Numerical Study Analysis of The Effect of Trailing Edge Thickness of Low-Pressure Steam Turbine Stator on Steam Condensation

2021 ◽  
Author(s):  
Gilang Muhammad ◽  
Lohdy Diana ◽  
Achmad Bahrul Ulum
Keyword(s):  
Steam Turbine ◽  
Numerical Study ◽  
Low Pressure ◽  
Study Analysis ◽  
Steam Condensation ◽  
Trailing Edge ◽  
Turbine Stator ◽  
Pressure Steam

Detailed Numerical Study of the Main Sources of Loss and Flow Behavior in Low Pressure Steam Turbine Exhaust Hoods

2017 ◽  
Author(s):  
Dickson Munyoki ◽  
Markus Schatz ◽  
Damian M. Vogt
Keyword(s):  
Steam Turbine ◽  
Numerical Study ◽  
Flow Behavior ◽  
Low Pressure ◽  
Operating Conditions ◽  
Pressure Recovery ◽  
Exhaust Hood ◽  
Recovery Coefficient ◽  
Pressure Steam ◽  
Underlying Mechanisms

The performance of the axial-radial diffuser downstream of the last low-pressure steam turbine stages and the losses occurring subsequently within the exhaust hood directly influences the overall efficiency of a steam power plant. It is estimated that an improvement of the pressure recovery in the diffuser and exhaust hood by 10% translates into 1% of last stage efficiency [11]. While the design of axial-radial diffusers has been the object of quite many studies, the flow phenomena occurring within the exhaust hood have not received much attention in recent years. However, major losses occur due to dissipation within vortices and inability of the hood to properly diffuse the flow. Flow turning from radial to downward flow towards the condenser, especially at the upper part of the hood is essentially the main cause for this. This paper presents a detailed analysis of the losses within the exhaust hood flow for two operating conditions based on numerical results. In order to identify the underlying mechanisms and the locations where dissipation mainly occurs, an approach was followed, whereby the diffuser inflow is divided into different sectors and pressure recovery, dissipation and finally residual kinetic energy of the flow originating from these sectors is calculated at different locations within the hood. Based on this method, the flow from the topmost sectors at the diffuser inlet is found to cause the highest dissipation for both investigated cases. Upon hitting the exhaust hood walls, the flow on the upper part of the diffuser is deflected, forming complex vortices which are stretching into the condenser and interacting with flow originating from other sectors, thereby causing further swirling and generating additional losses. The detailed study of the flow behavior in the exhaust hood and the associated dissipation presents an opportunity for future investigations of efficient geometrical features to be introduced within the hood to improve the flow and hence the overall pressure recovery coefficient.

Unsteady Flow Effect on Nonequilibrium Condensation in 3-D Low Pressure Steam Turbine Stages

2013 ◽  
Author(s):  
Satoshi Miyake ◽  
Satoru Yamamoto ◽  
Yasuhiro Sasao ◽  
Kazuhiro Momma ◽  
Toshihiro Miyawaki ◽  
...  
Keyword(s):  
Unsteady Flow ◽  
Steam Turbine ◽  
Cross Sections ◽  
Rotor Blade ◽  
Numerical Study ◽  
Flow Characteristics ◽  
Low Pressure ◽  
Multi Stage ◽  
Pressure Steam ◽  
Nonequilibrium Condensation

A numerical study simulating unsteady 3-D wet-steam flows through three-stage stator-rotor blade rows in a low-pressure steam turbine model experimentally conducted by Mitsubishi Heavy Industry (MHI) was presented in the last ASME Turbo Expo by our group. In this study, the previous discussion is extended to the discussion how nonequilibrium condensation is influenced by unsteady wakes and corner vortices from prefaced multi-stage blade rows. Unsteady 3-D flows through three-stage stator-rotor blade rows are simulated assuming nonequilibrium condensation. Flows with a different inlet flow condition are calculated and the results are compared with each other. Instantaneous condensate mass fractions are visualized at different spans and cross sections in the three-stage stator and rotor blade rows. Also the time and space dependent values are plotted and the obtained unsteady flow characteristics are explained.

Paper 9: The Removal of Water from Low-Pressure Steam Turbine Blades by Trailing-Edge Suction Slots

1967 ◽  
Vol 182 (8) ◽  
pp. 94-103 ◽  
Author(s):  
D. J. Ryley ◽  
G. J. Parker
Keyword(s):  
Steam Turbine ◽  
Turbine Blades ◽  
Low Pressure ◽  
Operating Conditions ◽  
Trailing Edge ◽  
Full Size ◽  
Hollow Blade ◽  
Pressure Steam ◽  
Steam Turbine Blades ◽  
Suction Slot

This paper reports an experimental research undertaken to explore the performance of a suction slot located in the trailing edge of a representative low-pressure steam turbine fixed blade. Tests have been made on a 1-in wide section of a full-size hollow blade mounted in a single-blade test section. Typical turbine pressures were reproduced down to 3 inHg (abs.), and blade exit Mach numbers varied in the range 0·57–1·10. With round entry lips, the slot operated satisfactorily in any blade orientation, as it completely removed quantities of water that were in excess of the amount expected under operating conditions. Square entry lips gave somewhat poorer performance.

scholarly journals Failure Analysis in Lacing Wire Of Last Stage Low Pressure Steam Turbine Blade

2021 ◽  
Vol 1096 (1) ◽  
pp. 012097
Author(s):  
A M Kongkong ◽  
H Setiawan ◽  
J Miftahul ◽  
A R Laksana ◽  
I Djunaedi ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Steam Turbine ◽  
Turbine Blade ◽  
Low Pressure ◽  
Pressure Steam ◽  
Steam Turbine Blade ◽  
Last Stage

Sequential vs Multidisciplinary Coupled Optimization and Efficient Surrogate Modelling of a Last Stage and the Successive Axial Radial Diffuser in a Low Pressure Steam Turbine

2014 ◽  
Author(s):  
Kevin Cremanns ◽  
Dirk Roos ◽  
Arne Graßmann
Keyword(s):  
Steam Turbine ◽  
Design Process ◽  
Energy Demand ◽  
Three Dimensional ◽  
Flow Simulation ◽  
Low Pressure ◽  
Steam Turbines ◽  
Low Pressure Turbine ◽  
Pressure Steam ◽  
Last Stage

In order to meet the requirements of rising energy demand, one goal in the design process of modern steam turbines is to achieve high efficiencies. A major gain in efficiency is expected from the optimization of the last stage and the subsequent diffuser of a low pressure turbine (LP). The aim of such optimization is to minimize the losses due to separations or inefficient blade or diffuser design. In the usual design process, as is state of the art in the industry, the last stage of the LP and the diffuser is designed and optimized sequentially. The potential physical coupling effects are not considered. Therefore the aim of this paper is to perform both a sequential and coupled optimization of a low pressure steam turbine followed by an axial radial diffuser and subsequently to compare results. In addition to the flow simulation, mechanical and modal analysis is also carried out in order to satisfy the constraints regarding the natural frequencies and stresses. This permits the use of a meta-model, which allows very time efficient three dimensional (3D) calculations to account for all flow field effects.

20.Wetness measurements in a model multistage low pressure steam turbine

1989 ◽  
pp. 161-169 ◽  
Author(s):  
B. R. Haller ◽  
R. G. Unsworth ◽  
P. T. Walters ◽  
M. J. Lord
Keyword(s):  
Steam Turbine ◽  
Low Pressure ◽  
Pressure Steam
Sign in / Sign up

Export Citation Format

Share Document