Electrical And Plasma Characteristics Of A One Atmosphere Glow Discharge Plasma Reactor

Author(s):  
P.D. Spence ◽  
J.R. Roth
2012 ◽  
Vol 61 (4) ◽  
pp. 045201
Author(s):  
Hu Ming ◽  
Wan Shu-De ◽  
Zhong Lei ◽  
Liu Hao ◽  
Wang Hai

2001 ◽  
Vol os-10 (3) ◽  
pp. 1558925001OS-01 ◽  
Author(s):  
J. Reece Roth ◽  
Zhiyu Chen ◽  
Daniel M. Sherman ◽  
Fuat Karakaya ◽  
Peter P.-Y. Tsai ◽  
...  

A technique for generating active species with the One Atmosphere Uniform Glow Discharge Plasma (OAUGDP) has been developed and used to sterilize and increase the surface energy, wettability and wickability of nonwoven fabrics. The OAUGDP is a non-thermal, fourth-state-of-matter plasma with the classical characteristics of a low pressure DC normal glow discharge that operates in air (and other gases) at atmospheric pressure. No vacuum system or batch processing is necessary, and a wide range of applications to fabrics and polymeric webs can be accommodated in a parallel plate plasma reactor. In addition to directly exposing webs and workpieces to active species for surface energy increase in a parallel-plate reactor, we have shown that active species capable of sterilization can be convected at near room temperature to a remote exposure chamber. This technology is simple, produces many effects that can be obtained in no other way, generates minimal pollutants or unwanted byproducts, and is suitable for online treatment of webs, films, and fabrics. Early exposures of nonwoven fabrics to the OAUGDP required minutes to produce relatively small increases of surface energy. These durations appeared too long for commercial application to fast-moving webs. Recent improvements in OAUGDP power density, plasma quality and impedance matching of the power supply to the parallel plate plasma reactor have made it possible to raise the surface energy of a variety of polymeric webs (PP, PET, PE, etc.) to levels in the range of 60 to 70 dynes/cm with one second of exposure. In most cases these high surface energies were not durable, and fell off to 50 dynes/cm after periods of weeks to months. Here, we report the exposure of nonwoven fabrics made of PP and PET at the UTK Textiles and Nonwovens Development Center (TANDEC) to an impedance matched parallel plate OAUGDP for durations ranging from one second to several tens of seconds. Data will be reported on the surface energy, wettability and wickability as functions of time of exposure, and of the aging effect after exposure. We will report the use of a OAUGDP with air as the working gas to sterilize a broad range of microorganisms on a variety of surfaces, and in several distinct applications. These include a Remote Exposure Reactor to sterilize large workpieces 20 centimeters or more from the plasma-generating region, and a sterilizable air filter.


1997 ◽  
Vol 67 (5) ◽  
pp. 359-369 ◽  
Author(s):  
Peter P. Tsai ◽  
Larry C. Wadsworth ◽  
J. Reece Roth

In industrial applications, a steady-state glow discharge capable of operating at one atmosphere would allow many plasma-related surface modification processes to be done on the production line, rather than in expensive vacuum systems that force batch processing. In this paper, we report some encouraging results from the plasma surface treatment of polypropylene meltblown nonwovens in the UTK one-atmosphere glow discharge plasma reactor. This reactor generates a large volume (up to 2.4 liters), low power (less than 150 watts), uniform glow discharge plasma in a parallel plate configuration with oval electrodes of 213 cm2 face area, the lower electrode being covered with a 3.2 mm thick insulating Pyrex surface. The plates are set up in an enclosed box that makes it possible to control the working gas used, and the spacing between the plates can be varied. This reactor is energized by a custom-made high impedance kilohertz power supply capable of supplying up to 5 kilowatts of kilohertz power at RMS voltages up to 10 kV, and over a frequency range from 1 to 100 kHz. Exposing a wide variety of polymer fabrics reveals that the wettability, wickability, printability, and surface contact angle of the materials are significantly changed in a direction that may lead to new uses for these materials.


2017 ◽  
Vol 88 ◽  
pp. 225-231 ◽  
Author(s):  
M.F. Bekkara ◽  
Y. Benmimoun ◽  
A. Tilmatine ◽  
K. Miloudi ◽  
S. Flazi

Processes ◽  
2021 ◽  
Vol 9 (11) ◽  
pp. 2063
Author(s):  
Stephan Renninger ◽  
Paul Rößner ◽  
Jan Stein ◽  
Maike Lambarth ◽  
Kai Peter Birke

Plasma technology reaches rapidly increasing efficiency in catalytic applications. One such application is the splitting reaction of CO2 to oxygen and carbon monoxide. This reaction could be a cornerstone of power-to-X processes that utilize electricity to produce value-added compounds such as chemicals and fuels. However, it poses problems in practice due to its highly endothermal nature and challenging selectivity. In this communication a glow discharge plasma reactor is presented that achieves high energy efficiency in the CO2 splitting reaction. To achieve this, a magnetic field is used to increase the discharge volume. Combined with laminar gas flow, this leads to even energy distribution in the working gas. Thus, the reactor achieves very high energy efficiency of up to 45% while also reaching high CO2 conversion efficiency. These results are briefly explained and then compared to other plasma technologies. Lastly, cutting edge energy efficiencies of competing technologies such as CO2 electrolysis are discussed in comparison.


2013 ◽  
Vol 2013 ◽  
pp. 1-6
Author(s):  
Sankar Moni Borah

This paper reports on the study of direct current (DC) magnetron glow discharge plasma characteristics in a cylindrical magnetron system in argon-nitrogen. Presence of nitrogen gas makes the plasma environment reactive, and it results in significant changes of the plasma properties—number density, electron temperature, floating potential, and sheath thickness. Applied magnetic field is a parameter which is closely related to proper deposition of thin film. Cylindrical Langmuir probe and Emissive probe are used as diagnostics for the estimation of various plasma parameters indicated earlier. Controlled titanium nitride (TiN) thin film deposition on bell-metal at different argon-nitrogen gases ratio is another important study reported.


Sign in / Sign up

Export Citation Format

Share Document