Fluid Dynamics and Heat Transfer Generated by a Pair of Adjacent Impinging Synthetic Jets

2018 ◽  
Author(s):  
Jean Paul DrAlencon ◽  
David A. Gallardo ◽  
Luis Silva-Llanca
Keyword(s):  
Heat Transfer ◽  
Fluid Dynamics ◽  
Synthetic Jets

Analysis of Late Phase Severe Accident Phenomena in CANDU Plant

2017 ◽  
Vol 3 (2) ◽  
Author(s):  
D. Dupleac
Keyword(s):  
Heat Transfer ◽  
Fluid Dynamics ◽  
Late Phase ◽  
Severe Accident ◽  
Ansys Fluent ◽  
Water Depletion ◽  
Sources Of Uncertainty ◽  
Parametric Studies ◽  
Computational Fluid Dynamics Cfd ◽  
Containment Pressure

The paper overviews the analytical studies performed at Politehnica University of Bucharest on the analysis of late phase severe accident phenomena in a Canada Deuterium Uranium (CANDU) plant. The calculations start from a dry debris bed at the bottom of calandria vessel. Both SCDAPSIM/RELAP code and ansys-fluent computational fluid dynamics (CFD) code are used. Parametric studies are performed in order to quantify the effect of several identified sources of uncertainty on calandria vessel failure: metallic fraction of zirconium inside the debris, containment pressure, timing of water depletion inside calandria vessel, steam circulation in calandria vessel above debris bed, debris temperature at moment of water depletion inside calandria vessel, calandria vault nodalization, and the gap heat transfer coefficient.

Turbulent Transport in Pin Fin Arrays: Experimental Data and Predictions

2005 ◽  
Author(s):  
F. E. Ames ◽  
L. A. Dvorak
Keyword(s):  
Heat Transfer ◽  
Fluid Dynamics ◽  
Boundary Layers ◽  
Fluid Dynamic ◽  
Turbulent Transport ◽  
Turbulence Models ◽  
Reynolds Numbers ◽  
Velocity Profiles ◽  
Pin Fin ◽  
Pin Fin Arrays

The objective of this research has been to experimentally investigate the fluid dynamics of pin fin arrays in order to clarify the physics of heat transfer enhancement and uncover problems in conventional turbulence models. The fluid dynamics of a staggered pin fin array have been studied using hot wire anemometry with both single and x-wire probes at array Reynolds numbers of 3000; 10,000; and 30,000. Velocity distributions off the endwall and pin surface have been acquired and analyzed to investigate turbulent transport in pin fin arrays. Well resolved 3-D calculations have been performed using a commercial code with conventional two-equation turbulence models. Predictive comparisons have been made with fluid dynamic data. In early rows where turbulence is low, the strength of shedding increases dramatically with increasing in Reynolds numbers. The laminar velocity profiles off the surface of pins show evidence of unsteady separation in early rows. In row three and beyond laminar boundary layers off pins are quite similar. Velocity profiles off endwalls are strongly affected by the proximity of pins and turbulent transport. At the low Reynolds numbers, the turbulent transport and acceleration keep boundary layers thin. Endwall boundary layers at higher Reynolds numbers exhibit very high levels of skin friction enhancement. Well resolved 3-D steady calculations were made with several two-equation turbulence models and compared with experimental fluid mechanic and heat transfer data. The quality of the predictive comparison was substantially affected by the turbulence model and near wall methodology.

Micro Fluidic Jets for Thermal Management of Electronics

Volume 4 ◽  
2004 ◽  
Author(s):  
Jivtesh Garg ◽  
Mehmet Arik ◽  
Stanton Weaver ◽  
Seyed Saddoughi
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Heated Surface ◽  
Turbulent Jets ◽  
Harmonic Signal ◽  
Synthetic Jet ◽  
Synthetic Jets ◽  
Small Scale ◽  
Air Cooling ◽  
Infrared Thermal Imaging

Micro fluidics devices are conventionally used for boundary layer control in many aerospace applications. Synthetic Jets are intense small scale turbulent jets formed from entrainment and expulsion of the fluid in which they are embedded. The idea of using synthetic jets in confined electronic cooling applications started in late 1990s. These micro fluidic devices offer very efficient, high magnitude direct air-cooling on the heated surface. A proprietary synthetic jet designed in General Electric Company was able to provide a maximum air velocity of 90 m/s from a 1.2 mm hydraulic diameter rectangular orifice. An experimental study for determining the thermal performance of a meso scale synthetic jet was carried out. The synthetic jets are driven by a time harmonic signal. During the experiments, the operating frequency for jets was set between 3 and 4.5 kHz. The resonance frequency for a particular jet was determined through the effect on the exit velocity magnitude. An infrared thermal imaging technique was used to acquire fine scale temperature measurements. A square heater with a surface area of 156 mm2 was used to mimic the hot component and extensive temperature maps were obtained. The parameters varied during the experiments were jet location, driving jet voltage, driving jet frequency and heater power. The output parameters were point wise temperatures (pixel size = 30 μm), and heat transfer enhancement over natural convection. A maximum of approximately 8 times enhancement over natural convection heat transfer was measured. The maximum coefficient of cooling performance obtained was approximately 6.6 due to the low power consumption of the synthetic jets.

Sign in / Sign up

Export Citation Format

Share Document