Design of reject frequency band and multi band CPW-fed monopole antenna with control notched band for WLAN/WiMAX applications

2016 ◽  
Author(s):  
Nipont Tangthong ◽  
Rattapon Jeenawong ◽  
Somsak Akatimagool
Keyword(s):  
Frequency Band ◽  
Monopole Antenna ◽  
Notched Band ◽  
Multi Band

Compact Triple/Quadruple-Band Reconfigurable Monopole Antenna for Wireless Applications

2021 ◽  
pp. 2150277
Author(s):  
Asmaa Zugari ◽  
Wael Abd Ellatif Ali ◽  
Mohammad Ahmad Salamin ◽  
El Mokhtar Hamham
Keyword(s):  
Simple Structure ◽  
Low Cost ◽  
Ground Plane ◽  
Monopole Antenna ◽  
Pin Diode ◽  
Wireless Applications ◽  
Rectangular Patch ◽  
Antenna Performance ◽  
Compact Size ◽  
Multi Band

In this paper, a compact reconfigurable tri-band/quad-band monopole antenna is presented. To achieve the multi-band behavior, two right-angled triangles were etched in a conventional rectangular patch, and a partial ground plane is used. Moreover, the proposed multi-band antenna is printed on a low cost FR4 epoxy with compact dimensions of 0.23[Formula: see text], where [Formula: see text] is calculated at the lowest resonance frequency. To provide frequency agility, a metal strip which acts as PIN diode was embedded in the frame of the modified patch. The tri-band/quad-band antenna performance in terms of reflection coefficient, radiation patterns, peak gain and efficiency was studied. The measured results are consistent with the simulated results for both cases. The simple structure and the compact size of the proposed antenna could make it a good candidate for multi-band wireless applications.

A MULTI-BAND MONOPOLE ANTENNA WITH TWO DIFFERENT SLOTS FOR WLAN AND WIMAX APPLICATIONS

2011 ◽  
Vol 28 ◽  
pp. 173-181 ◽  
Author(s):  
Si-Ming Zhang ◽  
Fu-Shun Zhang ◽  
Wei-Mei Li ◽  
Wen-Zhu Li ◽  
Hui-Ying Wu
Keyword(s):  
Monopole Antenna ◽  
Multi Band

scholarly journals A Compact Printed Monopole Antenna for WiMAX/WLAN and UWB Applications

2018 ◽  
Vol 10 (12) ◽  
pp. 122 ◽  
Author(s):  
Zubin Chen ◽  
Baijun Lu ◽  
Yanzhou Zhu ◽  
Hao Lv
Keyword(s):  
Frequency Band ◽  
High Frequency ◽  
Field Work ◽  
Monopole Antenna ◽  
Center Frequency ◽  
High Frequency Band ◽  
Work Requirements ◽  
Printed Monopole Antenna ◽  
Printed Monopole ◽  
Uwb Applications

In this paper, a printed monopole antenna design for WiMAX/WLAN applications in cable-free self-positioning seismograph nodes is proposed. Great improvements were achieved in miniaturizing the antenna and in widening the narrow bandwidth of the high-frequency band. The antenna was fed by a microstrip gradient line and consisted of a triangle, an inverted-F shape, and an M-shaped structure, which was rotated 90° counterclockwise to form a surface-radiating patch. This structure effectively widened the operating bandwidth of the antenna. Excitation led to the generation of two impedance bands of 2.39–2.49 and 4.26–7.99 GHz for a voltage standing wave ratio of less than 2. The two impedance bandwidths were 100 MHz, i.e., 4.08% relative to the center frequency of 2.45 GHz, and 3730 MHz, i.e., 64.31% relative to the center frequency of 5.80 GHz, covering the WiMAX high-frequency band (5.25–5.85 GHz) and the WLAN band (2.4/5.2/5.8). This article describes the design details of the antenna and presents the results of both simulations and experiments that show good agreement. The proposed antenna meets the field-work requirements of cable-less seismograph nodes.

scholarly journals A Band-Rejection Vivaldi Antenna with High Selectivity Using Hybrid HRW/CCLL

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Mengfei Xiong ◽  
Junping Duan ◽  
Binzhen Zhang
Keyword(s):  
Frequency Band ◽  
Design Method ◽  
Directional Pattern ◽  
Impedance Bandwidth ◽  
Ieee 802.11A ◽  
Notch Band ◽  
Notched Band ◽  
Half Wavelength ◽  
Measurement Results ◽  
Vivaldi Antenna

A simplified notched design method for the Vivaldi antenna is exhibiting high frequency-band-selectivity characteristics. By suitably introducing half-wavelength resonator (HWR) and complementary capacitively loaded loop (CCLL), the notched-band selectivity is promoted while maintaining the wide impedance bandwidth of the antenna applicable for wireless communications. HWR is bent in the middle to focus the first notch pole, and the second notch pole is obtained by CCLL on the radiating patch. Additionally, the resonant frequency of the notched pole can be determined by the position and size of two loaded resonators in theoretical analysis, thereby realizing a wideband antenna with the desired notched band. Finally, the Vivaldi antenna of loading resonator was fabricated to verify the feasibility of this new method. Measured and simulated experimental results reveal that the antenna exhibits directional pattern in the passband, low gain at the band-rejection, and excellent selectivity within a frequency range. The simulation and measurement results are in good agreement. The proposed antenna achieves S11<−10 dB in 2.6–13.7 GHz and a notch band from 4.49 to 6.64 GHz to reject IEEE 802.11a and HIPERLAN/2 frequency band. Moreover, the proposed antenna has good frequency selectivity, and its gain is good enough in the passband with peak gain up to 10.8 dBi. This antenna design presents frequency suitability, demonstrating that a UWB antenna with a controllable notched band has been realized.

A Novel Design of Frequency Reconfigurable Antenna for UWB Application

Frequenz ◽  
2016 ◽  
Vol 70 (9-10) ◽  
Author(s):  
Xiaolin Yang ◽  
Ziliang Yu ◽  
Zheng Wu ◽  
Huajiao Shen
Keyword(s):  
Frequency Band ◽  
Dual Band ◽  
Reconfigurable Antenna ◽  
Pin Diodes ◽  
Notched Band ◽  
Uwb Applications ◽  
Novel Design ◽  
Frequency Reconfigurable Antenna

AbstractIn this paper, we present a novel frequency reconfigurable antenna which could be easily operate in a single notched-band (WiMAX (3.3–3.6 GHz)) UWB frequency band, another single notched-band (WLAN (5–6 GHz)) UWB frequency band and the dual band-notched UWB frequency band (the stopband covers the WiMAX (3.3–3.6 GHz) and WLAN (5–6 GHz)). The reconfigurability is achieved by changing the states of PIN diodes. The simulated results are in agreement well with the measured results. And the measured patterns are slightly changed with antenna reconfiguration. The proposed antenna is a good candidate for various UWB applications.

Sign in / Sign up

Export Citation Format

Share Document