Optimization of flat plate heat sink using genetic algorithm

2011 ◽  
Author(s):  
S. Manivannan ◽  
S. Prasanna Devi ◽  
R. Arumugam
Keyword(s):  
Genetic Algorithm ◽  
Flat Plate ◽  
Heat Sink ◽  
Plate Heat

Thermal Performance Evaluation of Friction Stir Welded Flat Plate Heat Sink Using CFD Analysis

2015 ◽  
Vol 787 ◽  
pp. 505-509
Author(s):  
A.K. Lakshminarayanan ◽  
M. Suresh
Keyword(s):  
Flat Plate ◽  
Heat Sink ◽  
High Efficiency ◽  
Base Plate ◽  
Software Tool ◽  
Cover Plate ◽  
Air Cooling ◽  
Cooling Systems ◽  
Plate Heat ◽  
Friction Stir

In an era of compact cooling requirements, where air cooling systems seem to be ineffective and consistently, being replaced by liquid cooled systems, with greater watt density heat energy dissipation. Such cooling systems must work with good quality enabling high efficiency. Hence, an attempt is made to fabricate an aluminum alloy based flat plate heat sink with cover and base plate using friction stir welding. The base plate is machined to obtain channels for fluid flow and the cover plate is fitted in the base plate and welded. Two such configurations of these heat sinks were fabricated with varying channel lengths and number of channels. The flow characteristics of the model for these configurations were analyzed numerically using computational fluid dynamics (CFD) software tool, ANSYS fluent 14.

scholarly journals Integration of a Pulsating Heat Pipe in a Flat Plate Heat Sink

2014 ◽  
Author(s):  
Mitchell P. Hoesing ◽  
Gregory J. Michna
Keyword(s):  
Thermal Resistance ◽  
Flat Plate ◽  
Heat Pipe ◽  
Heat Sink ◽  
New Technologies ◽  
Operating Conditions ◽  
Working Fluid ◽  
High Heat Flux ◽  
Pulsating Heat Pipe ◽  
Plate Heat

The ongoing development of faster and smaller electronic components has led to a need for new technologies to effectively dissipate waste thermal energy. The pulsating heat pipe (PHP) shows potential to meet this need, due to its high heat flux capacity, simplicity, and low cost. A 20-turn flat plate PHP was integrated into an aluminum flat plate heat sink with a simulated electronic load. The PHP heat sink used water as the working fluid and had 20 parallel channels with dimensions 2 mm × 2 mm × 119 mm. Experiments were run under various operating conditions, and thermal resistance of the PHP was calculated. The performance enhancement provided by the PHP was assessed by comparing the thermal resistance of the heat sink with no working fluid to that of it charged with water. Uncharged, the PHP was found to have a resistance of 1.97 K/W. Charged to a fill ratio of approximately 75% and oriented vertically, the PHP achieved a resistance of .49 K/W and .53 K/W when the condenser temperature was set to 20°C and 30°C, respectively. When the PHP was tilted to 45° above horizontal the PHP had a resistance of .76 K/W and .59 K/W when the condenser was set 20°C and 30°C, respectively. The PHP greatly improves the heat transfer properties of the heat sink compared to the aluminum plate alone. Additional considerations regarding flat plate PHP design are also presented.

scholarly journals Taguchi Based Linear Regression Modeling of Flat Plate Heat Sink

2010 ◽  
Vol 5 (1) ◽  
pp. 36-44 ◽  
Author(s):  
S. Manivannan ◽  
R. Arumugam ◽  
N.M. Sudharsan ◽  
S. Prasanna D
Keyword(s):  
Linear Regression ◽  
Flat Plate ◽  
Heat Sink ◽  
Regression Modeling ◽  
Plate Heat ◽  
Linear Regression Modeling

Heat Transfer and Hydraulic Characteristics of Cooling Water in a Flat Plate Heat Sink for High Heat Flux IGBT

2016 ◽  
Author(s):  
Chang-Nian Chen ◽  
Ji-Tian Han ◽  
Wei-Ping Gong ◽  
Tien-Chien Jen
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flat Plate ◽  
Heat Sink ◽  
High Heat ◽  
Heat Fluxes ◽  
High Heat Flux ◽  
Hydraulic Characteristics ◽  
Flow Rates ◽  
Plate Heat

