system shows the system damping ratio is improved significantly, and has better dynamic performance than conventional excitation system .

Innovative electrotechnological systems to provide the temperature modes of technological pipelines

2019 ◽  
Vol 2 (1) ◽  
pp. 29-39 ◽  
Author(s):  
S. G. Konesev ◽  
P. A. Khlyupin
Keyword(s):  
Induction Heating ◽  
Thermal Exposure ◽  
Heating System ◽  
The Arctic ◽  
Process Conditions ◽  
Heating Systems ◽  
Fluid Properties ◽  
Low Efficiency ◽  
Extreme North ◽  
Induction Heating System

Introduction: the systems of thermal effects on thermo-dependent, viscous and highly viscous liquids under conditions of the Arctic and the Extreme North are considered. Low efficiency and danger of heating systems based on burned hydrocarbons, heated liquids and steam are shown. Electrothermal heating systems used to maintain thermo-dependent fluids in a fluid state are considered. The evaluation of the effectiveness of the application of the most common electrothermal system — heating cables (tapes). The most effective electrothermal system based on induction technologies has been determined. Materials and methods: considered methods of thermal exposure to maintain the fluid properties of thermo-dependent fluids at low extreme temperatures. Results: presents an induction heating system and options for its implementation in the Extreme North and the Arctic. Conclusions: induction heating system to minimize loss of product quality, improve the system performance under changing process conditions, eliminate fire product, to reduce the influence of the human factor.

scholarly journals Bidirectional Power Sharing for DC Microgrid Enabled by Dual Active Bridge DC-DC Converter

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 404
Author(s):  
Sara J. Ríos ◽  
Daniel J. Pagano ◽  
Kevin E. Lucas
Keyword(s):  
Power Management ◽  
Distribution Systems ◽  
Control Method ◽  
Dynamic Performance ◽  
Management Control ◽  
Photovoltaic System ◽  
Dc Microgrid ◽  
Dual Active Bridge ◽  
Control Scheme ◽  
Bidirectional Power Flow

Currently, high-performance power conversion requirements are of increasing interest in microgrid applications. In fact, isolated bidirectional dc-dc converters are widely used in modern dc distribution systems. The dual active bridge (DAB) dc-dc converter is identified as one of the most promising converter topology for the mentioned applications, due to its benefits of high power density, electrical isolation, bidirectional power flow, zero-voltage switching, and symmetrical structure. This study presents a power management control scheme in order to ensure the power balance of a dc microgrid in stand-alone operation, where the renewable energy source (RES) and the battery energy storage (BES) unit are interfaced by DAB converters. The power management algorithm, as introduced in this work, selects the proper operation of the RES system and BES system, based on load/generation power and state-of-charge of the battery conditions. Moreover, a nonlinear robust control strategy is proposed when the DAB converters are in voltage-mode-control in order to enhance the dynamic performance and robustness of the common dc-bus voltage, in addition to overcoming the instability problems that are caused by constant power loads and the dynamic interactions of power electronic converters. The simulation platform is developed in MATLAB/Simulink, where a photovoltaic system and battery system are selected as the typical RES and BES, respectively. Assessments on the performance of the proposed control scheme are conducted. Comparisons with the other control method are also provided.

scholarly journals Sensorless Control of Voltage Peaks in Class-E Single-Ended Resonant Inverter for Induction Heating Rice Cooker

Energies ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4545
Author(s):  
Yongseung Oh ◽  
Jaeeul Yeon ◽  
Jayoon Kang ◽  
Ilya Galkin ◽  
Wonsoek Oh ◽  
...  
Keyword(s):  
High Pressure ◽  
Breakdown Voltage ◽  
Induction Heating ◽  
Control Method ◽  
Supply Voltage ◽  
Bipolar Transistors ◽  
Insulated Gate Bipolar Transistors ◽  
Voltage Fluctuations ◽  
Resonant Inverter ◽  
Do So

Single-ended (SE) resonant inverters are widely used as power converters for high-pressure rice cooker induction, with 1200 V insulated-gate bipolar transistors (IGBTs) being used as switching devices for kW-class products. When voltage fluctuations occur at the input stage of an SE resonant inverter, the resonant voltage applied to the IGBT can be directly affected, potentially exceeding the breakdown voltage of the IGBT, resulting in its failure. Consequently, the resonant voltage should be limited to below a safety threshold—hardware resonant voltage limiting methods are generally used to do so. This paper proposes a sensorless resonant voltage control method that limits the increase in the resonant voltage caused by overvoltage or supply voltage fluctuations. By calculating and predicting the resonance voltage through the analysis of the resonance circuit, the resonance voltage is controlled not to exceed the breakdown voltage of the IGBT. The experimental results of a 1.35 kW SE resonant inverter for a high-pressure induction heating rice cooker were used to verify the validity of the proposed sensorless resonant voltage limiting method.

Sign in / Sign up

Export Citation Format

Share Document