scholarly journals ISO standard implementation impact in COVID-19 erra on UV-lighting devices

2020 ◽  
Author(s):  
Valeria Nenova ◽  
Maria V. Nenova ◽  
Desislava V. Georgieva ◽  
Vesselin E. Gueorguiev
Keyword(s):  
Iso Standard

Comparative study of stress analysis of gears with different helix angle using the ISO 6336 standard and tooth contact analysis methods

2016 ◽  
Vol 230 (7-8) ◽  
pp. 1350-1358 ◽  
Author(s):  
Layue Zhao ◽  
Robert C Frazer ◽  
Brian Shaw
Keyword(s):  
Stress Analysis ◽  
Contact Stress ◽  
Helix Angle ◽  
Contact Analysis ◽  
Bending Stress ◽  
Contact Ratio ◽  
Tooth Contact Analysis ◽  
Tooth Contact ◽  
Iso Standard ◽  
Analysis Methods

With increasing demand for high speed and high power density gear applications, the need to optimise gears for minimum stress, noise and vibration becomes increasingly important. ISO 6336 contact and bending stress analysis are used to determine the surface load capacity and tooth bending strength but dates back to 1956 and although it is constantly being updated, a review of its performance is sensible. Methods to optimise gear performance include the selection of helix angle and tooth depth to optimise overlap ratio and transverse contact ratio and thus the performance of ISO 6336 and tooth contact analysis methods requires confirmation. This paper reviews the contact and bending stress predicted with four involute gear geometries and proposes recommendations for stress calculations, including a modification to contact ratio factor Zɛ which is used to predict contact stress and revisions to form factor YF and helix angle factor Yβ which are cited to evaluate bending stress. The results suggest that there are some significant deviations in predicted bending and contact stress values between proposal methods and original ISO standard. However, before the ISO standard is changed, the paper recommends that allowable stress numbers published in ISO 6336-5 are reviewed because the mechanisms that initiate bending and contact fatigue have also changed and these require updating.

Evaluation of Horizontal Patternators According to International Standard Requirements for Boom Sprayers

2021 ◽  
Vol 64 (5) ◽  
pp. 1635-1646
Author(s):  
Emilio Gil ◽  
Mariana Bueno ◽  
Javier Campos ◽  
Montserrat Gallart ◽  
Joao P. A. R. Da Cunha
Keyword(s):  
Distribution Patterns ◽  
Volume Distribution ◽  
List Type ◽  
Operating Pressure ◽  
Spray Pattern ◽  
Iso Standard ◽  
Iso Standards ◽  
Technical Requirements ◽  
Spray Distribution ◽  
Technical Specifications

HighlightsHorizontal distribution according ISO Standard 16119 is a measurement procedure to evaluate boom sprayers.ISO Standards 5682-1 and 5682-2 establish technical requirements for horizontal patternators.In this study, three types of patternators were evaluated to test their capability to meet the standards.The evaluated patternators showed similar results for spray distribution patterns.Minor deviations from ISO Standard 5682 did not imply differences according ISO Standard 16119.Abstract. Uniformity of spray volume distribution is one of the officially established measurements for the evaluation of horizontal boom sprayers according to ISO Standard 16119 and requirements established by ISO Standard 16122. Measurement of spray distribution patterns requires the use of specific devices such as horizontal patternators, which are included in the technical specifications for ISO Standards 5682-1 and 5682-2. Three such devices were tested, including two manual patternators (fixed and mobile) and one electronic patternator. According to information provided by the manufacturers, all three patternators align with ISO requirements. This study evaluated and compared the results obtained with the three patternators. Specifically, the horizontal distributions measured by the patternators were evaluated and compared using four nozzle types (XR 11003, AIXR 11003, TTJ60 11003, and AITTJ60 11003), three boom heights, and three operating pressures. Tests were conducted to quantify single-nozzle spray patterns, the coefficient of variation (CV) of the entire boom distribution, the liquid recovery capability of the three patternators, and the ability to simulate the entire boom spray distribution from a single-nozzle spray pattern. Results demonstrated correct functioning of all three patternators, resulting in identical conclusions considering the requirements established in the ISO standards. The CV values of the horizontal distributions were less than 10% for all cases. Moreover, the trends in values for all the evaluated factors (nozzle type, boom height, and operating pressure) were the same, independent of the patternator used. Keywords: ISO 16119, ISO 16122, ISO 5682, Liquid recovery, Nozzle spray pattern, Patternator, Spray boom, Transverse distribution, Uniformity.

Multicenter methodology comparison of the FDA and ISO standard for measurement of in vitro UVA protection of sunscreen products

2018 ◽  
Vol 189 ◽  
pp. 185-192 ◽  
Author(s):  
S. Bielfeldt ◽  
E. Klette ◽  
M. Rohr ◽  
B. Herzog ◽  
J. Grumelard ◽  
...  
Keyword(s):  
Iso Standard ◽  
Sunscreen Products

scholarly journals Study of a test methodology to assess potential drift generated by air-assisted sprayers

2013 ◽  
Vol 44 (2s) ◽  
Author(s):  
Paolo Balsari ◽  
Paolo Marucco ◽  
Claudio Bozzer ◽  
Mario Tamagnone
Keyword(s):  
Experimental Data ◽  
Ad Hoc ◽  
Sustainable Use ◽  
Spray Drift ◽  
Field Crop ◽  
The European Union ◽  
Pesticide Application ◽  
Buffer Zones ◽  
Iso Standard ◽  
Test Methodology

During pesticide application spray drift may cause diffuse pollution phenomena in the environment. In the last years the European Union, through the Directive on the sustainable use of pesticides (128/2009 EC), has recommended the adoption of measures enabling to prevent spray drift. Among these measures, the adoption of buffer zones beside the sprayed fields requires to consider different widths for these no spray zones according to the amount of spray drift generated by the spraying equipment used for application. It is therefore necessary to classify the different sprayer models according to drift risk. For what concerns the sprayers used on arboreal crops, in order to make this classification in a simple and quick way as it was already proposed for the field crop sprayers (ISO FDIS 22369-3), a study was started aimed at defining a methodology to assess potential drift produced by the different sprayer models in absence of wind, using ad hoc test benches. On the basis of the positive first experimental data obtained, a first proposal for a new ISO standard methodology was prepared.

An audit of laryngoscopes and application of a new ISO standard

2011 ◽  
Vol 21 (4) ◽  
pp. 428-434 ◽  
Author(s):  
Paul A. Baker ◽  
Shane McQuoid ◽  
John M.D. Thompson ◽  
Robert J. Jacobs
Keyword(s):  
Iso Standard
Sign in / Sign up

Export Citation Format

Share Document