High heat flux is very dangerous for electronic heat transfer, such as IGBT (Insulated Gate Bipolar Transistor) cooling. In order to explore and master the heat transfer and hydraulic characteristics for IGBT cooling, experiments have been carried out to study the situation mentioned above in a flat plate heat sink, which was designed for high heat flux IGBT cooling. The geometrical parameters of the test section are as follows: outline dimension 229 mm × 124 mm × 30 mm; flow channels of 229 mm × 3 mm × 4 mm in total of 20. The experiments performed at atmospheric pressure and with inlet temperatures of 25–35°C, heat fluxes of 3.5–18.9 kW/m2. The influence of temperatures, heat fluxes on IGBT surface temperature and the cooling effect of the liquid cold plate have been investigated under a range of flow rates of 280–2300 kg/m2s. It was found that the heat transfer enhancement was very obvious using this kind of small sized channel for IGBT cooling, which was tens of times of the effect than air cooling or triple of the effect than that in normal sized channels. And the heat transfer enhancement increases with increasing heat fluxes and flow rates, while it decreases with increasing inlet temperatures. Most of the experimental results show good cooling effect as expected. However, it is dangerous for the cooling system under high heat fluxes when the system starts or stops suddenly, when the Respond Time (RT) is less than 5 seconds to cut off heated power. Also, the cooling performance is bad when the heat fluxes increased greatly, which is considered as abnormal situation in operating. The effect on IGBT surface temperature of heat flux is more obvious when the average Nusselt Number is smaller. For hydraulic characteristics observed, it was found that the flow friction increased with flow rates increasing, but the pressure drops of heated flow channels ahead were slightly larger than those back, especially under large flow rates conditions. That is because the temperatures of flow heated in channels ahead are lower than those back, which causes the fluid viscosity to be higher. At last, this paper suggested a series of method for enhancing heat transfer in flat plate heat sink, and also gave some ways to avoid heat transfer dangerous situations for IGBT cooling, which can provide a basis for thermodynamic and hydraulic calculation of flat plate heat sink design and lectotype.

An experimental investigation and optimisation of flat plate heat sink

2012 ◽  
Vol 4 (4) ◽  
pp. 340
Author(s):  
S. Manivannan ◽  
R. Arumugam ◽  
S. Prasanna Devi ◽  
N.M. Sudharsan ◽  
S. Paramasivam
Keyword(s):  
Experimental Investigation ◽  
Flat Plate ◽  
Heat Sink ◽  
Plate Heat

scholarly journals THE BEHAVIOR OF HEAT SINK-IMPINGEMENT COOLING WITH FLAT PLATE AND ARCED FINS MODELS

2022 ◽  
Vol 26 (1) ◽  
pp. 1-14
Author(s):  
Dalmn Y. Taha ◽  
◽  
Dhamyaa S. Khudhur ◽  
Layla M. Nassir ◽  
◽  
...  
Keyword(s):  
Statistical Analysis ◽  
Flat Plate ◽  
Heat Sink ◽  
Reynolds Numbers ◽  
Heat Sinks ◽  
Impingement Cooling ◽  
Plate Heat ◽  
Arc Model ◽  
Numerical Predictions ◽  
Better Than

In this paper, a statistical analysis was applied to the numerical predictions of temperature distribution for the heat sinks. There are two types of heat sink with an array of impingement. The first type is a flat plate heat sink, and the second type is arcs-fins heat sinks. The second type category considers five models (A, B, C, D, and E). The shapes of fins were changed, but the thickness, distance between fins, and radius were held fixed for comparing and analyzing them depending upon the improvement of the fin geometry of heat sink. The heat sinks of the two types are subjected to multi impinging flow at different Reynolds numbers (7000-11000). Thermodynamic and hydraulic results were collected. The best model was calculated through a statistical analysis. The efficiency of an arcs-fin heat sink was superior to that of the flat plate heat sink. The findings of Model D were more appropriate than those of the other models. The concave arc near the heat sink's exit (model D) created better effect than the convex arc (model E), despite the fact that the (model D) shape fins being identical to (model E) shape fins (only rotated 180° at the same location). However, Descriptive Statistics manifested that in all situations, the mean temperature for (model D) is better than (model E). The results of comparison between the flat plate heat sink and models (D and E) evinced that the average heat sink temperature in the suggested design reduced via 12%, 8%, while the (model E) decreased by 12%, 7% for Re (7000, 9000), respectively. In addition, the two models maintained the same percentage of (8% and 7%) improvement at Re (11000). The correlation coefficient between the flat plate and the arcs-fins heat sink for model B has the highest value (0.809), while model A has the lowest value of correlation (0.673).

Sign in / Sign up

Export Citation Format

Share Document